Analog Devices

DG381ACJ+ - Dual SPST 50 Ohm Analog Switch | Analog Devices

부품 번호: DG381ACJ+ ✓ 활성
+5 V to +18 V Vdss 50 ohm Rds(on) 14-pin PDIP, 0.300-inch body Package
MOQ: 1 |

DG381ACJ+ 개요

The Analog Devices DG381ACJ+ is a dual-circuit CMOS analog switch with two 1:1 SPST channels, a typical on-state resistance of 50 ohms, and a 14-pin PDIP package. It supports dual supply voltages from ±5 V to ±18 V, operates across the 0°C to +70°C commercial temperature range, and provides approximately 250 ns turn-off and 300 ns turn-on switching times. The device is intended for general-purpose signal routing in analog, instrumentation, communication, and test systems.

An analog switch is a voltage-controlled semiconductor that connects or isolates circuit nodes using low-impedance CMOS transmission gates. The DG381 belongs to the analog switch and multiplexer hierarchy within interface ICs and power-management-adjacent signal-path components. Its two independent single-pole, single-throw channels allow a source signal to be routed to one destination at a time, making the device useful when a compact, logic-controlled routing element is required.

The DG381ACJ+ provides a 50-ohm on-state resistance, approximately 6 pF of switch capacitance, and dual-rail operation extending to ±18 V. These characteristics are important for systems that switch moderate-amplitude analog signals rather than high-current loads. The 0°C to +70°C rating identifies the device as a commercial-temperature component, so applications requiring extended industrial or automotive temperature coverage need separate qualification.

Internally, the device uses CMOS circuitry to control the analog channels. A specified on-resistance value alone does not determine signal fidelity; channel matching, capacitance, switching time, leakage, off-state isolation, and crosstalk also affect performance. The published crosstalk rating of -74 dB at 500 kHz indicates isolation between channels at that test frequency. Designers should account for these dynamic characteristics when routing fast edges, low-level signals, or sources connected through long PCB traces.

Typical uses include sensor selection, sample-and-hold paths, measurement-signal routing, dual-channel test interfaces, and control systems that need two independently controlled analog paths. The device can also serve as a compact isolation element between a source and destination stage when the controlled signal lies within its supply-voltage range. A dual supply permits bipolar signal handling, while single-ended operation may also be possible depending on the circuit configuration described in the manufacturer datasheet.

For PCB implementation, preserve short analog traces and place input and output decoupling close to the device. Treat the control pins as digital signals that should not be allowed to overshoot the supply rails. Check absolute maximum voltage and current limits before switching unusual waveforms, and account for injected charge and off-state leakage when the switched source has a high impedance.

This product page combines the DG381ACJ+ electrical characteristics, package and supply limits with verified drop-in references and practical circuit guidance. It is intended to help engineers identify whether the dual SPST topology, switching speed, resistance, and commercial temperature rating match a specific analog-routing design.

드롭인 대체품: DG381ACJ+ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: DG381ACJ+ (동일 폼 팩터 및 풋프린트) — 차이점: Package.

Analog Devices
Package: DIP-14
비교 대상: DG381ACJ+ →

DG381ACJ

✅ 드롭인
📦 14-pin PDIP
Same 14-pin PDIP footprint and 2-circuit 1:1 SPST function with 50-ohm on resistance; the published comparison reports no functional or terminal difference.

📋 참조 대체품 (카탈로그에 없음)

DG300ACJ+

✅ 드롭인
Maxim Integrated
📦 14-pin PDIP
2 · 1:1 · 50 ohm · SPST · CMOS · TTL and CMOS compatible · ±5V to ±18V · 14-pin PDIP, 0.3 inch

가격 문의

데이터시트 보기 →

DG381ACJ-

✅ 드롭인
📦 14-pin PDIP
Same 14-pin PDIP package and dual ±5 V to ±18 V supply range with approximately 250 ns turn-off and 300 ns turn-on timing; ordering-code details require confirmation.

📋 참조 대체품 (카탈로그에 없음)

DG381ACJ+ 최대 정격 & 전기적 특성

Number of Circuits 2 circuits
Switch Configuration 1:1 SPST
Number of Channels 2 channels
On-State Resistance 50 ohm
Positive Supply Voltage Range +5 V to +18 V
Negative Supply Voltage Range -18 V to -5 V
Dual Supply Operating Voltage ±5 V to ±18 V
Turn-On Time 300 ns
Turn-Off Time 250 ns
Switch Capacitance 6 pF
Crosstalk -74 dB at 500 kHz
동작 온도 범위 0°C to +70°C
패키지 14-pin PDIP, 0.300-inch body
실장 유형 Through-hole
Process Technology CMOS
RoHS 상태 Compliant

DG381ACJ+ 14-pin pdip, 0.300-inch body 핀 구성 가이드

DG381ACJ+(14-pin pdip, 0.300-inch body 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

DG381ACJ+의 14-pin pdip, 0.300-inch body 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: DG381ACJ+.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

DG381ACJ+ 적합 용도: 6 애플리케이션s: Dual-Channel Sensor Signal Routing, Precision Test and Measurement Interfaces, Sample-and-Hold Signal Paths, Communication Equipment Signal Isolation, Data Acquisition Multiplexer Front Ends, Audio and Low-Level Analog Routing.

🧩

Dual-Channel Sensor Signal Routing

The DG381ACJ+ can route two sensor or conditioning outputs through separate 1:1 SPST channels when a system must select one source at a time. Its 50-ohm on resistance is appropriate for moderate-impedance sensor paths, while approximately 6 pF of switch capacitance helps define the settling behavior at the destination. The device operates from ±5 V to ±18 V, allowing bipolar sensor signals when the circuit uses both supply rails. Use short PCB traces and account for the 250 ns turn-off and 300 ns turn-on intervals when the selected channel must settle before measurement.

🔧

Precision Test and Measurement Interfaces

The DG381ACJ+ is suitable for test-interface boards that must connect one instrument channel to one of several circuit nodes. Two independently controlled SPST paths provide compact routing, and the 50-ohm on resistance introduces a defined series impedance that must be included in high-impedance measurement calculations. The specified 250 ns to 300 ns switching times support moderate-speed systems, while the -74 dB crosstalk figure at 500 kHz helps characterize isolation between channels. Place the device near the routed nodes and keep control traces away from sensitive analog inputs to minimize switching coupling.

⚡

Sample-and-Hold Signal Paths

The DG381ACJ+ can isolate a sampling node from its source or connect a buffered signal to a downstream hold stage. Its approximately 6 pF switch capacitance contributes to the charge-transfer and settling behavior, while the 50-ohm on resistance should be included when calculating settling time with the sampling capacitor and input impedance. Dual ±5 V to ±18 V operation permits bipolar signals when required by the acquisition circuit. Designers should compare the 250 ns turn-off and 300 ns turn-on timing with the required acquisition interval and ensure the connected amplifier can tolerate the control-pin switching transient.

🌐

Communication Equipment Signal Isolation

The DG381ACJ+ may be used to isolate or cross-connect moderate-bandwidth analog lines in communication equipment. Its -74 dB crosstalk rating at 500 kHz provides a defined isolation benchmark, and the 50-ohm on resistance is compatible with many line-level interfaces when impedance matching is appropriate. The approximately 250 ns turn-off and 300 ns turn-on times make it practical for slower analog paths rather than high-rate serial routing. Keep return paths short, maintain continuous ground references, and verify that signal amplitude and supply polarity remain within the absolute maximum ratings.

🖥️

Data Acquisition Multiplexer Front Ends

The two independent SPST channels of the DG381ACJ+ can be used at the front end of a compact data-acquisition system to select isolated measurement paths. The 50-ohm series resistance and approximately 6 pF capacitance influence source loading and transient settling, so both values should be included in the input-buffer design. The 0°C to +70°C commercial rating is suitable for room-temperature laboratory equipment but may be insufficient for unconditioned industrial enclosures. Use short routed traces, local bypassing, and a control sequence that allows approximately 300 ns or more for turn-on before taking the measurement.

🎧

Audio and Low-Level Analog Routing

The DG381ACJ+ can route two low-level analog paths in audio or instrumentation circuitry when 50-ohm on resistance is acceptable. The device's approximately 6 pF capacitance and 250 ns to 300 ns switching times must be compared with the impedance and bandwidth of the connected source, preventing excessive attenuation or transient distortion in high-impedance nodes. Dual supplies of ±5 V to ±18 V support bipolar signal routing, subject to the manufacturer's signal and absolute maximum limits. Keep the analog traces short, maintain a continuous ground reference, and position the device away from switching power nodes to minimize interference.

추천 제품 요약

DG381ACJ Same-footprint dual SPST routing alternative 사용처: Dual-Channel Sensor Signal Routing, Precision Test and Measurement Interfaces, Sample-and-Hold Signal Paths, Communication Equipment Signal Isolation, Data Acquisition Multiplexer Front Ends, Audio and Low-Level Analog Routing DG300ACJ+ 14-pin analog-switch cross reference 사용처: Dual-Channel Sensor Signal Routing, Sample-and-Hold Signal Paths, Communication Equipment Signal Isolation, Audio and Low-Level Analog Routing DG381ACJ- Equivalent 14-pin PDIP variant 사용처: Precision Test and Measurement Interfaces, Data Acquisition Multiplexer Front Ends
What is the DG381ACJ+ and what are its main specifications?
The DG381ACJ+ is a dual-circuit CMOS analog switch with two 1:1 SPST channels, 50-ohm on-state resistance, and a 14-pin PDIP package. According to the Analog Devices datasheet, it supports dual supply voltages of ±5 V to ±18 V, operates from 0°C to +70°C, and offers approximately 300 ns turn-on and 250 ns turn-off times. Its key application is routing one source to one destination through each of two independently controlled channels.
What is the operating voltage range of DG381ACJ+?
The DG381ACJ+ operates with positive and negative supply voltages from +5 V to +18 V and -18 V to -5 V, respectively. According to the Analog Devices datasheet, this enables bipolar signal routing when both rails are present. Control and analog signals must remain within the applicable absolute maximum and input-voltage limits described by the manufacturer. The component does not use a single 3.3 V or 5 V rail configuration.
Where can I download the DG381ACJ+ datasheet PDF?
The DG381ACJ+ datasheet landing page is available through the Octopart datasheet link listed on this product page. According to the manufacturer datasheet, the document contains the definitive pin descriptions, recommended operating conditions, electrical characteristics, switching timing, and application information. Use the manufacturer document for final PCB pin assignment and limit checks, especially when operating near ±18 V or changing the analog signal frequency.
Where can I find the DG381ACJ+ pinout?
The DG381ACJ+ uses a 14-pin PDIP package with a 0.300-inch body, but a complete numbered pin description is not reproduced on this page. Use the pin-description table in the Analog Devices datasheet before assigning PCB tracks. The package pin count is 14, and the device is an analog switch rather than a standard logic IC. Confirm control, supply, common, normally closed, and normally open connections directly from that table.
Is DG381ACJ+ suitable for bipolar analog signal switching?
Yes, the DG381ACJ+ is suitable for bipolar analog signal switching within its specified supply and signal limits. According to the Analog Devices datasheet, the device supports ±5 V to ±18 V dual supplies, has 50-ohm on-state resistance, and is specified at approximately 250 ns turn-off and 300 ns turn-on. Check input swing, leakage, channel capacitance, and absolute maximum ratings before routing precision or high-amplitude signals.
What can replace the DG381ACJ+ on the same PCB?
DG381ACJ and DG300ACJ+ are identified as direct replacement candidates for the DG381ACJ+, while DG381ACJ- is an equivalent 14-pin PDIP device with the same general dual-supply switching characteristics. The cross-reference information reports consistent terminals, package, and functional characteristics for the direct replacements. Confirm the exact pin labels, absolute maximum ratings, control polarity, and timing limits in the manufacturer datasheet before production substitution.
What is the best drop-in replacement for DG381ACJ+?
DG381ACJ is the closest listed drop-in candidate because it uses the same 14-pin PDIP format and represents the same dual 1:1 SPST function with 50-ohm on-state resistance. The published comparison states that the terminals and packages are consistent and that the replacement requires no circuit modification. DG300ACJ+ and DG381ACJ- are additional cross-reference candidates, but their exact electrical limits should be checked against the selected application.
What is the difference between DG381ACJ+ and DG381ACJ?
The DG381ACJ and DG381ACJ+ are presented as functionally and mechanically compatible versions of the same 14-pin PDIP dual-SPST analog switch. The DG381ACJ+ listing identifies a 50-ohm on-resistance device with ±5 V to ±18 V dual supplies and 250 ns to 300 ns switching times. The published comparison states that terminal and package consistency allows replacement without circuit modification, although ordering-code meaning should be confirmed with the manufacturer.
DG381ACJ+ vs DG300ACJ+ - which is better for a general-purpose analog router?
DG381ACJ+ and DG300ACJ+ are both listed as 14-pin Maxim Integrated analog-switch options, and the cross-reference information describes them as completely replaceable with consistent performance, terminals, and packages. The DG381ACJ+ is specifically characterized as a dual 1:1 SPST device with 50-ohm on resistance. Choose it when that published switch configuration is required, and verify the DG300ACJ+ electrical table if the design depends on leakage, charge injection, or exact channel matching.
When should I choose DG381ACJ+ instead of DG381ACJ?
Choose DG381ACJ+ when its ordering code is the approved component for the design or when you need the explicitly listed + version. The published DG381ACJ comparison describes the two devices as having consistent characteristics, terminals, and packages, so DG381ACJ is the practical drop-in candidate when that exact suffix is approved. For new layouts, preserve the 14-pin PDIP footprint and verify the manufacturer ordering table before fixing the component callout.
Is DG381ACJ+ suitable for industrial equipment?
The DG381ACJ+ may be used only where the ambient and circuit conditions fall inside its 0°C to +70°C commercial-temperature rating. According to the Analog Devices datasheet, that range is a defining operating limitation. A control cabinet or industrial enclosure may exceed 70°C even when the external environment is moderate. For such installations, select a switch explicitly rated for the required temperature range and automotive or industrial qualification.
What is the power consumption of DG381ACJ+?
The DG381ACJ+ supply current is not stated in the accessible product summary, so an exact power-consumption figure cannot be assigned safely. According to the Analog Devices datasheet, the device accepts positive and negative supplies from +5 V to +18 V and -18 V to -5 V. Calculate board-level consumption from the control-state supply currents listed in that document, adding the rail-voltage difference times the relevant quiescent and channel currents.
How does the 50-ohm on resistance affect DG381ACJ+ applications?
The 50-ohm on resistance makes the DG381ACJ+ suitable for moderate-impedance signal paths rather than applications requiring nearly lossless transfer. According to the Analog Devices datasheet, the device also has approximately 6 pF of switch capacitance and switching times of about 250 ns to 300 ns. Together, these values determine attenuation, charging behavior, bandwidth, and edge distortion, so include the source and destination impedances in signal-integrity calculations.
Is DG381ACJ+ RoHS compliant?
Yes, the DG381ACJ+ is identified as RoHS compliant in the manufacturer-related product information. The device is a commercial-temperature, 14-pin PDIP analog switch rated for 0°C to +70°C. RoHS status addresses restricted substance requirements in the product, not automotive qualification or extended-temperature suitability. Request the current manufacturer compliance declaration when a formal procurement or environmental assessment record is required.
Where to buy DG381ACJ+ online and what are its lead time and stock status?
Use the Request a Quote form on this page to ask for DG381ACJ+ availability, current lead time, minimum order quantity, and the exact + ordering code. The manufacturer supports a commercial 0°C to +70°C temperature range, and the component is offered in a 14-pin PDIP package. Stock and delivery timing can vary by quantity, so confirm the orderable suffix and production allocation directly through the quotation workflow before releasing a build.

엔지니어링 참조 데이터: DG381ACJ+ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the DG381ACJ+ when the design requires a dual 1:1 SPST CMOS analog switch in a 14-pin PDIP package and operates within 0°C to +70°C. Its 50-ohm on resistance, approximately 6 pF capacitance, and 250 ns to 300 ns switching times fit moderate-impedance, moderate-speed analog paths. Select DG381ACJ when that exact ordering code is approved and the published cross-reference confirms the same footprint and function. Consider DG300ACJ+ when it is the approved direct replacement for the intended sourcing channel, but verify its leakage and dynamic specifications against the original design. DG381ACJ- is another closely aligned 14-pin option, although the meaning of the ordering suffix should be confirmed with the manufacturer. None of these references should be selected solely from package shape; control polarity, absolute maximum limits, charge injection, and temperature requirements must also match.

대체품과의 비교

파라미터 이 제품 DG381ACJ DG300ACJ+ DG381ACJ-
Package 14-pin PDIP 14-pin PDIP 14-pin PDIP 14-pin PDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices

주요 차별점

  • Direct 14-pin PDIP drop-in candidate (vs DG381ACJ)
  • Published complete-replacement cross reference (vs DG300ACJ+)
  • Commercial dual-supply switching specification (vs DG381ACJ-)

설계 노트

Include the 50-ohm on-state resistance and approximately 6 pF switch capacitance in the source-to-load model. For a high-impedance destination, the capacitance increases settling time and can preserve switching transients as voltage steps. Add the input capacitance, routing capacitance, and receiver impedance before estimating an acquisition settling interval. The nominal 250 ns turn-off and 300 ns turn-on times describe device transitions but do not by themselves guarantee that the connected node has reached final accuracy.

Route switched analog signals as short and direct as practical, with a continuous ground reference beneath or adjacent to the signal path. Keep the control traces away from sensitive analog nodes and place supply bypassing close to the device pins. Because this is a through-hole PDIP package, maintain adequate spacing from surrounding heat sources and high-impedance inputs. Follow the manufacturer pin table when assigning traces; do not infer control polarity or common-terminal connections from a generic SPST layout.

Do not treat the ±18 V supply capability as permission to switch arbitrary ±18 V signals. Verify the separate signal-voltage, control-logic, absolute maximum, and current limits in the manufacturer datasheet. Avoid exceeding the 0°C to +70°C commercial-temperature range, and check the effects of power-up states if the control lines can float. Also verify injected charge and off-state leakage when switching sources with high source impedance or storing small signals.

규정 준수 정보

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

RoHS compliance is identified for DG381ACJ+. The component is specified as a commercial-temperature part, and no separate automotive qualification is indicated.

데이터 검증일: 2026-11-16 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

DG381ACJ+ datasheet DG381ACJ+ pinout DG381ACJ+ datasheet pdf DG381ACJ+ specifications Analog Devices DG381ACJ+ DG381ACJ+ equivalent DG381ACJ+ replacement DG381ACJ+ cross reference DG381ACJ+ vs DG381ACJ DG381ACJ+ PDIP footprint DG381ACJ+ analog switch circuit DG381ACJ+ price DG381ACJ+ stock DG381ACJ+ lead time DG381ACJ 50 ohm SPST switch

관련 부품 & 용어

Analog Devices Maxim Integrated DG381ACJ+ DG381ACJ DG381ACJ- DG300ACJ+ analog switch SPST switch CMOS analog switch interface IC multiplexer 14-pin PDIP DIP-14 through-hole package 50-ohm on resistance 6 pF switch capacitance dual supply voltage ±5 V to ±18 V signal routing test and measurement sensor signal switching RoHS crosstalk turn-on time turn-off time
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기