DP83867IRRGZT - Robust Gigabit Ethernet PHY | Texas Instruments
MPN: DP83867IRRGZT ✓ چالاکDP83867IRRGZT گشتی
A physical-layer transceiver is the active electronics that converts digital Ethernet data into voltage or current signals suitable for transmission over a copper cable, while recovering those signals at the receiving end. The DP83867 belongs to the Ethernet PHY, network-interface IC, communications-semiconductor, and power-management hierarchy. It is used beneath a network controller or processor with an appropriate MAC interface, providing the physical connection to an RJ45 magnetics module or other Ethernet network medium.
The DP83867IR family is positioned for systems requiring high immunity and low-power Ethernet connectivity. The product information identifies a power consumption of 457 mW, integrated MDI termination resistors, programmable RGMII delay modes on both receive and transmit paths, and programmable MII, GMII, and RGMII termination impedance. These features support flexible timing alignment between the PHY and the connected Ethernet controller.
The component also supports cable diagnostics and IEEE 1588 SOF features according to the manufacturer comparison information. These functions can assist commissioning and network timing applications. The RGMII interface is particularly useful for processors, FPGAs, and programmable logic devices that need a high-speed parallel Ethernet connection while keeping the external pin count and PCB area manageable.
Typical installations include industrial Ethernet equipment, factory automation controllers, networked sensors, communications gateways, embedded computers, test equipment, and industrial data-acquisition systems. The industrial-temperature grade makes the device appropriate for equipment where ambient temperature and electrical robustness are important design constraints. A 48-pin VQFN also requires careful PCB layout, thermal management, and high-speed signal-integrity practices.
For a new design, confirm the exact interface mode, strap configuration, clocking method, media configuration, magnetics selection, and firmware or register configuration against the manufacturer datasheet. When replacing an existing PHY, verify the complete pinout, strap behavior, clock source, termination settings, and supported interface mode rather than relying on the package name alone. The DP83867IRRGZT is the industrial-temperature RGZ-package ordering option identified by Texas Instruments.
جێگرەوەکانی جێگۆڕکێ بۆ DP83867IRRGZT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83867IRRGZT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Cable Diagnostics, ESD Protection, Operating Temperature Range.
DP83867CRRGZT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867CSRGZR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867IRRGZR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867IRRGZT تایبەتمەندییەکان
| Product Type | Single-port gigabit Ethernet PHY transceiver |
| Ethernet Standards Supported | 10BASE-Te, 100BASE-TX, 1000BASE-T |
| Host Interface Options | RGMII, MII, GMII, SGMII |
| Number of Ports | 1 port |
| Power Consumption | 457 mW |
| مەودای پلەی گەرمیی کارکردن | -40 °C to 85 °C |
| پاکێج | 48-pin VQFN (RGZ), 7 mm x 7 mm |
| جۆری دامەزراندن | Surface mount |
| Integrated MDI Termination | Yes, integrated MDI termination resistors |
| Programmable RGMII Delay Modes | 16 modes on RX and TX |
| Programmable Interface Termination | Programmable MII, GMII, and RGMII termination impedance |
| ESD Protection | Exceeds 8000 V IEC 61000-4-2 |
| Emissions Compliance | Meets EN55011 Class B emission standards |
| Cable Diagnostics | Supported |
| IEEE 1588 SOF | Supported |
| JTAG Interface | IEEE 1149.1 |
ڕێنمایی ڕێکخستنی پینی DP83867IRRGZT 48-pin vqfn (rgz), 7 mm x 7 mm
ڕێکخستنی پین بۆ DP83867IRRGZT (پاکێجی 48-pin vqfn (rgz), 7 mm x 7 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83867IRRGZT.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DP83867IRRGZT گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Gateway, Factory Automation Controller, Networked Sensor and IoT Controller, FPGA-Based Network Appliance, Test and Measurement Equipment, Networked Data-Acquisition System.
Industrial Ethernet Gateway
The DP83867IRRGZT fits an industrial Ethernet gateway that converts a processor or FPGA data path into 10, 100, or 1000 Mb/s copper Ethernet. Its RGMII option provides a high-speed parallel host interface, while 16 programmable RX and TX delay modes help align edge timing with the connected controller. The documented -40 °C to 85 °C range suits factory-floor equipment, and 457 mW power consumption supports compact embedded designs. Place the PHY close to the Ethernet magnetics and observe controlled-impedance and return-path requirements for RGMII, clocks, and differential pairs.
پێشنیارکراو
Factory Automation Controller
Use the DP83867IRRGZT as the copper-network interface in a PLC, motor controller, or industrial automation node requiring deterministic Ethernet connectivity. Supporting 10BASE-Te, 100BASE-TX, and 1000BASE-T allows one physical design to cover multiple network speeds. The industrial-temperature grade addresses equipment operating from -40 °C to 85 °C, while cable diagnostics help commissioning teams identify wiring faults. RGMII timing remains important, so validate the selected delay mode against the controller clock and trace lengths rather than relying only on nominal pin compatibility.
پێشنیارکراو
Networked Sensor and IoT Controller
The DP83867IRRGZT can add wired Ethernet connectivity to a sensor hub or IoT gateway that previously relied on a low-speed serial link. A single PHY supports 10BASE-Te through 1000BASE-T, while programmable RGMII delay simplifies timing adaptation to FPGAs and embedded processors. Its 48-pin VQFN package keeps the device practical for compact boards, although the 7 mm by 7 mm footprint and dense escape routing require careful land-pattern design. Use isolation and surge-protection components appropriate to the installation environment and verify cable length against the selected Ethernet standard.
پێشنیارکراو
FPGA-Based Network Appliance
An FPGA-based router, protocol converter, or test appliance can use the DP83867IRRGZT when it needs a dedicated 1 Gb/s copper-Ethernet endpoint. RGMII provides a wide parallel interface suited to FPGA I/O, and programmable delay modes on both receive and transmit paths support timing calibration. The device also offers SGMII for systems using serial SerDes links. Keep the RGMII or SGMII routes short, control impedance, and provide a low-noise clock source; the PHY's 457 mW power figure also makes thermal layout relevant in compact or fanless enclosures.
پێشنیارکراو
Test and Measurement Equipment
The DP83867IRRGZT is suitable for Ethernet test instruments, protocol analyzers, and industrial diagnostic equipment that must connect to copper networks at multiple rates. Its 10/100/1000 Mb/s support enables a single interface to address legacy and gigabit test ports, while cable-diagnostic features assist field troubleshooting. The RGMII, MII, GMII, and SGMII choices allow different internal architectures. For laboratory and production equipment, preserve controlled-impedance routing, use solid grounding around the VQFN exposed pad, and check the configuration of termination and delay settings through the manufacturer register documentation.
پێشنیارکراو
Networked Data-Acquisition System
A compact data-acquisition unit can use the DP83867IRRGZT to stream synchronized measurements over a standard copper Ethernet network. RGMII accommodates the throughput of high-speed sensor processing, while the three supported Ethernet rates permit compatibility with existing plant infrastructure. Industrial-temperature operation supports equipment deployed beyond room-temperature environments. Design the analog and digital sections independently, provide clean grounding and local decoupling, and keep the Ethernet differential pairs away from sensitive inputs. Cable diagnostics can help distinguish connector, cable, and link problems during installation and maintenance.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DP83867IRRGZT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DP83867CRRGZT | DP83867CSRGZR | DP83867IRRGZR |
|---|---|---|---|---|
| Package | 48-VQFN (RGZ), 7 mm x 7 mm | 48-VQFN (RGZ), 7 mm x 7 mm | 48-VQFN (RGZ), 7 mm x 7 mm | 48-VQFN (RGZ), 7 mm x 7 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Single-port gigabit Ethernet PHY transceiver | Gigabit Ethernet interface | Gigabit Ethernet PHY | Industrial-temperature gigabit Ethernet PHY |
جیاکەرەوە سەرەکییەکان
- Industrial-temperature ordering option (بەراورد بەDP83867CRRGZT)
- Programming flexibility across RGMII and serial interfaces (بەراورد بەDP83867CSRGZR)
- Integrated copper-interface support (بەراورد بەDP83867IRRGZR)
تێبینییەکانی دیزاین
Use the manufacturer RGZ land pattern and place input and output decoupling capacitors close to their associated supply pins. The 48-pin VQFN requires short, direct escape routes and a continuous ground reference beneath the exposed pad. Match RGMII and clock traces to the board stack-up, keep the Ethernet differential pair geometry consistent, and avoid placing high-current or switching nodes parallel to sensitive receive paths.
Validate RGMII source-synchronous timing with the actual processor or FPGA, PCB stack-up, and clock arrangement. The device provides 16 programmable delay modes on receive and transmit paths, allowing interface timing adjustment without changing the controller. Keep the clock and data traces length-matched within the controller requirements, provide a continuous reference plane, and avoid unnecessary stubs or test-point structures that degrade edge quality.
Do not treat an RGZ suffix match as proof of complete substitution. Review temperature grade, strap behavior, clock source, interface mode, termination settings, firmware configuration, and reset requirements before replacing a component. The target is the industrial-temperature -40 °C to 85 °C option. In particular, verify the exposed-pad connection and the required Ethernet magnetics and termination network against the manufacturer reference design.
Estimated: at the documented 457 mW operating power, the VQFN must transfer heat through its exposed pad and PCB copper. With a 25 °C ambient and an assumed 40 °C/W junction-to-ambient path, the estimated junction temperature would be about 43 °C. Actual rise depends on copper area, board construction, airflow, and neighboring heat sources, so copper spreading and thermal validation remain necessary.
زانیاری پابەندبوون
The device documentation identifies IEC 61000-4-2 ESD protection above 8000 V and EN55011 Class B emission performance. These are product EMC claims rather than a complete material-compliance declaration. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status remain unknown.