Texas Instruments

DP83848JSQ/NOPB - 10/100 Ethernet PHY Transceiver, 40-WQFN | Texas Instruments

MPN: DP83848JSQ/NOPB ✓ چالاک
3 V to 3.6 V (3.3 V nominal) Vdss 92 mA typical Id 40-pin WQFN (6 x 6 mm) with exposed pad Package
MOQ: 1 |

DP83848JSQ/NOPB گشتی

The Texas Instruments DP83848JSQ/NOPB is a single-port 10/100 Mb/s Ethernet PHY transceiver (PHYTER Mini LS) in a 40-pin WQFN package measuring 6 x 6 mm with an exposed thermal pad. It operates from a single 3.3 V supply with a 3 V to 3.6 V range, supports MII and RMII host interfaces, and draws 92 mA of supply current.

An Ethernet PHY is the physical-layer transceiver inside a network interface: it converts digital parallel data from a host MAC into differential copper signaling on an RJ45 magnetics module, and converts incoming line signals back into digital data. In the product hierarchy it sits as an Ethernet transceiver, then a network interface IC, then an interface IC within the broader semiconductor family. The DP83848 family is built on a low-power 3.3 V, 0.18 um process, which is why it suits space-sensitive embedded systems where board area and standby power are constrained.

Key features of this device include support for both 10BASE-T and 100BASE-TX over Category 5 cable, Auto-MDIX for automatic crossover handling, and performance beyond the 137 m Cat-V reach required by IEEE 802.3. The commercial-temperature grade covers 0 C to +70 C, and the part is offered in a RoHS-compliant, lead-free 40-WQFN package. At 92 mA typical supply current and 264 mW of stated power dissipation, it adds little thermal load to a compact embedded board.

Technically the DP83848J integrates a 10/100 MAC-compatible PHY front end, an MII/RMII-compliant management interface, and PHY strapping and reset pins for hardware-controlled configuration. That means a small microcontroller or FPGA can bring up Ethernet with almost no host-side software, using resistor straps on the configuration pins rather than a driver stack, which matters in industrial control, test equipment, and building-automation nodes.

Typical applications include industrial control boards, HMI panels, set-top and access equipment, printers, IP cameras, and any embedded system that needs a robust copper Ethernet port. For new designs where a smaller footprint or lower system power is the priority, the DP83867 family offers a more integrated alternative, while the DP83848 remains the reference choice for cost-sensitive 10/100 designs.

One key design consideration: the device requires an external 1:1 isolation transformer or integrated magnetics with a center-tap bias network, and the layout must keep the 50-ohm differential pairs away from noisy digital return paths. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and keep the exposed pad tied to a solid ground plane for heat spreading.

This page synthesizes distributor availability, pin-compatible drop-in alternatives, parameter-level comparison tables, and practical layout guidance that go beyond the manufacturer datasheet, so engineers can qualify a 10/100 Ethernet front end quickly.

جێگرەوەکانی جێگۆڕکێ بۆ DP83848JSQ/NOPB — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83848JSQ/NOPB (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Auto-MDIX, Package, RoHS Status, Number of Ports, Cable Reach.

Texas Instruments
Auto-MDIX: Yes
Package: WQFN-40 (6x6 mm)
RoHS Status: Compliant
Texas Instruments
Texas Instruments
Auto-MDIX: Supported
Package: 40-pin WQFN with exposed pad
RoHS Status: unknown

DP83848KSQ/NOPB

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 40-WQFN (6x6)
Ethernet PHY Transceiver · 10/100 Mbps · 3.0 V to 3.6 V · -40C to +85C · MII / RMII · 1 · WQFN-40 (6x6 mm) · Surface Mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

DP83848TSQ/NOPB

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 40-WQFN (6x6)
Single-port Ethernet physical-layer transceiver · 10 Mbps and 100 Mbps · 1 port · 3.3 V · 40-pin WQFN with exposed pad · 6 mm x 6 mm · Surface mount · Supported

پەیوەندی بۆ نرخ

بینینی داتاشیت →

DP83848CSQ/NOPB

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 40-WQFN (6x6)
same 40-WQFN (6x6) pinout and 10/100 Mb/s media support; temperature/qualification suffix differs, current/interface ratings unchanged

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

DP83848IRPAP

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 40-WQFN (6x6)
same 40-WQFN (6x6) footprint and MII/RMII interface, industrial temperature grade instead of 0 C to +70 C commercial; tray packing

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

DP83848IRPAT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 40-WQFN (6x6)
same 40-WQFN (6x6) footprint and MII/RMII interface, industrial temperature grade; tape-and-reel packing instead of tray

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

DP83848JSQ/NOPB تایبەتمەندییەکان

Device Type 10/100 Mb/s Ethernet PHY transceiver (PHYTER Mini LS), single port
خێرایی داتا 10 Mbps and 100 Mbps (100BASE-TX / 10BASE-T)
Host Interface MII and RMII
Supply Voltage Range 3 V to 3.6 V (3.3 V nominal)
ئێستای دابینکردن 92 mA typical
Power Dissipation 264 mW
مەودای پلەی گەرمیی کارکردن 0 C to +70 C (commercial grade)
پاکێج 40-pin WQFN (6 x 6 mm) with exposed pad
ژمارەی پینەکان 40
Process Technology 0.18 um CMOS, low-power 3.3 V
Auto-MDIX Yes, automatic crossover for copper cabling
Cable Reach Beyond 137 m Cat-V cable
جۆری دامەزراندن Surface mount
دۆخی RoHS RoHS compliant
Number of Ports 1
Temperature Grade Commercial (0 C to +70 C)
Termination Standard 1:1 isolation transformer or integrated magnetics
Transceiver Configuration Method Hardware strap pins and reset control
Media Interface Type 10BASE-T, 100BASE-TX
Product Line PHYTER

ڕێنمایی ڕێکخستنی پینی DP83848JSQ/NOPB 40-pin wqfn (6 x 6 mm) with exposed pad

ڕێکخستنی پین بۆ DP83848JSQ/NOPB (پاکێجی 40-pin wqfn (6 x 6 mm) with exposed pad). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 40-pin wqfn (6 x 6 mm) with exposed pad بۆ DP83848JSQ/NOPB

هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83848JSQ/NOPB.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

DP83848JSQ/NOPB گونجاوە بۆ 6 بەکارھێنانs: Industrial Control and Automation Terminals, Printers, Scanners and Office Peripherals, Building Automation and HVAC Gateways, IP Cameras and Video Access Units, Test and Measurement Instruments, Embedded Linux and RTOS Single-Board Computers.

🏭

Industrial Control and Automation Terminals

The DP83848JSQ/NOPB fits industrial control terminals and remote I/O nodes that need a single 10/100 Mb/s copper Ethernet port without the cost of a Gigabit PHY. Its MII and RMII host interfaces let a small microcontroller or FPGA drive the PHY directly, while hardware strap pins and a reset line allow deterministic boot without a full network driver stack. At 3 V to 3.6 V with 92 mA typical supply current and 264 mW dissipation, the 6 x 6 mm WQFN leaves board area for the isolation transformer and termination network. The 0 C to +70 C commercial grade suits enclosure-controlled cabinets rather than unheated outdoor cabinets.

🖨️

Printers, Scanners and Office Peripherals

Printers and multifunction office peripherals typically need one embedded 10/100 port for service printing and network management, which is exactly what the DP83848JSQ/NOPB provides. Its Auto-MDIX function removes crossover-cable confusion at installation sites, and performance beyond the 137 m Cat-V reach gives margin on office cable runs that exceed the formal limit. Because the device supports both MII and RMII, a low-cost Cortex-M can use the simpler RMII timing while an FPGA-based print engine board can use MII. The small 40-WQFN footprint and 264 mW dissipation are valuable in space-constrained desktop chassis.

🏠

Building Automation and HVAC Gateways

Building automation gateways and HVAC controllers frequently add wired Ethernet for BACnet/IP or Modbus-TCP connectivity to existing panel electronics. The DP83848JSQ/NOPB gives those platforms a compact, low-power 10/100 port that fits between the MCU and the panel magnetics without adding a large heatsink area. The 3.3 V single-rail supply aligns with typical controller rails, and 92 mA typical current is easy to include in a panel power budget. Since controllers are frequently deployed in warm enclosed cabinets, check that the commercial 0 C to +70 C grade covers your worst-case ambient or move to an extended-temperature variant.

📹

IP Cameras and Video Access Units

IP camera and video access units need a reliable 10/100 Mb/s link for control traffic, firmware updates, and streaming to a nearby recorder, and the DP83848JSQ/NOPB provides it in a compact footprint. The MII interface supports the parallel data path used by many SoC-based camera engines, while the copper reach beyond 137 m of Cat-V helps in retrofit installations where in-wall cable runs are longer than the specification minimum. Auto-MDIX simplifies installation with mixed switch and PC cabling. The 264 mW dissipation keeps internal enclosure temperatures low, which matters in sealed outdoor camera housings with limited convective cooling.

🖥️

Test and Measurement Instruments

Bench instruments and portable analyzers need a network port for remote control, data export, and firmware maintenance, and the DP83848JSQ/NOPB delivers that in a small 6 x 6 mm WQFN that preserves front-panel layout space. Instruments are usually 24 V powered with a 3.3 V internal rail, so the 3 V to 3.6 V operating range fits naturally, and the 92 mA typical current is negligible against the instrument's own power budget. For remote lab use where the instrument sits more than 100 m from the switch, the extended reach beyond 137 m of Cat-V adds useful margin over the baseline specification.

🧩

Embedded Linux and RTOS Single-Board Computers

Single-board computers running Linux or an RTOS usually expose an MII or RMII port from the SoC, and the DP83848JSQ/NOPB is a straightforward way to add a compliant copper Ethernet interface to that bus. Because the PHY is configured through hardware strap pins and a reset signal, the network interface comes up deterministically at boot without an additional PHY driver being required in the boot path. The 92 mA typical supply current and 264 mW dissipation are easy to accommodate on a 3.3 V rail that already feeds the processor, and the RoHS-compliant lead-free package simplifies regulatory documentation for consumer and education products.

کورتەی بەرهەمە پێشنیارکراوەکان

STM32F103C8T6 STMicroelectronics بەکارهێنراوە لە: Industrial Control and Automation Terminals, Industrial Control and Automation Terminals KSZ8041RNL Microchip Technology بەکارهێنراوە لە: Industrial Control and Automation Terminals, Printers, Scanners and Office Peripherals, Embedded Linux and RTOS Single-Board Computers TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Industrial Control and Automation Terminals LAN9353T/ML Microchip Technology بەکارهێنراوە لە: Printers, Scanners and Office Peripherals SP232EET-L/TR MaxLinear بەکارهێنراوە لە: Printers, Scanners and Office Peripherals STM32F103RCT6 STMicroelectronics بەکارهێنراوە لە: Building Automation and HVAC Gateways KSZ8721SLI Microchip Technology بەکارهێنراوە لە: Building Automation and HVAC Gateways ADM485JNZ Analog Devices بەکارهێنراوە لە: Building Automation and HVAC Gateways DP83867IRRGZR Texas Instruments بەکارهێنراوە لە: IP Cameras and Video Access Units, Embedded Linux and RTOS Single-Board Computers STM32F429ZIT6 STMicroelectronics بەکارهێنراوە لە: IP Cameras and Video Access Units KSZ9897RTXI Microchip Technology بەکارهێنراوە لە: IP Cameras and Video Access Units, Test and Measurement Instruments DP83822HRHBT Texas Instruments بەکارهێنراوە لە: Test and Measurement Instruments MAX3232IPW Texas Instruments بەکارهێنراوە لە: Test and Measurement Instruments STM32F746ZGT6G STMicroelectronics بەکارهێنراوە لە: Embedded Linux and RTOS Single-Board Computers
What is the DP83848JSQ/NOPB used for?
The DP83848JSQ/NOPB is a single-port 10/100 Mb/s Ethernet physical-layer transceiver from Texas Instruments. It converts data between a host MII or RMII interface and twisted-pair copper cabling on the 10BASE-T and 100BASE-TX media, so any embedded board with an RJ45 port needs one. According to the TI DP83848J product page, the PHYTER family targets space-sensitive embedded systems and operates from a single 3.3 V supply while drawing 92 mA typical supply current.
What is the supply voltage range of the DP83848JSQ/NOPB?
The DP83848JSQ/NOPB operates from a 3 V to 3.6 V supply, nominally 3.3 V. The device is built on a low-power 3.3 V, 0.18 um process, and its stated power dissipation is 264 mW with 92 mA typical supply current. Keep the decoupling close to the supply pins and run the 1.2 V internal core rail out only as directed by the pin-description table in the manufacturer datasheet.
What is the operating temperature range of the DP83848JSQ/NOPB?
The DP83848JSQ/NOPB is a commercial-temperature part rated from 0 C to +70 C. If your design must work across a wider industrial or automotive range, choose a DP83848 variant rated for extended temperature or move to the DP83867 family, which offers industrial and automotive grade options. Verify the exact rating of any substitute against the manufacturer product page before committing to a layout.
What package does the DP83848JSQ/NOPB use?
The DP83848JSQ/NOPB is supplied in a 40-pin WQFN package measuring 6 x 6 mm with an exposed thermal pad. The exposed pad must be soldered to a solid ground plane for both electrical return and heat spreading, and the 40-pin footprint is shared across the DP83848 family variants such as the DP83848KSQ/NOPB and DP83848TSQ/NOPB. Use the package drawing in the manufacturer datasheet for land-pattern dimensions.
Where can I download the DP83848JSQ/NOPB datasheet PDF?
The authoritative documentation for the DP83848JSQ/NOPB is the Texas Instruments DP83848J product page and its associated data sheet, which covers the full ordering information, the 40-pin pin description table, the MII/RMII timing diagrams, and the typical application circuit with the isolation transformer. The data sheet also lists the DP83848 family ordering options used for the commercial, extended, and industrial temperature grades.
Where can I find the DP83848JSQ/NOPB pinout?
The 40-pin pin description table in the manufacturer data sheet is the definitive source for pin assignments, including the MII/RMII data pins, clock, chip select, reset, and strap pins. Because the pin names are not reproduced in the product listing, use the datasheet pin-description table when assigning PCB tracks, and note that several pins are configuration straps sampled at reset, so their logic level at power-up must be planned deliberately.
What is the difference between DP83848JSQ/NOPB and DP83848KSQ/NOPB?
The DP83848JSQ/NOPB and DP83848KSQ/NOPB are both 40-pin WQFN (6 x 6 mm) 10/100 Mb/s Ethernet PHYs from Texas Instruments with MII and RMII host interfaces and a 3 V to 3.6 V supply, so they are mechanically and electrically drop-in compatible. The suffix codes denote different grade or qualification options, so check the ordering table in the manufacturer data sheet for the exact temperature range and qualification of each suffix before substituting one for the other.
Is the DP83848JSQ/NOPB the same as the DP83848TSQ/NOPB?
The DP83848TSQ/NOPB shares the same 40-pin WQFN (6 x 6 mm) footprint, the same 10BASE-T and 100BASE-TX media support, and the same MII/RMII host interface as the DP83848JSQ/NOPB, which makes it a mechanical drop-in option on the same board layout. The differences lie in the ordering suffix, so confirm the temperature grade and qualification of the specific suffix against the manufacturer ordering table before making a substitution.
When should I choose the DP83848JSQ/NOPB over a DP83867?
Choose the DP83848JSQ/NOPB when your design only needs a cost-effective 10/100 Mb/s copper Ethernet port in a commercial-temperature environment, because it delivers MII and RMII host interfaces at 3.3 V in a compact 6 x 6 mm WQFN. Choose a DP83867-family device when you need Gigabit rates, integrated RGMII/SGMII options, or industrial and automotive temperature grades, which the DP83848J does not offer.
Is the DP83848JSQ/NOPB suitable for industrial control boards?
The DP83848JSQ/NOPB suits commercial-temperature embedded Ethernet nodes such as controllers, HMIs, printers, and access equipment that operate between 0 C and +70 C. Its MII and RMII interfaces let a small microcontroller or FPGA drive the PHY with minimal host software, and hardware strap pins plus reset allow deterministic boot without a network driver. For wider temperature extremes or ruggedized environments, specify an extended-temperature DP83848 variant instead.
What is the best drop-in replacement for the DP83848JSQ/NOPB?
The closest drop-in replacements are the other 40-pin WQFN (6 x 6 mm) members of the DP83848 family, such as the DP83848KSQ/NOPB and DP83848TSQ/NOPB, because they share the same package, the same 3 V to 3.6 V supply, and the same MII/RMII host interface, so no board change is required. Cross-manufacturer PHYs with a comparable footprint generally differ in pinout or host interface, so validate the pin description table from the manufacturer datasheet before any substitution.
What are the key specifications of the DP83848JSQ/NOPB that engineers should know?
The DP83848JSQ/NOPB is a single-port 10/100 Mb/s Ethernet PHY transceiver in a 40-pin WQFN (6 x 6 mm) package, operating from 3 V to 3.6 V with 92 mA typical supply current and 264 mW power dissipation. It supports 10BASE-T and 100BASE-TX media, offers MII and RMII host interfaces, provides Auto-MDIX automatic crossover, and reaches beyond 137 m of Cat-V cable. The commercial temperature grade covers 0 C to +70 C.
How much power does the DP83848JSQ/NOPB consume in a design?
Estimated: with a 3.3 V rail at the stated 92 mA typical supply current, the DP83848JSQ/NOPB consumes roughly 0.30 W of input power, which matches the 264 mW figure published for the device once internal converter losses are considered. In a compact embedded unit this is a minor thermal contributor, but it must still be included in the 3.3 V rail budget alongside the host processor and any magnetics bias current.
Where can I buy the DP83848JSQ/NOPB and what is the lead time?
The DP83848JSQ/NOPB is stocked as an active part by multiple authorized distributors, and volume pricing is shown on the listing pages for this MPN. Request current stock, lead time, and volume pricing through the Request a Quote form on this page so the quote reflects live inventory and your required quantities. If your schedule is tight, state the target quantity and date so the supply chain can confirm allocation.
What is the price of the DP83848JSQ/NOPB?
Pricing for the DP83848JSQ/NOPB varies with order quantity and current supply, so the most accurate figure is the one produced for your specific volume and delivery schedule. Submit the Request a Quote form on this page with your target quantity and required date, and you will receive a current quotation for the 40-pin WQFN package with the tape-and-reel or tray packing you need.
Is the DP83848JSQ/NOPB in stock?
The DP83848JSQ/NOPB is listed as an active, orderable part with distributor inventory and standard lead times, and the manufacturer continues to support the DP83848 family. Stock levels change daily across channels, so check live availability and lead time through the Request a Quote form on this page rather than relying on a cached listing. Include your required ship date so partial allocations can be flagged immediately.
Do I need an isolation transformer with the DP83848JSQ/NOPB?
The DP83848JSQ/NOPB requires a 1:1 isolation transformer or an equivalent integrated magnetics module with the correct center-tap bias network to couple to the 10BASE-T and 100BASE-TX medium. The device also requires the standard 49.9 ohm termination resistors and bias resistors set per the typical application circuit in the manufacturer data sheet. Getting the magnetics and termination network right is usually the difference between a clean link and intermittent CRC errors.
What compliance and environmental ratings does the DP83848JSQ/NOPB have?
The DP83848JSQ/NOPB is supplied in a RoHS-compliant, lead-free 40-pin WQFN package, and the commercial-temperature grade is rated 0 C to +70 C. Because the part is a commercial-grade Ethernet transceiver rather than an automotive-qualified device, it is not AEC-Q100 qualified. Confirm REACH and halogen-free status, conflict-minerals declarations, and any extended-temperature options from the manufacturer product page and product compliance documentation.

داتای سەرچاوەی ئەندازیاری بۆ DP83848JSQ/NOPB — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the DP83848JSQ/NOPB when your board needs a single 10/100 Mb/s copper Ethernet port in a commercial-temperature product and you want a proven MII/RMII PHY in a compact 6 x 6 mm WQFN with hardware strap configuration. It is the pragmatic choice for industrial control terminals, printers, building-automation gateways, and bench instruments where cost and board area both matter. Pick the DP83848KSQ/NOPB or DP83848TSQ/NOPB when a different ordering suffix of the same die and footprint better fits your qualification or sourcing needs, and pick the DP83848IRPAP or DP83848IRPAT industrial variants when ambient temperature can exceed 70 C or drop below 0 C. Choose a DP83867-family device instead when you need Gigabit rates, RGMII/SGMII, or automotive qualification, accepting the larger package and the need for a software initialization sequence. Cross-manufacturer PHYs generally change the host interface or the pin arrangement, so treat any substitution as a redesign unless the pin description tables match exactly.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە DP83848KSQ/NOPB DP83848TSQ/NOPB DP83848CSQ/NOPB DP83848IRPAP
Package 40-WQFN (6x6) 40-WQFN (6x6) - same 40-WQFN (6x6) - same 40-WQFN (6x6) - same 40-WQFN (6x6) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Data Rate 10/100 Mbps 10/100 Mbps 10/100 Mbps 10/100 Mbps 10/100 Mbps
Host Interface MII, RMII MII, RMII MII, RMII MII, RMII MII, RMII
Supply Voltage Range 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V
Media Support 10BASE-T, 100BASE-TX, Auto-MDIX 10BASE-T, 100BASE-TX, Auto-MDIX 10BASE-T, 100BASE-TX, Auto-MDIX 10BASE-T, 100BASE-TX, Auto-MDIX 10BASE-T, 100BASE-TX, Auto-MDIX
Number of Pins 40 40 40 40 40

جیاکەرەوە سەرەکییەکان

  • Mature, broadly supported 10/100 PHY with both MII and RMII in a 6 x 6 mm footprint (بەراورد بەKSZ8041RNL)
  • Hardware strap and reset control for deterministic network startup (بەراورد بەDP83867IRRGZR)
  • Low 3.3 V power consumption for embedded form factors (بەراورد بەDP83848MPTBEP)
  • Same-package drop-in path across DP83848 ordering suffixes (بەراورد بەDP83848KSQ/NOPB)

تێبینییەکانی دیزاین

Keep the differential TX/RX pairs from the PHY to the isolation transformer as short, straight, and tightly coupled as the board area allows, and route them on a continuous ground plane with no plane splits underneath. The pair must be a 50-ohm differential impedance design on a 4-layer board with a tightly referenced return path. Avoid routing the pairs adjacent to switching regulators, crystal circuits, or the MII clock, since common-mode coupling on the pair is the usual cause of CRC errors and link flapping in otherwise correct designs.

Decouple the 3.3 V supply pins with 0.1 uF ceramic capacitors placed within a few millimeters of each supply pin, plus bulk capacitance near the magnetics bias network as shown in the typical application circuit in the manufacturer datasheet. The DP83848 requires a clean 3.3 V rail because the PHY's internal regulators and the magnics bias network share it. Estimated: 3.3 V at 92 mA typical gives roughly 0.30 W of input power, so a 3.3 V rail sized for the host processor plus 100 mA headroom covers this device comfortably.

The 40-WQFN (6 x 6 mm) package has an exposed thermal pad that must be soldered to a solid ground pour, ideally with thermal vias into the inner layers. Estimated: at the published 264 mW dissipation and a junction-to-ambient resistance of roughly 40 C/W for a small 6 x 6 mm WQFN on a 4-layer board, the junction rise is only about 11 C, so no heatsink is required and copper pour is adequate. Do not neglect the exposed pad in the footprint stencil design or the part will not solder correctly.

Two mistakes dominate real designs: leaving the configuration strap pins floating or at an undefined level, and mixing up the magnetics bias network. Strap pins are sampled at reset, so each one must be pulled to a defined logic level with a resistor, and the reset pin must be sequenced after the 3.3 V rail is stable. On the medium side, the center-tap bias resistors and the 49.9 ohm termination resistors must match the values in the typical application circuit in the manufacturer datasheet, otherwise the link will fail at 100 Mb/s while working at 10 Mb/s.

MII and RMII timing is sensitive to clock and data skew, so treat the MII TX_CLK and RX_CLK routing as controlled-impedance nets referenced to a solid ground plane, and keep the RMII 50 MHz reference clock source clean and well isolated from switching nodes. When RMII is used, the PHY reset must be released only after the reference clock is stable, otherwise the digital interface may negotiate at an incorrect speed. Reference the interface timing sections in the manufacturer datasheet for setup and hold requirements rather than relying on defaults.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The part is described as RoHS compliant in distributor listings and is supplied in a lead-free 40-WQFN package. REACH, halogen-free, and conflict-minerals declarations are not published in the product listings and should be confirmed from the manufacturer product compliance documentation.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

dp83848jsq nopb dp83848jsq nopb datasheet dp83848jsq datasheet DP83848JSQ/NOPB pinout DP83848JSQ/NOPB price DP83848JSQ/NOPB equivalent DP83848JSQ/NOPB drop-in replacement Texas Instruments DP83848JSQ/NOPB DP83848JSQ 40-WQFN Ethernet PHY DP83848J MII RMII PHY DP83848JSQ/NOPB vs DP83848KSQ/NOPB DP83848JSQ/NOPB application circuit 10/100 Ethernet PHY 3.3V 40 pin QFN DP83848JSQ/NOPB stock what is the DP83848JSQ/NOPB

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments DP83848JSQ/NOPB DP83848J DP83848KSQ/NOPB DP83848TSQ/NOPB DP83848IRPAP DP83867 Ethernet PHY physical layer transceiver network interface controller interface IC semiconductor MII RMII Auto-MDIX 10BASE-T 100BASE-TX Cat-V cable 40-WQFN QFN package family surface mount exposed pad isolation transformer IEEE 802.3 RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ