CY7C68301B-56LFXC - USB 2.0 ATA Bridge | Infineon
MPN: CY7C68301B-56LFXC ✓ چالاکCY7C68301B-56LFXC گشتی
A USB-to-ATA bridge is an interface controller that translates USB transactions into ATA commands and returns ATA responses through USB. These devices are used to connect USB storage systems to embedded computers, industrial equipment, test systems, and legacy storage peripherals. The CY7C68301B belongs to the EZ-USB AT2LP product family, combining a full-speed or high-speed USB bridge with ATA interface logic in one integrated circuit.
The device's defining specifications are its USB 2.0 ATA bridge function, 56-QFN package, and 8 mm by 8 mm body size. A comparison associated with the part lists an operating-voltage range of 3.15 V to 3.45 V and a temperature grade beginning at 0 degrees Celsius. The QFN package supports compact PCB layouts while exposing the bridge's power, USB, ATA, and control connections through a high pin count.
The CY7C68301B is intended for systems that need a dedicated USB storage interface rather than a general-purpose host controller. Its USB side connects to an external host, while the ATA side connects to compatible storage devices. The bridge architecture allows existing ATA/ATAPI storage subsystems to be accessed through a USB connection without implementing the full storage stack in host firmware.
Typical uses include USB-connected embedded storage, industrial data-acquisition equipment, legacy disk systems, test and measurement fixtures, and portable computing products. System designers should match the power rails, USB signaling requirements, ATA connector arrangement, clocking, and firmware configuration to the manufacturer datasheet before laying out the PCB.
Because the package uses a dense 56-pin QFN footprint, PCB planning requires careful escape routing and uninterrupted ground-plane placement. The manufacturer datasheet should be used for the authoritative pin assignments, exposed-pad connection, decoupling requirements, clock source, and ATA interface details. This page also compares related EZ-USB AT2LP devices and highlights where a different bridge variant may require design review.
For a new USB-to-ATA design, the CY7C68301B is most relevant when its documented USB, ATA, voltage, temperature, and package requirements match the target system. For an existing board, verify that the footprint, exposed pad, signal functions, firmware configuration, and electrical limits remain unchanged before considering a related bridge as a replacement.
جێگرەوەکانی جێگۆڕکێ بۆ CY7C68301B-56LFXC — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ CY7C68301B-56LFXC (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
CY7C68300C-56LFXC
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →CY7C68320-56LFXC
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →CY7C68301B-56LFXC تایبەتمەندییەکان
| Device Type | USB 2.0 to ATA/ATAPI bridge controller |
| USB Version | USB 2.0 |
| ATA Interface | ATA/ATAPI |
| Operating Voltage Range | 3.15 V to 3.45 V |
| پاکێج | 56-QFN, 8 mm x 8 mm |
| ژمارەی پین | 56 pins |
| جۆری دامەزراندن | Surface mount |
| Minimum Stated Temperature | 0 degrees Celsius |
| Product Family | EZ-USB AT2LP |
| Host Interface | USB |
| Storage Interface | ATA/ATAPI |
ڕێنمایی ڕێکخستنی پینی CY7C68301B-56LFXC 56-qfn, 8 mm x 8 mm
ڕێکخستنی پین بۆ CY7C68301B-56LFXC (پاکێجی 56-qfn, 8 mm x 8 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ CY7C68301B-56LFXC.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
CY7C68301B-56LFXC گونجاوە بۆ 6 بەکارھێنانs: Embedded USB Storage Adapter, Industrial Data-Acquisition System, Portable Measurement and Logging Equipment, Legacy ATA Test Fixture, USB Media Backup Appliance, Data Acquisition and Storage Gateway.
Embedded USB Storage Adapter
The CY7C68301B-56LFXC fits an embedded USB storage adapter because it provides a dedicated USB 2.0 host interface and ATA/ATAPI device interface. According to the manufacturer datasheet, the bridge operates from 3.15 V to 3.45 V and is packaged in a 56-QFN measuring 8 mm by 8 mm. Place the IC between the USB connector and an ATA-compatible storage device, then validate enumeration, command translation, media access, and suspend behavior with the target drive. The compact package saves board area, but its 56-terminal footprint requires careful fanout, exposed-pad handling, and short USB signal routing.
پێشنیارکراو
Industrial Data-Acquisition System
The CY7C68301B-56LFXC is useful when an industrial acquisition system must retain ATA or ATAPI storage while presenting a USB interface to a host computer. According to the manufacturer datasheet, its USB 2.0 and ATA/ATAPI interfaces provide the required protocol bridge, while its 3.15 V to 3.45 V operating range defines the core supply requirement. The bridge can isolate storage traffic from the host-facing control path and support acquisition media, diagnostics, or logged data. Confirm that the enclosure, drive interface, temperature grade, and industrial power requirements remain within the complete device specification.
پێشنیارکراو
Portable Measurement and Logging Equipment
The CY7C68301B-56LFXC fits portable measurement equipment that stores captured data on an ATA-compatible medium and transfers it through USB. According to the manufacturer datasheet, the device combines USB 2.0 and ATA/ATAPI functions in one 56-QFN package, reducing the number of separate interface components in a compact design. Place the bridge near the storage connector and USB port, then control power states to prevent unintended media access. Designers should account for the 3.15 V to 3.45 V supply range and verify the exact temperature grade against the portable equipment's environmental requirements.
پێشنیارکراو
Legacy ATA Test Fixture
The CY7C68301B-56LFXC can serve as the USB-to-storage interface in a fixture designed to exercise ATA or ATAPI equipment. According to the manufacturer datasheet, the bridge supports USB 2.0 on the host side and ATA/ATAPI on the device side, enabling a modern USB test computer to communicate with legacy storage hardware. Use the bridge to reduce the need for a full legacy controller in the fixture. Validate command behavior, transfer timing, power sequencing, and signal termination against the particular drive or target system before automating production tests.
پێشنیارکراو
USB Media Backup Appliance
The CY7C68301B-56LFXC is appropriate for a compact USB media backup appliance that exposes ATA/ATAPI storage through a USB 2.0 connection. According to the manufacturer datasheet, the 56-QFN device provides the complete protocol bridge while operating from 3.15 V to 3.45 V. Position the device to keep USB traces short and provide stable ATA signal routing to the storage connector. The design must support the target drive's power, startup, and media-change requirements, and it should implement explicit host-controlled power sequencing to avoid unexpected drive initialization.
پێشنیارکراو
Data Acquisition and Storage Gateway
The CY7C68301B-56LFXC can bridge a storage subsystem to an external computing host in a data-acquisition gateway. According to the manufacturer datasheet, the USB 2.0 and ATA/ATAPI interfaces support a dedicated storage path while the 56-QFN, 8 mm by 8 mm package limits board footprint. The bridge may store buffered measurements or provide access to an attached legacy disk. Validate sustained-transfer behavior, USB enumeration, drive compatibility, and the system's complete temperature requirement. Correct power sequencing and exposed-pad thermal design are especially important in compact gateways with limited airflow.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ CY7C68301B-56LFXC — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | CY7C68300C-56LFXC | CY7C68320-56LFXC |
|---|---|---|---|
| Package | 56-QFN (8x8 mm) | 56-QFN (8x8 mm) | 56-QFN (8x8 mm) |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Device Category | USB 2.0 to ATA/ATAPI bridge | EZ-USB AT2LP USB 2.0 bridge | EZ-USB AT2LP USB 2.0 to ATA/ATAPI bridge |
| Pin Count | 56 pins | 56 pins | 56 pins |
| Package Dimensions | 8 mm x 8 mm | 8 mm x 8 mm | 8 mm x 8 mm |
| USB Interface | USB 2.0 | USB 2.0 | USB 2.0 |
| Product Family | EZ-USB AT2LP | EZ-USB AT2LP | EZ-USB AT2LP |
جیاکەرەوە سەرەکییەکان
- Documented USB 2.0 to ATA/ATAPI bridge function (بەراورد بەCY7C68300C-56LFXC)
- Compact 8 mm by 8 mm package (بەراورد بەCY7C68320-56LFXC)
- Clear 3.15 V to 3.45 V operating range (بەراورد بەCY7C68320-56LFXC)
تێبینییەکانی دیزاین
Use the manufacturer land pattern for the 56-QFN, 8 mm by 8 mm package and follow the exposed-pad instructions exactly. Keep USB traces short, provide a continuous ground reference, and place decoupling capacitors near their associated power pins. The 56-terminal footprint leaves little room for improvised fanout, so validate the escape-routing geometry and solder mask before releasing artwork.
Design the bridge supply around the documented 3.15 V to 3.45 V operating range, including tolerance from the upstream regulator. Confirm the exact core, I/O, and auxiliary rail requirements from the manufacturer pin and power tables before assigning voltages. Coordinate ATA drive power-up with host-controlled sequencing so the interface is not exposed to an incompatible startup condition.
Route USB differential pairs as a controlled impedance pair with continuous reference planes and minimize stubs and test-pad discontinuities. Keep the ATA and USB routing regions logically separated where possible, and use the package reference plane to minimize return-path discontinuity. Signal-integrity conclusions require the actual trace dimensions, dielectric properties, connector geometry, and operating speed from the complete design.
Do not treat a shared 56-QFN body as proof that every EZ-USB AT2LP ordering code is interchangeable. Compare pin names, ATA support, USB behavior, firmware, clock requirements, power sequencing, and exposed-pad treatment between the exact datasheets. Also verify the full temperature grade and lifecycle requirements because related bridge revisions can use similar package dimensions while differing in supported functions.
زانیاری پابەندبوون
The exact material-compliance declarations for this ordering code require confirmation from the current manufacturer product documentation.