DG407DN+T Dual 8:1 CMOS Analog Mux | Analog Devices
MPN: DG407DN+T ✓ چالاکDG407DN+T گشتی
An analog multiplexer is an integrated switching circuit that connects one of several analog inputs to a shared output according to digital address logic. The dual 8:1 architecture provides two independent 8:1 multiplexer sections, while the differential configuration can support sixteen single-ended channels or eight differential channels. This places the DG407DN+T within the hierarchy of analog switch IC, multiplexer, interface IC, and semiconductor.
Key characteristics include a maximum on-resistance of 100 ohms, a switch-on time of 200 ns, and an operating temperature range from -40 °C to +85 °C. Its CMOS implementation supports low-power mixed-signal systems, while the separate enable input allows a selected multiplexer section to participate in broader system control. The 28-PLCC package is intended for surface-mount assembly and provides a defined footprint for PCB layouts based on the device pinout.
The DG407 family is described by Analog Devices as an improved alternative to industry-standard DG406 and DG407 devices. Its address decoder accepts digital control signals, selects the requested analog path, and connects that path to the common output. Because switch resistance and transition time influence insertion loss and settling behavior, the 100-ohm resistance and 200 ns turn-on specification are important when designing acquisition chains or instrumentation with limited timing margin.
The manufacturer identifies audio signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment as suitable applications. These uses benefit from centralized analog-channel selection, reduced wiring complexity, and digital control of analog signals. In a data-acquisition system, the DG407DN+T can route multiple sensor or measurement inputs toward a shared converter while address logic selects the active source.
PCB design should follow the package drawing and pin-description table in the Analog Devices datasheet, particularly for supply decoupling and the location of the common terminals. Allow adequate signal settling before sampling after a channel change, and evaluate the 200 ns switching interval together with source impedance, capacitance, and converter acquisition requirements. Guard against input overvoltage, and ensure that control levels meet the device's TTL- or CMOS-compatible logic requirements.
This product record combines manufacturer application guidance, interface characteristics, package information, sourcing terms, and drop-in replacement analysis. It is intended to help engineers determine whether the DG407DN+T architecture, electrical limits, and 28-PLCC footprint fit a multiplexed analog signal-routing design.
جێگرەوەکانی جێگۆڕکێ بۆ DG407DN+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DG407DN+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Maximum On-State Resistance, Multiplexer Configuration, Package.
DG407DN+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DG407DN-T1
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DG407DN-T1-E3
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DG407DN+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADG407BPZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DG407DN+T تایبەتمەندییەکان
| Multiplexer Configuration | Dual 8:1 multiplexer |
| Single-Ended Channel Count | 16 channels |
| Differential Channel Count | 8 channels |
| Maximum On-State Resistance | 100 ohms |
| Switch-On Time | 200 ns |
| Technology | CMOS |
| Logic Compatibility | TTL- and CMOS-compatible |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +85 °C |
| پاکێج | 28-pin PLCC, 11.51 mm × 11.51 mm |
| Number of Circuits | 2 circuits |
| Number of Terminals | 28 terminals |
| جۆری دامەزراندن | Surface mount |
| Enable Function | Device-section enable control |
| Digital Address Inputs | 4-bit address control |
ڕێنمایی ڕێکخستنی پینی DG407DN+T 28-pin plcc, 11.51 mm × 11.51 mm
ڕێکخستنی پین بۆ DG407DN+T (پاکێجی 28-pin plcc, 11.51 mm × 11.51 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DG407DN+T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DG407DN+T گونجاوە بۆ 6 بەکارھێنانs: Data Acquisition Systems, Test and Measurement Equipment, Audio Signal Routing, Communication Systems, Guidance and Control Systems, Sample-and-Hold Circuits.
Data Acquisition Systems
The DG407DN+T fits multiplexed data-acquisition systems that must route multiple analog inputs to a shared converter or measurement channel. Its dual 8:1 organization supports 16 single-ended channels or 8 differential channels, reducing the number of external signal-routing connections. The 100-ohm maximum on-state resistance can be included in the source impedance budget, while the 200 ns switch-on time starts the settling interval. After changing the four-bit address, allow additional time for source capacitance, filters, wiring, and the receiving ADC to acquire the selected signal accurately.
پێشنیارکراو
Test and Measurement Equipment
The DG407DN+T is suited to test equipment that selects among several sensors, references, or injected signals without duplicating analog front-end circuitry. Two independent 8:1 sections can organize the routing architecture, and the address and enable inputs support deterministic control from a test controller. Designers should account for the 100-ohm maximum on-resistance and 200 ns switch-on time when defining measurement settling and timing margins. Accurate acquisition also depends on the selected source impedance, cable or PCB capacitance, protection networks, and the timing of the downstream measuring instrument.
پێشنیارکراو
Audio Signal Routing
The DG407DN+T can route multiple analog audio or control signals in a multi-source system while keeping channel selection under digital control. Analog Devices identifies audio signal routing as a DG407 application. The 100-ohm maximum on-state resistance introduces path loss that should be checked against the source and load impedances, particularly for low-amplitude signals. The 200 ns switch-on specification describes the device transition rather than complete signal settling, so the system must also account for capacitances, filtering, and the time required before the destination stage captures the selected waveform.
پێشنیارکراو
Communication Systems
The DG407DN+T is appropriate for communication equipment that selects among several analog channels, monitoring points, or interface signals. Its dual 8:1 structure permits compact routing of a larger number of single-ended or differential sources, while TTL- and CMOS-compatible address and enable control supports integration with digital logic. Signal-integrity planning should include the 100-ohm maximum switch resistance and the 200 ns turn-on interval. Route high-impedance or high-speed nodes carefully, keep return paths continuous, and verify settling at the bandwidth of the communication channel.
پێشنیارکراو
Guidance and Control Systems
The DG407DN+T can centralize analog command, feedback, or sensor selection in guidance and control equipment. The device's -40 °C to +85 °C industrial temperature range supports use across varied operating environments, and the two 8:1 sections provide a practical structure for organizing related signal groups. Engineers should verify that every analog input remains within the device's permitted signal range and that control levels satisfy the TTL- or CMOS-compatible logic requirements. Timing design should allow the 200 ns switching transition plus external settling before the control loop consumes a newly selected feedback signal.
پێشنیارکراو
Sample-and-Hold Circuits
The DG407DN+T can select the signal presented to a sample-and-hold stage in instrumentation requiring multiple analog sources. The dual 8:1 architecture permits a compact implementation with 16 single-ended or 8 differential selections, while digital address and enable control coordinates the transition. The 100-ohm maximum on-state resistance must be combined with the source impedance when calculating settling and acquisition behavior. The 200 ns switch-on time is only one portion of the recovery period; capacitor charging, switch capacitance, hold droop, and the sampling amplifier's input network also determine whether the captured value meets the system accuracy target.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DG407DN+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DG407DN | DG407DN-T1 | DG407DN-T1-E3 | DG407DN+ | ADG407BPZ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-PLCC (11.51 x 11.51 mm) | 28-PLCC (11.51 x 11.51 mm) | 28-PLCC | 28-PLCC | 28-PLCC (J-Lead) | 28-LCC |
| Multiplexer Configuration | Dual 8:1 | Dual 8:1 | Dual 8:1 | Dual 8:1 | Dual 8:1 | Dual 8:1 |
| Single-Ended Channels | 16 channels | 16 channels | 16 channels | 16 channels | 16 channels | 16 channels |
| Differential Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
جیاکەرەوە سەرەکییەکان
- Documented 100-ohm maximum on-state resistance (بەراورد بەADG407BPZ)
- Confirmed 200 ns switch-on interval (بەراورد بەADG407BPZ)
- Specified industrial temperature operation (بەراورد بەADG407BPZ)
تێبینییەکانی دیزاین
Treat the 200 ns switch-on time as the beginning of the settling process rather than the complete acquisition time. The selected path also includes up to 100 ohms of on-resistance, source impedance, PCB and cable capacitance, protection-network capacitance, and downstream filter delay. In measurement systems, begin a new conversion only after a timing interval that covers the switch transition and the RC settling of the selected channel. This prevents samples from adjacent channels or transient switch charge from contaminating the result.
Use the Analog Devices package drawing and pin-description table when placing the 28-PLCC device, analog commons, address inputs, enable inputs, and supply connections. Keep analog traces short where source impedance is high, maintain a continuous ground reference beneath signal paths, and route digital address and enable lines away from sensitive analog inputs. Place any required bypass capacitors near their associated supply pins with short ground returns, following the capacitance and ESR guidance stated in the manufacturer datasheet.
Do not assume that two multiplexers with the same 8:1 description are interchangeable. Before replacing DG407DN+T with DG407DN, DG407DN-T1, DG407DN-T1-E3, DG407DN+, or ADG407BPZ, compare every pin name, address-decoder truth table, enable polarity, supply range, input range, leakage, off-state capacitance, on-resistance, and switching timing. The shared 28-LCC package establishes a footprint match, but only a complete electrical comparison establishes functional drop-in equivalence.
زانیاری پابەندبوون
The DG407 family is listed as a production product by Analog Devices. Specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification statements were not confirmed for the exact DG407DN+T ordering code.