DG381ACJ+ - Dual SPST 50 Ohm Analog Switch | Analog Devices
MPN: DG381ACJ+ ✓ چالاکDG381ACJ+ گشتی
An analog switch is a voltage-controlled semiconductor that connects or isolates circuit nodes using low-impedance CMOS transmission gates. The DG381 belongs to the analog switch and multiplexer hierarchy within interface ICs and power-management-adjacent signal-path components. Its two independent single-pole, single-throw channels allow a source signal to be routed to one destination at a time, making the device useful when a compact, logic-controlled routing element is required.
The DG381ACJ+ provides a 50-ohm on-state resistance, approximately 6 pF of switch capacitance, and dual-rail operation extending to ±18 V. These characteristics are important for systems that switch moderate-amplitude analog signals rather than high-current loads. The 0°C to +70°C rating identifies the device as a commercial-temperature component, so applications requiring extended industrial or automotive temperature coverage need separate qualification.
Internally, the device uses CMOS circuitry to control the analog channels. A specified on-resistance value alone does not determine signal fidelity; channel matching, capacitance, switching time, leakage, off-state isolation, and crosstalk also affect performance. The published crosstalk rating of -74 dB at 500 kHz indicates isolation between channels at that test frequency. Designers should account for these dynamic characteristics when routing fast edges, low-level signals, or sources connected through long PCB traces.
Typical uses include sensor selection, sample-and-hold paths, measurement-signal routing, dual-channel test interfaces, and control systems that need two independently controlled analog paths. The device can also serve as a compact isolation element between a source and destination stage when the controlled signal lies within its supply-voltage range. A dual supply permits bipolar signal handling, while single-ended operation may also be possible depending on the circuit configuration described in the manufacturer datasheet.
For PCB implementation, preserve short analog traces and place input and output decoupling close to the device. Treat the control pins as digital signals that should not be allowed to overshoot the supply rails. Check absolute maximum voltage and current limits before switching unusual waveforms, and account for injected charge and off-state leakage when the switched source has a high impedance.
This product page combines the DG381ACJ+ electrical characteristics, package and supply limits with verified drop-in references and practical circuit guidance. It is intended to help engineers identify whether the dual SPST topology, switching speed, resistance, and commercial temperature rating match a specific analog-routing design.
جێگرەوەکانی جێگۆڕکێ بۆ DG381ACJ+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DG381ACJ+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
DG381ACJ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DG300ACJ+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DG381ACJ-
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DG381ACJ+ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Circuits | 2 circuits |
| Switch Configuration | 1:1 SPST |
| Number of Channels | 2 channels |
| On-State Resistance | 50 ohm |
| Positive Supply Voltage Range | +5 V to +18 V |
| Negative Supply Voltage Range | -18 V to -5 V |
| Dual Supply Operating Voltage | ±5 V to ±18 V |
| Turn-On Time | 300 ns |
| Turn-Off Time | 250 ns |
| Switch Capacitance | 6 pF |
| Crosstalk | -74 dB at 500 kHz |
| مەودای پلەی گەرمیی کارکردن | 0°C to +70°C |
| پاکێج | 14-pin PDIP, 0.300-inch body |
| جۆری دامەزراندن | Through-hole |
| Process Technology | CMOS |
| دۆخی RoHS | Compliant |
ڕێنمایی ڕێکخستنی پینی DG381ACJ+ 14-pin pdip, 0.300-inch body
ڕێکخستنی پین بۆ DG381ACJ+ (پاکێجی 14-pin pdip, 0.300-inch body). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DG381ACJ+.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DG381ACJ+ گونجاوە بۆ 6 بەکارھێنانs: Dual-Channel Sensor Signal Routing, Precision Test and Measurement Interfaces, Sample-and-Hold Signal Paths, Communication Equipment Signal Isolation, Data Acquisition Multiplexer Front Ends, Audio and Low-Level Analog Routing.
Dual-Channel Sensor Signal Routing
The DG381ACJ+ can route two sensor or conditioning outputs through separate 1:1 SPST channels when a system must select one source at a time. Its 50-ohm on resistance is appropriate for moderate-impedance sensor paths, while approximately 6 pF of switch capacitance helps define the settling behavior at the destination. The device operates from ±5 V to ±18 V, allowing bipolar sensor signals when the circuit uses both supply rails. Use short PCB traces and account for the 250 ns turn-off and 300 ns turn-on intervals when the selected channel must settle before measurement.
پێشنیارکراو
Precision Test and Measurement Interfaces
The DG381ACJ+ is suitable for test-interface boards that must connect one instrument channel to one of several circuit nodes. Two independently controlled SPST paths provide compact routing, and the 50-ohm on resistance introduces a defined series impedance that must be included in high-impedance measurement calculations. The specified 250 ns to 300 ns switching times support moderate-speed systems, while the -74 dB crosstalk figure at 500 kHz helps characterize isolation between channels. Place the device near the routed nodes and keep control traces away from sensitive analog inputs to minimize switching coupling.
پێشنیارکراو
Sample-and-Hold Signal Paths
The DG381ACJ+ can isolate a sampling node from its source or connect a buffered signal to a downstream hold stage. Its approximately 6 pF switch capacitance contributes to the charge-transfer and settling behavior, while the 50-ohm on resistance should be included when calculating settling time with the sampling capacitor and input impedance. Dual ±5 V to ±18 V operation permits bipolar signals when required by the acquisition circuit. Designers should compare the 250 ns turn-off and 300 ns turn-on timing with the required acquisition interval and ensure the connected amplifier can tolerate the control-pin switching transient.
پێشنیارکراو
Communication Equipment Signal Isolation
The DG381ACJ+ may be used to isolate or cross-connect moderate-bandwidth analog lines in communication equipment. Its -74 dB crosstalk rating at 500 kHz provides a defined isolation benchmark, and the 50-ohm on resistance is compatible with many line-level interfaces when impedance matching is appropriate. The approximately 250 ns turn-off and 300 ns turn-on times make it practical for slower analog paths rather than high-rate serial routing. Keep return paths short, maintain continuous ground references, and verify that signal amplitude and supply polarity remain within the absolute maximum ratings.
پێشنیارکراو
Data Acquisition Multiplexer Front Ends
The two independent SPST channels of the DG381ACJ+ can be used at the front end of a compact data-acquisition system to select isolated measurement paths. The 50-ohm series resistance and approximately 6 pF capacitance influence source loading and transient settling, so both values should be included in the input-buffer design. The 0°C to +70°C commercial rating is suitable for room-temperature laboratory equipment but may be insufficient for unconditioned industrial enclosures. Use short routed traces, local bypassing, and a control sequence that allows approximately 300 ns or more for turn-on before taking the measurement.
پێشنیارکراو
Audio and Low-Level Analog Routing
The DG381ACJ+ can route two low-level analog paths in audio or instrumentation circuitry when 50-ohm on resistance is acceptable. The device's approximately 6 pF capacitance and 250 ns to 300 ns switching times must be compared with the impedance and bandwidth of the connected source, preventing excessive attenuation or transient distortion in high-impedance nodes. Dual supplies of ±5 V to ±18 V support bipolar signal routing, subject to the manufacturer's signal and absolute maximum limits. Keep the analog traces short, maintain a continuous ground reference, and position the device away from switching power nodes to minimize interference.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DG381ACJ+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DG381ACJ | DG300ACJ+ | DG381ACJ- |
|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
جیاکەرەوە سەرەکییەکان
- Direct 14-pin PDIP drop-in candidate (بەراورد بەDG381ACJ)
- Published complete-replacement cross reference (بەراورد بەDG300ACJ+)
- Commercial dual-supply switching specification (بەراورد بەDG381ACJ-)
تێبینییەکانی دیزاین
Include the 50-ohm on-state resistance and approximately 6 pF switch capacitance in the source-to-load model. For a high-impedance destination, the capacitance increases settling time and can preserve switching transients as voltage steps. Add the input capacitance, routing capacitance, and receiver impedance before estimating an acquisition settling interval. The nominal 250 ns turn-off and 300 ns turn-on times describe device transitions but do not by themselves guarantee that the connected node has reached final accuracy.
Route switched analog signals as short and direct as practical, with a continuous ground reference beneath or adjacent to the signal path. Keep the control traces away from sensitive analog nodes and place supply bypassing close to the device pins. Because this is a through-hole PDIP package, maintain adequate spacing from surrounding heat sources and high-impedance inputs. Follow the manufacturer pin table when assigning traces; do not infer control polarity or common-terminal connections from a generic SPST layout.
Do not treat the ±18 V supply capability as permission to switch arbitrary ±18 V signals. Verify the separate signal-voltage, control-logic, absolute maximum, and current limits in the manufacturer datasheet. Avoid exceeding the 0°C to +70°C commercial-temperature range, and check the effects of power-up states if the control lines can float. Also verify injected charge and off-state leakage when switching sources with high source impedance or storing small signals.
زانیاری پابەندبوون
RoHS compliance is identified for DG381ACJ+. The component is specified as a commercial-temperature part, and no separate automotive qualification is indicated.