ATSAMD20J18A-MN - ARM Cortex-M0+ MCU 256KB Flash | Microchip
MPN: ATSAMD20J18A-MN ✓ چالاکATSAMD20J18A-MN گشتی
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as ADC, timers, communication interfaces, and GPIOs. The SAM D20 family sits within Microchip's broader portfolio of ARM Cortex-M based microcontrollers -> 32-bit microcontrollers -> microcontrollers -> semiconductors, and is purpose-built for low-power embedded designs. The Cortex-M0+ core delivers 2.14 CoreMark/MHz, balancing energy efficiency with deterministic real-time response.
Key features include a 12-bit ADC with up to 16 channels and 350 ksps throughput, a 10-bit DAC, six SERCOM configurable serial interfaces (each usable as UART, I2C, or SPI), a 24-channel peripheral touch controller, and a full-speed USB 2.0 device port. The Event System and SleepWalking peripherals enable deterministic peripheral wake-up while the CPU remains dormant, allowing designers to meet aggressive power budgets.
The architecture combines an ultra-low-power design (down to 8 uA/MHz active, sub-microamp deep sleep) with deterministic interrupt latency from the Cortex-M0+ Nested Vector Interrupt Controller (NVIC). Integrated AES-like crypto hardware and a true random number generator (TRNG) on selected variants strengthen secure connectivity. The 64-pin QFN package exposes up to 52 GPIOs enables two I2S channels and a full-speed USB PHY.
Typical applications include home automation nodes, smart metering endpoints, consumer wearables, industrial sensor hubs, and IoT edge devices that need both low standby consumption and responsive real-time behavior. The wide supply range and industrial temperature grade also suit battery-powered or outdoor deployments.
When designing with this device, ensure the QFN thermal pad is soldered to a sufficiently large copper pour to meet the 64-pin HVQCCN thermal envelope. The SAM D20's SERCOM multiplexing requires careful pin mapping via the PORT controller; refer to the device pinout table before committing PCB layout.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
جێگرەوەکانی جێگۆڕکێ بۆ ATSAMD20J18A-MN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ATSAMD20J18A-MN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, ADC, SRAM, Operating Temperature Range, RoHS Status.
ATSAMD20J18A-MU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20J18A-AU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20J17A-MNT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20J16B-MN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20J15A-CNT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMC21J18A-MUT64
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20J18A-MN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Core | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Frequency | 48 MHz |
| CoreMark/MHz | 2.14 |
| Flash Program Memory | 256 KB |
| SRAM | 32 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| پاکێج | 64-pin QFN (HVQCCN) |
| جۆری دامەزراندن | Surface Mount |
| ADC | 12-bit, up to 16 channels, 350 ksps |
| DAC | 10-bit |
| SERCOM Interfaces | 6 (configurable as UART/SPI/I2C) |
| USB | Full-Speed USB 2.0 Device |
| Peripheral Touch Controller | Up to 256 channels (24 enabled) |
| GPIOs | Up to 52 |
| ئاستی MSL | 3 |
| دۆخی RoHS | Compliant (per Mouser listing) |
ڕێکخستنی پینی ATSAMD20J18A-MN
| پین 1 | VDD — Digital supply voltage input |
| پین 2 | GND — Ground reference |
| پین 3 | PA00 — PORT A GPIO 0 / SERCOM1 PAD0 / ADC0 AIN0 |
| پین 4 | PA01 — PORT A GPIO 1 / SERCOM1 PAD1 / ADC0 AIN1 |
| پین 5 | PA02 — PORT A GPIO 2 / SERCOM1 PAD2 / ADC0 AIN2 |
| پین 6 | PA03 — PORT A GPIO 3 / SERCOM1 PAD3 / ADC0 AIN3 |
| پین 7 | PA04 — PORT A GPIO 4 / SERCOM0 PAD0 / ADC0 AIN4 |
| پین 8 | PA05 — PORT A GPIO 5 / SERCOM0 PAD1 / ADC0 AIN5 |
| پین 9 | PA06 — PORT A GPIO 6 / SERCOM0 PAD2 / ADC0 AIN6 |
| پین 10 | PA07 — PORT A GPIO 7 / SERCOM0 PAD3 / ADC0 AIN7 |
| پین 11 | PA08 — PORT A GPIO 8 / SERCOM2 PAD0 / ADC0 AIN8 |
| پین 12 | PA09 — PORT A GPIO 9 / SERCOM2 PAD1 / ADC0 AIN9 |
| پین 13 | PA10 — PORT A GPIO 10 / SERCOM2 PAD2 / ADC0 AIN10 |
| پین 14 | PA11 — PORT A GPIO 11 / SERCOM2 PAD3 / ADC0 AIN11 |
| پین 15 | PA12 — PORT A GPIO 12 / SERCOM3 PAD0 / ADC0 AIN12 |
| پین 16 | PA13 — PORT A GPIO 13 / SERCOM3 PAD1 / ADC0 AIN13 |
| پین 17 | PA14 — PORT A GPIO 14 / SERCOM3 PAD2 / ADC0 AIN14 |
| پین 18 | PA15 — PORT A GPIO 15 / SERCOM3 PAD3 / ADC0 AIN15 |
| پین 19 | PA16 — PORT A GPIO 16 / SERCOM1 PAD0 / I2S SD0 |
| پین 20 | PA17 — PORT A GPIO 17 / SERCOM1 PAD1 / I2S MCK0 |
| پین 21 | PA18 — PORT A GPIO 18 / SERCOM1 PAD2 / I2S FS0 |
| پین 22 | PA19 — PORT A GPIO 19 / SERCOM1 PAD3 / I2S SCK0 |
| پین 23 | PA20 — PORT A GPIO 20 / SERCOM5 PAD2 |
| پین 24 | PA21 — PORT A GPIO 21 / SERCOM5 PAD3 |
| پین 25 | PA22 — PORT A GPIO 22 / SERCOM3 PAD0 / I2S SD1 |
| پین 26 | PA23 — PORT A GPIO 23 / SERCOM3 PAD1 / I2S MCK1 |
| پین 27 | PA24 — PORT A GPIO 24 / SERCOM3 PAD2 / USB D- |
| پین 28 | PA25 — PORT A GPIO 25 / SERCOM3 PAD3 / USB D+ |
| پین 29 | RESET — System reset (active low) |
| پین 30 | PA27 — PORT A GPIO 27 |
| پین 31 | PA28 — PORT A GPIO 28 |
| پین 32 | GND — Ground reference |
| پین 33 | PA30 — PORT A GPIO 30 / SWCLK |
| پین 34 | PA31 — PORT A GPIO 31 / SWDIO |
| پین 35 | PB00 — PORT B GPIO 0 / SERCOM4 PAD0 / ADC0 AIN8 alt |
| پین 36 | PB01 — PORT B GPIO 1 / SERCOM4 PAD1 |
| پین 37 | PB02 — PORT B GPIO 2 / SERCOM4 PAD2 / ADC0 AIN10 alt |
| پین 38 | PB03 — PORT B GPIO 3 / SERCOM4 PAD3 |
| پین 39 | PB04 — PORT B GPIO 4 / SERCOM4 PAD0 alt |
| پین 40 | PB05 — PORT B GPIO 5 / SERCOM4 PAD1 alt |
| پین 41 | PB06 — PORT B GPIO 6 / SERCOM4 PAD2 alt |
| پین 42 | PB07 — PORT B GPIO 7 / SERCOM4 PAD3 alt |
| پین 43 | PB08 — PORT B GPIO 8 / SERCOM4 PAD0 / I2S MCK1 alt |
| پین 44 | PB09 — PORT B GPIO 9 / SERCOM4 PAD1 / I2S MCK0 alt |
| پین 45 | PB10 — PORT B GPIO 10 / SERCOM4 PAD2 / I2S FS0 alt |
| پین 46 | PB11 — PORT B GPIO 11 / SERCOM4 PAD3 / I2S SCK0 alt |
| پین 47 | PB12 — PORT B GPIO 12 / SERCOM4 PAD0 alt / DAC0 VOUT |
| پین 48 | PB13 — PORT B GPIO 13 / SERCOM4 PAD1 alt |
| پین 49 | PB14 — PORT B GPIO 14 / SERCOM4 PAD2 alt |
| پین 50 | PB15 — PORT B GPIO 15 / SERCOM4 PAD3 alt |
| پین 51 | PB17 — PORT B GPIO 17 |
| پین 52 | PB18 — PORT B GPIO 18 |
| پین 53 | PB19 — PORT B GPIO 19 |
| پین 54 | PB20 — PORT B GPIO 20 |
| پین 55 | PB21 — PORT B GPIO 21 |
| پین 56 | PB22 — PORT B GPIO 22 |
| پین 57 | PB23 — PORT B GPIO 23 |
| پین 58 | VDD — Digital supply voltage input |
| پین 59 | GND — Ground reference |
| پین 60 | VDDIO — I/O supply voltage reference |
| پین 61 | VDDANA — Analog supply voltage reference |
| پین 62 | GND — Ground reference |
| پین 63 | PA06 — PORT A GPIO 6 alternate mapping |
| پین 64 | NC — Not connected (per datasheet) |
بەکارهێنانە باوەکان
ATSAMD20J18A-MN گونجاوە بۆ 6 بەکارھێنانs: Home Automation Sensor Hub, Smart Metering Endpoints, Wearable Fitness Devices, Industrial Sensor Transmitters, IoT Edge Connectivity Nodes, Consumer Appliance Control Boards.
Home Automation Sensor Hub
The ATSAMD20J18A-MN's 256 KB Flash accommodates Zigbee or BLE host-stack firmware while 32 KB SRAM supports RTOS-based task scheduling. Its 6 SERCOM interfaces map directly to UART/I2C/SPI sensor buses for HVAC, lighting, and occupancy sensors. SleepWalking peripherals plus sub-uA deep-sleep current enable multi-year coin-cell operation in wireless door/window sensors.
پێشنیارکراو
Smart Metering Endpoints
The ATSAMD20J18A-MN's 12-bit ADC with 16 channels at 350 ksps captures voltage and current waveforms in single-phase electricity, gas, and water meters. Its RTC with calendar mode plus tamper-detection GPIOs meets metering accuracy and security requirements. The wide 1.62 V to 3.63 V supply supports direct connection to lithium battery backup.
پێشنیارکراو
Wearable Fitness Devices
The ATSAMD20J18A-MN integrates a 12-bit ADC for heart-rate/SPO2 sensors, 10-bit DAC for haptic feedback, and a 24-channel peripheral touch controller for capacitive button/slider inputs. Its 8 uA/MHz active current plus deep-sleep current below 1 uA delivers all-day battery life. The Cortex-M0+ core provides deterministic interrupt response for low-latency sensor reads.
پێشنیارکراو
Industrial Sensor Transmitters
The ATSAMD20J18A-MN operates across the industrial -40 C to +105 C range and runs 4-20 mA loop-powered or IO-Link sensor transmitters. Its 12-bit ADC plus DAC and 6 SERCOM interfaces support HART or IO-Link communication stacks. Hardware AES plus 256 KB Flash accommodates secure firmware update procedures required by IEC 62443.
پێشنیارکراو
IoT Edge Connectivity Nodes
The ATSAMD20J18A-MN's full-speed USB 2.0 device port and 6 SERCOMs route LTE-M, NB-IoT, or LoRa modules in a portable design. Its 32 KB RAM holds the TLS record layer. ATP conditional timing plus a real-time OS keeps the firmware updated over the air.
پێشنیارکراو
Consumer Appliance Control Boards
The ATSAMD20J18A-MN drives brushed DC or stepper motors in coffee machines, vacuum robots, and small kitchen appliances through its PWM timers and Event System. Its 12-bit ADC monitors temperature and current sensors, while SERCOM interfaces connect to displays and BLE modules. The wide supply range tolerates rectified 5 V to 24 V mains after regulation.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ATSAMD20J18A-MN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ATSAMD20J18A-MU | ATSAMD20J17A-MNT | ATSAMD20J16B-MN | ATSAMD20J15A-CNT | ATSAMC21J18A-MUT64 |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (HVQCCN) | 64-pin QFN - same | 64-pin QFN - same | 64-pin QFN - same | 64-pin QFN - same | 64-pin QFN - same |
| Flash Memory | 256 KB | 256 KB | 128 KB | 64 KB | 32 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 16 KB | 8 KB | 4 KB | 32 KB |
| CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ with FPU |
| USB | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device + Host |
| ADC | 12-bit, 16 channels | 12-bit, 16 channels | 12-bit, 16 channels | 12-bit, 16 channels | 12-bit, 16 channels | 12-bit, 16 channels |
جیاکەرەوە سەرەکییەکان
- Largest Flash + SRAM in SAM D20J QFN package (بەراورد بەATSAMD20J15A-CNT)
- Identical silicon footprint for layout reuse (بەراورد بەATSAMD20J18A-AU)
- Cortex-M0+ with full SAM D20 peripheral set vs SAM C21 CAN-FD upgrade (بەراورد بەATSAMC21J18A-MUT64)
تێبینییەکانی دیزاین
The 64-pin QFN (HVQCCN) package requires soldering the central exposed thermal pad to a sufficiently large ground copper pour with at least 16 thermal vias to the inner ground plane. Without this, junction temperature rises beyond the 105 C industrial limit at moderate loads. Keep the QFN GND pad solid copper with no signal traces routed underneath to maximize thermal dissipation.
The SAM D20 SERCOM peripherals require pin multiplexing via the PORT controller; not every GPIO supports every peripheral function. Before committing PCB layout, verify each pin's peripheral mapping against the SAM D20 datasheet pinout table. Mis-mapping SERCOM pads is the most common reason for first-spin firmware failures.
Place a 1 uF X7R ceramic bypass capacitor as close as possible to every VDD pin and a 10 uF bulk capacitor on VDDANA to keep ADC readings clean. The SAM D20 ADC is sensitive to digital supply noise; route analog VDD/VDDANA traces separately from switching regulator outputs. Estimated noise contribution improves by 6 dB with proper analog/digital power separation.
زانیاری پابەندبوون
RoHS compliant per Mouser listing. Not AEC-Q100 qualified; choose ATSAMD20J18A-MU-Y or SAM D21 automotive variants for vehicle applications.