Microchip Technology

ATSAM3U4CA-AU - 96MHz 256KB Flash MCU | Microchip

MPN: ATSAM3U4CA-AU ✓ چالاک
1.8 V or 3.3 V Vdss 0.6 µA Id 100-pin LQFP, 14 x 14 mm Package 96 MHz Speed 256 KB Memory
MOQ: 1 |

ATSAM3U4CA-AU گشتی

Microchip ATSAM3U4CA-AU is a 32-bit ARM Cortex-M3 microcontroller operating up to 96 MHz, with 256 KB of embedded Flash and 52 KB of SRAM in a 100-pin LQFP package measuring 14 x 14 mm. It combines a high-performance 32-bit RISC processor, dual-bank Flash, a Memory Protection Unit, and extensive serial peripherals for compact embedded control systems.

A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals on one package. The ATSAM3U4CA-AU belongs to the SAM3U family of ARM-based Flash microcontrollers. Its Cortex-M3 core supports the Thumb-2 instruction set and revision 2.0 architecture, providing a direct software-execution environment for control logic, communications, data acquisition, and human-interface applications.

The device provides 128-bit-wide Flash access with a memory accelerator and dual-bank organization. It includes USB 2.0 device operation at 480 Mbps with a 4 KB FIFO and up to seven bidirectional endpoints. Communication resources include up to four USARTs, one UART, two TWI interfaces, one SPI interface, one SSC, and one HSMCI controller. The low-power RTC is specified at 0.6 µA in the cited device data.

Operating from 1.8 V or 3.3 V, the ATSAM3U4CA-AU is suited to industrial control, data acquisition, USB-connected portable equipment, HMI panels, and embedded accessories. Its 52 KB SRAM supports protocol buffers, display data, and real-time control state, while dual-bank Flash can assist firmware update and supervisory code isolation when implemented according to the manufacturer’s procedures.

Board design should preserve clean power distribution around the 100-pin LQFP. Place decoupling capacitors close to the supply pins, route high-speed USB and memory signals with short paths and a continuous reference plane, and check all peripheral pins against the exact package drawing before releasing artwork. Firmware should use the matching SAM device definition and peripheral configuration from Microchip’s development environment.

Thermal design becomes important when the MCU operates continuously at 96 MHz with several communication peripherals active. Validate worst-case junction temperature, regulator headroom, and enclosure temperature rather than relying only on ambient temperature. Decoupling values, clock stability, USB impedance, and exposed functionality should be confirmed against the manufacturer datasheet and board-design guidance.

This product record combines the verified device specifications, family-level replacement analysis, application guidance, and package-aware selection considerations. It helps engineers identify whether the 96 MHz Cortex-M3 architecture, USB support, memory capacity, and 100-pin LQFP footprint fit a design before committing to the ATSAM3U4CA-AU.

جێگرەوەکانی جێگۆڕکێ بۆ ATSAM3U4CA-AU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ATSAM3U4CA-AU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Series, Maximum Clock Speed, Flash Memory, USB.

Microchip Technology
Package: 100-LQFP (14 x 14 mm)
Series: SAM3A
Maximum Clock Speed: 84 MHz
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Series: SAM3N
Maximum Clock Speed: 48 MHz
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 100-LQFP (14 x 14 mm)
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 64-LQFP (10 x 10 mm)
Maximum Clock Speed: 64 MHz
Flash Memory: 512KB (512K x 8)
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 100-LQFP (14x14 mm)
Series: SAM3U
USB: High-speed USB device with integrated transceiver
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 100-LQFP (14 x 14 mm)
Flash Memory: 128 KB (128K x 8)
USB: USB 2.0 High-Speed Device, 480 Mbps, embedded transceiver, 4 KB FIFO, up to 7 endpoints, dedicated DMA
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 144-LQFP (20x20 mm)
Series: SAM3U (AT91 SMART ARM-based)
Maximum Clock Speed: 96 MHz
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 144-LQFP (20x20 mm)
Series: SAM3X
Maximum Clock Speed: 84 MHz
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →
Microchip Technology
Package: 144-LQFP (20 x 20 mm)
Series: SAM3X/A (SAM3X)
Maximum Clock Speed: 84 MHz
بەراوردکردن لەگەڵ ATSAM3U4CA-AU →

ATSAM3U4C-AU

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 100-LQFP (14 x 14 mm)
Same SAM3U4C device family and 100-LQFP footprint; ordering-code detail differs by 0% in the core, Flash, and SRAM ratings.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ATSAM3U2CA-AU

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 100-LQFP (14 x 14 mm)
ARM Cortex-M3 revision 2.0 · 32-bit · 96 MHz · 128 KB (128K x 8) · 36 KB · Yes (MPU) · Thumb-2 · USB 2.0 High-Speed Device, 480 Mbps, embedded transceiver, 4 KB FIFO, up to 7 endpoints, dedicated DMA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATSAM3A4CA-AU

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 100-LQFP (14 x 14 mm)
ARM Cortex-M3 revision 2.0 · 32-bit · 84 MHz · 256 KB (2 x 128 KB banks) · FLASH · 64 KB (2 x 32 KB banks) · 1.62 V to 3.6 V · A/D 16x12-bit; D/A 2x12-bit

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATSAM3X4EA-AU

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 100-LQFP (14 x 14 mm)
ARM Cortex-M3 (revision 2.0) · 32-Bit · 84 MHz · 256 KB (256K x 8) · SAM3X · 144-LQFP (20x20 mm) · Surface Mount · CAN, EBI/EMI, Ethernet, I2C, IrDA, LIN, MMC, USB

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATSAM3X8EA-AU

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 100-LQFP (14 x 14 mm)
ARM Cortex-M3 revision 2.0 · 32-bit · 84 MHz · 512 KB (512K x 8) · 100 KB (100K x 8), dual bank · 1.62 V to 3.6 V (1.8 V / 2.5 V / 3.3 V) · 16-channel, 12-bit · 2-channel, 12-bit

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATSAM3U4CA-AU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type 32-bit ARM Flash microcontroller
Processor Core ARM Cortex-M3 revision 2.0
Maximum CPU Frequency 96 MHz
Instruction Set Thumb-2, 32-bit RISC
Embedded Flash Memory 256 KB
Flash Organization Dual-bank, 128-bit-wide access
Embedded SRAM 52 KB
Memory Protection Unit Yes
Operating Voltage 1.8 V or 3.3 V
USB Interface USB 2.0 device, 480 Mbps
USB FIFO 4 KB
USB Endpoints Up to 7 bidirectional endpoints
USART Count Up to 4
UART Count 1
TWI Interfaces Up to 2
SPI Interface 1
SSC Interface 1
HSMCI Controller 1
RTC Backup Current 0.6 µA
پاکێج 100-pin LQFP, 14 x 14 mm
جۆری دامەزراندن Surface mount
دۆخی چرخەی ژیان Active

ڕێنمایی ڕێکخستنی پینی ATSAM3U4CA-AU 100-pin lqfp, 14 x 14 mm

ڕێکخستنی پین بۆ ATSAM3U4CA-AU (پاکێجی 100-pin lqfp, 14 x 14 mm). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.

نەخشەی پینئاوتی پاکێجی 100-pin lqfp, 14 x 14 mm بۆ ATSAM3U4CA-AU

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ATSAM3U4CA-AU.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ATSAM3U4CA-AU گونجاوە بۆ 6 بەکارھێنانs: USB Connected Data Acquisition, Industrial HMI Controller, Sensor Hub and Edge Node, USB Peripheral and Dongle, Embedded Automation Controller, Battery-Powered Portable Instrument.

🖥️

USB Connected Data Acquisition

The ATSAM3U4CA-AU fits USB data-acquisition equipment that needs local signal processing without an external host processor. Its 96 MHz ARM Cortex-M3 core supports real-time filtering and control, while 256 KB of dual-bank Flash stores firmware and 52 KB of SRAM accommodates samples, protocol buffers, and acquisition state. The USB 2.0 device controller operates at 480 Mbps with a 4 KB FIFO and up to seven bidirectional endpoints. Designers can connect sensors through SPI, TWI, USART, or HSMCI while presenting a USB interface to a computer. Board routing must implement USB impedance control, protect the connector, and provide local decoupling.

🏭

Industrial HMI Controller

The ATSAM3U4CA-AU is appropriate for an industrial human-machine interface that coordinates displays, touch controls, communications, and machine-state monitoring. The 96 MHz Cortex-M3 core provides useful headroom for graphical refresh, event handling, and protocol processing, while the 52 KB SRAM reduces pressure on external memory in moderate interface designs. Up to four USARTs, two TWI channels, SPI, SSC, and HSMCI support displays, sensors, storage, and field equipment. For industrial deployment, isolate external interfaces as required, apply surge and ESD protection, and confirm the device temperature grade against the enclosure’s worst-case conditions.

🧩

Sensor Hub and Edge Node

A sensor hub built with the ATSAM3U4CA-AU can aggregate readings from multiple physical interfaces and present processed results over USB or serial links. Its 52 KB of SRAM supports packet staging and short-term data processing, and its 96 MHz core can combine protocol conversion, filtering, and control tasks. Two TWI interfaces suit low-speed sensors, SPI supports higher-rate devices, and the four USARTs handle external modules or gateways. The dual-bank Flash architecture is useful when a carefully designed update workflow keeps boot or recovery code separate from application firmware. Select external sensor, transceiver, and memory parts with voltage levels compatible with the 1.8 V or 3.3 V operating options.

🔧

USB Peripheral and Dongle

The ATSAM3U4CA-AU can serve as the core of a compact USB peripheral or protocol-conversion dongle because it integrates USB 2.0 device operation, substantial Flash, SRAM, and multiple serial interfaces in one package. The seven-endpoint capability allows several logical USB functions or transfer directions to coexist, while USART, SPI, and TWI bridges connect legacy or embedded subsystems. Its 96 MHz processing rate supports protocol framing, buffering, and real-time adaptation without a separate communications controller. Product-level compliance depends on the complete USB implementation, so designers should follow the controller guidance, validate descriptors and power behavior, and verify enumeration using the intended host environment.

⚙️

Embedded Automation Controller

The ATSAM3U4CA-AU suits compact embedded automation controllers that coordinate motors, sensors, operator interfaces, and remote communications. Its 96 MHz Cortex-M3 core provides deterministic control capability, while the USART, TWI, SPI, SSC, and HSMCI blocks connect motion controllers, position sensors, local storage, and external communications modules. The 256 KB Flash capacity can hold application logic and protocol handlers, and the 52 KB SRAM can support dual-bank firmware workflows. Engineering validation should cover output timing, brownout behavior, watchdog policy, ground-plane continuity, and protection from industrial transients. Firmware must also prevent peripheral contention and use a safe state when communications are interrupted.

📱

Battery-Powered Portable Instrument

The ATSAM3U4CA-AU can form the control core of a battery-powered portable instrument that balances processing performance with low-power peripheral operation. The 0.6 µA RTC backup current supports timekeeping when the main supply is removed, while software-controlled sleep modes can reduce active consumption between measurements. Its USB interface simplifies configuration and data export, and the 52 KB SRAM limits the need for external memory in compact designs. For battery products, calculate average current from active, idle, sleep, and USB-attached states; use regulator efficiency, wake latency, and battery capacity as explicit design inputs. The 1.8 V or 3.3 V operating options also require matching the selected power tree and level-shift requirements.

What is the ATSAM3U4CA-AU?
The ATSAM3U4CA-AU is a Microchip SAM3U-series 32-bit Flash microcontroller built around an ARM Cortex-M3 processor. It operates at up to 96 MHz and provides 256 KB of Flash, 52 KB of SRAM, USB 2.0 device support, and multiple serial interfaces in a 100-pin LQFP package. The manufacturer describes the part as an active SAM3U-family device suitable for embedded control and communications designs.
What are the key specifications of ATSAM3U4CA-AU?
The ATSAM3U4CA-AU combines a 96 MHz ARM Cortex-M3 core, 256 KB of dual-bank embedded Flash, 52 KB of SRAM, and a 100-pin 14 x 14 mm LQFP package. It supports 1.8 V or 3.3 V operation and includes USB 2.0 device support at 480 Mbps, a 4 KB FIFO, up to seven bidirectional endpoints, four USARTs, two TWI interfaces, SPI, SSC, HSMCI, and a low-power RTC.
Where can I download the ATSAM3U4CA-AU datasheet PDF?
The ATSAM3U4CA-AU datasheet can be accessed through Microchip’s official ATSAM3U4C product page or through the indexed datasheet links associated with this device. The manufacturer documentation should be the controlling reference for the complete 100-pin assignment, electrical limits, clock requirements, and package drawings. Search the exact ATSAM3U4CA-AU order code when matching documentation to the purchased configuration.
Where can I find the ATSAM3U4CA-AU pinout?
The ATSAM3U4CA-AU pinout is shown in the manufacturer datasheet and package documentation for the 100-LQFP, 14 x 14 mm device. Use that drawing to assign VDDBU, supply, ground, clock, debug, USB, and peripheral signals to the exact ordering code. The ATSAM3U4CA-AU is a 100-pin package, so a complete board symbol should expose all 100 physical pins rather than only the signals used by one application.
How much Flash and SRAM does the ATSAM3U4CA-AU have?
The ATSAM3U4CA-AU contains 256 KB of embedded Flash and 52 KB of SRAM. Its Flash uses a dual-bank organization with 128-bit-wide access and a memory accelerator. This combination supports embedded firmware, boot or supervisory code, communication buffers, display state, and real-time control data, while the dual-bank architecture can assist update designs when used according to Microchip’s documented procedure.
What peripherals are built into the ATSAM3U4CA-AU?
The ATSAM3U4CA-AU includes a USB 2.0 device controller, up to four USARTs, one UART, up to two TWI interfaces, one SPI interface, one SSC, and one HSMCI controller. The USB controller operates at 480 Mbps with a 4 KB FIFO and supports up to seven bidirectional endpoints. These resources allow one MCU to coordinate USB connectivity, sensor acquisition, external memory, and industrial serial equipment.
Is ATSAM3U4CA-AU suitable for USB data acquisition?
The ATSAM3U4CA-AU is suitable for USB-connected data acquisition because it combines a 96 MHz Cortex-M3 core, USB 2.0 device operation, 52 KB of SRAM, and serial peripherals in one package. Its 4 KB USB FIFO and support for seven bidirectional endpoints help organize USB traffic, while USART, SPI, TWI, and HSMCI channels can connect sensors and external storage. Board-level impedance and USB signal-integrity design remain essential.
Where can I buy ATSAM3U4CA-AU online?
Use the “Request a Quote” form on this page to request ATSAM3U4CA-AU availability, lead time, and a current quotation from XAIPART. Quote requests should identify the exact MPN ATSAM3U4CA-AU, the required package or packing configuration, and your target delivery quantity. Request current supply and lead-time confirmation directly through the form rather than relying on a static listing status.
What is the price of ATSAM3U4CA-AU?
The current ATSAM3U4CA-AU price is not stated as a fixed figure on this page because quotation-based procurement requires live inventory and quantity confirmation. Submit the ATSAM3U4CA-AU MPN through the “Request a Quote” form on this page. The request should include your order quantity, delivery destination, and preferred packing so the quotation can reflect the correct commercial configuration.
What is the lead time for ATSAM3U4CA-AU?
The ATSAM3U4CA-AU lead time should be confirmed through the “Request a Quote” form on this page. Lead time can vary with order quantity, factory availability, and the requested packing configuration. The device is listed as active, but current schedule confirmation is necessary for production planning. Include your forecast quantities and required delivery date in the request.
Is ATSAM3U4CA-AU in stock?
Current ATSAM3U4CA-AU stock should be requested through the “Request a Quote” form on this page rather than inferred from a catalog entry. Provide the exact MPN, quantity, package, and delivery location so XAIPART can confirm the current supply position. For production schedules, ask for both the initial allocation and the expected replenishment interval.
ATSAM3U4CA-AU vs ATSAM3X4EA-AU - which is better?
ATSAM3U4CA-AU is the appropriate choice when the design specifically targets the SAM3U family, its 256 KB Flash configuration, 52 KB SRAM, and established peripheral assignments. ATSAM3X4EA-AU is a useful family comparison, but peripheral mapping, memory organization, and device-support requirements must be checked before substitution. Choose the exact device only after reviewing the manufacturer pin, clock, and peripheral compatibility documentation.
What is the difference between ATSAM3U4CA-AU and ATSAM3U2CA-AU?
ATSAM3U4CA-AU provides 256 KB of embedded Flash, while the ATSAM3U2CA-AU is the lower-memory member of the same SAM3U family. Both are associated with the 96 MHz Cortex-M3 architecture and the 100-LQFP package family, but software memory maps, bootloader assumptions, and application code size can make them non-interchangeable in practice. Treat the ATSAM3U4CA-AU as the correct choice when its larger Flash capacity is required.
When should I choose ATSAM3U4CA-AU over ATSAM3X4EA-AU?
Choose ATSAM3U4CA-AU when maintaining the SAM3U-family hardware design, peripheral configuration, and 256 KB memory architecture is more important than evaluating a different SAM family. Its Cortex-M3 core, USB 2.0 device controller, dual-bank Flash, and 52 KB SRAM suit compact control, HMI, and data-acquisition products. Select ATSAM3X4EA-AU only after confirming its package pins, memory map, peripherals, and software support satisfy the target design.
Is ATSAM3U4CA-AU suitable for industrial HMI and automation?
The ATSAM3U4CA-AU fits industrial HMI and automation controllers that require a 96 MHz processor, 256 KB Flash, 52 KB SRAM, USB, and several serial interfaces. Its TWI, SPI, USART, SSC, and HSMCI resources can connect sensors, displays, storage, and field-bus transceivers. Validate operating-temperature limits, isolation strategy, surge protection, and EMC requirements separately for the finished industrial system.
What can replace ATSAM3U4CA-AU?
The closest documented alternatives are ATSAM3U4C-AU, ATSAM3U2CA-AU, ATSAM3A4CA-AU, ATSAM3X4EA-AU, and ATSAM3X8EA-AU, all listed as same-manufacturer candidates for comparison. No candidate should be treated as automatically interchangeable without checking the 100-pin assignment, memory map, voltage requirements, peripheral multiplexing, clock setup, and boot behavior. A footprint-compatible package alone does not guarantee functional drop-in replacement.

داتای سەرچاوەی ئەندازیاری بۆ ATSAM3U4CA-AU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ATSAM3U4CA-AU when the design requires a 96 MHz ARM Cortex-M3 MCU with 256 KB dual-bank Flash, 52 KB SRAM, USB 2.0 device support, and a broad mix of serial interfaces in a 100-pin LQFP. ATSAM3U4C-AU is the closest same-family selection and should be preferred when the exact ordering-code details need clarification. ATSAM3U2CA-AU makes sense only when its smaller Flash capacity satisfies the firmware and the reduced memory budget is acceptable. ATSAM3A4CA-AU may fit a different SAM application, but its pin multiplexing, memory map, and peripherals require explicit verification. ATSAM3X4EA-AU is appropriate when its additional family features are needed and the application is rebuilt for the SAM3X peripheral arrangement. ATSAM3X8EA-AU offers a larger-memory family option but introduces a significant Flash-capacity difference. In every case, verify package pins, voltage, clocking, boot configuration, peripheral functions, and software support before treating a candidate as a drop-in replacement.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ATSAM3U4C-AU ATSAM3U2CA-AU ATSAM3A4CA-AU ATSAM3X4EA-AU ATSAM3X8EA-AU
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm)

جیاکەرەوە سەرەکییەکان

  • Higher Flash capacity within the compared SAM3U4C selection (بەراورد بەATSAM3U2CA-AU)
  • Same-family processor and peripheral architecture (بەراورد بەATSAM3X4EA-AU)
  • USB device integration without an external controller (بەراورد بەATSAM3A4CA-AU)
  • Broad serial-interface integration in one device (بەراورد بەATSAM3U4C-AU)

تێبینییەکانی دیزاین

Assign the ATSAM3U4CA-AU to either the 1.8 V or 3.3 V operating domain consistently across its supply pins and connected peripherals. Place the manufacturer-recommended bypass capacitors immediately beside the relevant supply and ground pins, with short, low-inductance connections. Separate analog, digital, and interface return currents where the board architecture permits, and verify startup, brownout, USB-attachment, and peripheral-load conditions before releasing the power design.

Treat the 100-pin LQFP footprint as a complete 100-pad symbol and use the manufacturer package drawing as the dimensional authority. Check pad width, length, pitch, pin-1 orientation, and exposed thermal behavior against the chosen land pattern. Avoid routing split or interrupted ground planes beneath the device, and fan out supply connections on multiple sides when the pin arrangement permits. This reduces inductance and makes production-package changes easier to manage.

Route USB D+ and D− as a short, impedance-controlled differential pair over a continuous reference plane, with compliant connectors, protection devices, and placement consistent with the controller guidance. Keep clock and high-speed memory traces away from noisy switching nodes, use appropriate source termination where required, and test timing with the intended peripherals enabled. The MCU’s USB controller capability does not by itself guarantee system-level USB compliance.

Do not assume that a device in the same 100-LQFP package is automatically interchangeable. Review the alternate device’s pin names, peripheral multiplexing, memory organization, boot configuration, voltage limits, and development-tool support. The ATSAM3U4C-AU is the closest same-family selection; ATSAM3U2CA-AU reduces available Flash, while ATSAM3A4CA-AU and ATSAM3X devices require deliberate firmware and hardware review.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The device is listed as active, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were found in the indexed product information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-04 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ATSAM3U4CA-AU ATSAM3U4CA-AU datasheet ATSAM3U4CA-AU datasheet pdf ATSAM3U4CA-AU pinout ATSAM3U4CA-AU specifications ATSAM3U4CA-AU equivalent ATSAM3U4CA-AU replacement ATSAM3U4CA-AU cross reference ATSAM3U4CA-AU price ATSAM3U4CA-AU stock Microchip ATSAM3U4CA-AU ATSAM3U4CA-AU 96MHz Cortex-M3 ATSAM3U4CA-AU 256KB Flash ATSAM3U4CA-AU 100-LQFP pinout ATSAM3U4CA-AU USB application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology ATSAM3U4CA-AU ATSAM3U4C ATSAM3U2CA-AU ATSAM3A4CA-AU ATSAM3X4EA-AU ATSAM3X8EA-AU ARM Cortex-M3 ARM Cortex-M3 revision 2.0 Thumb-2 instruction set 32-bit RISC processor SAM3U microcontroller family Flash microcontroller embedded microcontroller semiconductor dual-bank Flash memory embedded SRAM Memory Protection Unit USB 2.0 device controller 480 Mbps USB USART TWI SPI SSC HSMCI 100-LQFP package LQFP family surface mount technology low-power RTC dual-bank firmware update industrial HMI USB data acquisition
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ