ATTINY1634-MN - 12MHz 8-bit AVR 16KB MCU | Microchip Technology
MPN: ATTINY1634-MN ✓ چالاکATTINY1634-MN گشتی
An 8-bit AVR microcontroller is a compact embedded-control device that executes instructions using an enhanced RISC core, typically approaching 1 MIPS per MHz. The ATtiny family sits within the broader hierarchy of embedded processors, microcontrollers, embedded controllers and semiconductors. The ATTINY1634 is designed for low-power control tasks where local processing, serial communication, timing and mixed-signal control are needed without a high-cost MCU platform.
Key device capabilities include a 12 MHz maximum clock, 16 KB Flash, 256 B EEPROM, 1 KB SRAM, 18 general-purpose I/O lines, 32 general-purpose working registers, one 8-bit timer/counter, one 16-bit timer/counter, two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface, I2C slave support and internal and external interrupts. These resources make the MCU suitable for compact control boards, industrial modules and embedded peripherals.
The AVR enhanced RISC architecture provides an instruction-oriented balance between processing throughput and power efficiency. At the rated 12 MHz operating point, the architecture can approach 1 MIPS, while the low-power CMOS design supports applications that alternate between active processing and reduced-power operating states. The combination of dual USARTs, USI and I2C allows the device to bridge several common embedded serial interfaces without requiring large numbers of external peripheral ICs.
Typical uses include industrial sensing and control, compact serial gateways, sensor-hub controllers, battery-powered instrumentation, communication modules and small automation nodes. Its 18 I/O lines also permit direct interface connections to sensors, displays, relays and digital logic. The 20-QFN exposed-pad package supports dense PCB layouts, although careful thermal-pad soldering and layout practices are important for reliable assembly.
Designers should verify the complete pin-assignment table in the manufacturer datasheet before routing the PCB, particularly for the exposed pad, power pins, reset and communications functions. Decoupling requirements, clock stability, programming access, I2C address configuration and USART logic levels should also be checked against the device documentation and the selected operating voltage.
This product page consolidates the exact ATTINY1634-MN technical identity, verified listing information, package details and engineering guidance into one focused reference for embedded-system design.
جێگرەوەکانی جێگۆڕکێ بۆ ATTINY1634-MN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
ATTINY1634-15XZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ATTINY1634-MN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 8-bit AVR microcontroller |
| Architecture | AVR enhanced RISC |
| زۆرترین فرێکوێنسیی کاتژمێر | 12 MHz |
| Flash Memory | 16 KB (16K x 8) |
| EEPROM Memory | 256 B |
| SRAM | 1 KB |
| General-Purpose I/O Lines | 18 |
| General-Purpose Working Registers | 32 |
| Timer/Counters | One 8-bit and one 16-bit timer/counter |
| Serial Interfaces | Two USARTs, USI and I2C slave |
| Operating Voltage Range | 1.8 V to 5.5 V |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +105 °C (TA) |
| پاکێج | 20-QFN exposed-pad, 4 x 4 mm |
| جۆری دامەزراندن | Surface mount |
| Core Processor | AVR 8-bit |
| Instruction Throughput | Approaching 1 MIPS per MHz |
| دۆخی RoHS | Compliant |
ڕێنمایی ڕێکخستنی پینی ATTINY1634-MN 20-qfn exposed-pad, 4 x 4 mm
ڕێکخستنی پین بۆ ATTINY1634-MN (پاکێجی 20-qfn exposed-pad, 4 x 4 mm). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ATTINY1634-MN.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ATTINY1634-MN گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor and Control Node, Serial Communication Gateway, Battery-Powered Instrumentation, Compact Motor and Actuator Controller, Connected IoT Sensor Module, Automated Test and Measurement Equipment.
Industrial Sensor and Control Node
The ATTINY1634-MN fits compact industrial sensing nodes because it combines 18 general-purpose I/O lines, a 12 MHz AVR core, two USARTs and I2C slave support in a 4 x 4 mm 20-QFN package. It can acquire sensor inputs, apply thresholding or filtering, control discrete outputs and forward measurements through a serial uplink. The 16 KB Flash supports a dedicated control and communications firmware, while 1 KB SRAM is adequate for compact protocol buffers and working variables. At a 1.8 V to 5.5 V supply range, the device accommodates industrial interface levels, although level translation and isolation may still be required. Firmware should use the internal or external clock configuration appropriate to accuracy, latency and power objectives.
پێشنیارکراو
Serial Communication Gateway
The ATTINY1634-MN is appropriate for a small serial gateway because it provides two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface and I2C slave capability. Firmware can bridge a local sensor bus to an upstream host, validate incoming frames, maintain counters and report status without a larger communications processor. Its 16 KB Flash provides room for protocol conversion and diagnostics, while the 1 KB SRAM can support bounded buffering. The two USARTs permit simultaneous host and field-device links when the selected pin multiplexing and peripheral configuration support the intended traffic. Clock accuracy, baud-rate tolerance, logic thresholds and connector protection should be validated for each communication standard.
پێشنیارکراو
Battery-Powered Instrumentation
The ATTINY1634-MN can serve as the control core in battery-powered instrumentation because it is a low-power CMOS 8-bit AVR microcontroller that operates from 1.8 V to 5.5 V. Its 12 MHz maximum clock provides ample throughput for sampling, control and low-volume serial reporting, while sleep modes can reduce consumption between measurements. The device offers 18 I/O lines for sensor enables, status indicators and measurement triggers, plus two USARTs for configuration and data transfer. Firmware should measure the complete system sleep current, disable unused peripherals and select the lowest practical clock rate. The 16 KB Flash limit must also be considered when combining logging, communications and safety diagnostics.
پێشنیارکراو
Compact Motor and Actuator Controller
The ATTINY1634-MN is suitable for compact actuator-control modules where a small controller must coordinate inputs, timers and external drivers. Its 18 general-purpose I/O lines can handle position sensors, limit switches, status LEDs and driver-control signals, while the 8-bit and 16-bit timers support event counting, timing and periodic control tasks. The 12 MHz AVR core and 16 KB Flash are sufficient for deterministic supervisory logic, but motor transients and inductive loads require suitable driver stages, flyback paths, bulk capacitance and protection. The MCU should not directly switch high-current motor windings unless its absolute maximum ratings explicitly permit the application. Firmware should include startup limits and fault handling, and the exposed pad must be connected according to the package guidance.
پێشنیارکراو
Connected IoT Sensor Module
The ATTINY1634-MN fits connected IoT sensor modules that need local sensing, protocol handling and simple control before data reaches a wireless companion. Its 18 I/O lines can interface with environmental or motion sensors, the two USARTs support low-rate telemetry and configuration, and the USI provides additional serial flexibility. The 1 KB SRAM and 16 KB Flash favor event-based rather than buffered high-bandwidth workloads, making the controller effective as a sensor-hub front end rather than a multimedia processor. A 1.8 V operating configuration can reduce power use when the connected module supports it. Firmware should define retry behavior, sensor timeout handling and low-power wake logic, while the PCB should isolate sensitive analog inputs from switching and radio circuitry.
پێشنیارکراو
Automated Test and Measurement Equipment
The ATTINY1634-MN can coordinate low-level test and measurement fixtures where sequencing, stimulus control and host communication are required. Two USARTs allow separate control and logging channels, the timers support accurate event timing and the 18 I/O lines can control relays, digital stimulus lines and status indicators. Firmware can execute test steps, record pass or fail results and report them to a host controller. Its 16 KB Flash is appropriate for moderate test-sequence logic, while the 1 KB SRAM limits large result buffering. The 1.8 V to 5.5 V operating range supports different fixture architectures, but signal conditioning, protection and grounding remain essential. Calibration data and fault checks should be implemented outside the MCU where greater storage or precision is needed.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ATTINY1634-MN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ATTINY1634-15XZ |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-QFN exposed-pad, 4 x 4 mm | 20-QFN exposed-pad, 4 x 4 mm |
| Core | AVR 8-bit | AVR 8-bit |
جیاکەرەوە سەرەکییەکان
- Compact communication-rich AVR controller (بەراورد بەATTINY1634-15XZ)
- Broad operating-voltage range (بەراورد بەATTINY1634-15XZ)
- Integrated timing and communication resources (بەراورد بەATTINY1634-15XZ)
تێبینییەکانی دیزاین
Route the ATTINY1634-MN power and ground pins using the manufacturer recommended land pattern, and connect the 20-QFN exposed pad according to the package guidance. Place the required decoupling capacitors close to their associated supply pins. Keep sensitive analog inputs away from switching nodes and high-current return paths to reduce coupled noise and ground bounce.
Follow the manufacturer clock recommendations when using an external oscillator, and keep the clock path short and physically separated from noisy signals. Confirm programming-test access, reset behavior and debug considerations before fixing the layout. If the I2C or USART traces leave the board, route them away from motor drives and switching-converter power loops.
The 1.8 V to 5.5 V operating range supports flexible rail selection, but the complete design must respect the limits of every attached peripheral and I/O pin. Define valid logic levels for each powered state, especially during startup and partial shutdown. Use the low-power modes only after verifying wake sources, clock-restart timing and the maximum interrupt latency required by the application.
Do not treat a related ATtiny1634 order code as an automatically approved drop-in replacement. Before substitution, compare the exact package drawing, exposed-pad connection, pin names, memory map, clock limits, peripheral multiplexing and interrupt vectors. Firmware that depends on the ATTINY1634-MN pin configuration should also be recompiled and regression-tested against the selected replacement.
زانیاری پابەندبوون
The Microchip product listing identifies the ATTINY1634-MN as RoHS compliant. No definitive REACH, AEC-Q100, lead-free, halogen-free or conflict-minerals declaration was established for this orderable part.