Texas Instruments

DP83TG720SWRHATQ1 - 1000BASE-T1 Automotive Ethernet PHY

MPN: DP83TG720SWRHATQ1 ✓ چالاک
36-VQFN (6 x 6 mm) Package
MOQ: 1 |

DP83TG720SWRHATQ1 گشتی

The Texas Instruments DP83TG720SWRHATQ1 is a 1000BASE-T1 automotive Ethernet physical-layer transceiver with RGMII and SGMII MAC interfaces, packaged in a 36-VQFN 6 x 6 mm surface-mount package. It provides the physical-layer functions required to transmit and receive data over shielded or unshielded single twisted-pair cables.

An automotive Ethernet PHY is a semiconductor that converts digital MAC-layer data into signals suitable for an automotive network and converts received cable signals back into digital data. In the technology hierarchy, this 1000BASE-T1 PHY is an Ethernet physical-layer transceiver, an automotive network interface, and a semiconductor designed for vehicle communication systems. IEEE 802.3bp and Open Alliance compliance support standardized 1000BASE-T1 operation.

The device supports RGMII and SGMII interfaces, giving a system designer flexibility when connecting the PHY to an automotive Ethernet MAC or controller. The distributor classification identifies it as a full-duplex, half-duplex transceiver associated with IEEE 802.3. These interface and operating characteristics make the DP83TG720S-Q1 family applicable to vehicle backbone, gateway, domain-controller, and edge-compute networking.

Automotive Ethernet allows high-speed data transfer over a single twisted pair while supporting a lower cable count than conventional multi-pair automotive networks. This can simplify vehicle wiring architectures, although the PHY still requires careful board layout, controlled impedance, robust grounding, and validation against the applicable Open Alliance EMC requirements. The DP83TG720S-Q1 family is intended to implement those physical-layer functions rather than replace the higher-layer Ethernet protocol stack.

Typical implementation places the DP83TG720SWRHATQ1 between an automotive Ethernet MAC and a 1000BASE-T1 cable connection. RGMII provides a parallel digital MAC interface, while SGMII provides a serial interface option. The exact MAC timing, reference-clock, reset, and media-access configuration should be established from the manufacturer datasheet pin description and application guidance for the selected system architecture.

Board design must treat the Ethernet pair as a controlled-impedance differential signal and keep the PHY-side network as short and symmetric as practical. Use the manufacturer’s recommended magnetics and coupling or termination arrangements, observe common-mode-voltage constraints, and provide clean supply rails with local decoupling close to the device. Automotive qualification also requires attention to transient immunity, grounding, EMC margins, and operating-temperature requirements.

This page consolidates the manufacturer’s device description, ordering information, distributor package classification, interface standards, and application implications. It also identifies the unresolved details that must be checked in the datasheet, including the complete pin map, electrical limits, clock requirements, and production quantities.

جێگرەوەکانی جێگۆڕکێ بۆ DP83TG720SWRHATQ1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83TG720SWRHATQ1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Automotive Qualification, Open Alliance Compliance, Package, Cable Support.

Texas Instruments
Product Type: 1000BASE-T1 automotive Ethernet physical-layer transceiver
Automotive Qualification: Automotive-grade Q1 product family
Open Alliance Compliance: Open Alliance EMC and interoperability specifications
بەراوردکردن لەگەڵ DP83TG720SWRHATQ1 →
Texas Instruments
Product Type: Automotive Ethernet PHY Transceiver
Package: VQFN-36 (6x6 mm) with exposed pad
بەراوردکردن لەگەڵ DP83TG720SWRHATQ1 →
Texas Instruments
Product Type: 1000BASE-T1 automotive Ethernet physical-layer transceiver
Automotive Qualification: AEC-Q100
Open Alliance Compliance: Compliant
بەراوردکردن لەگەڵ DP83TG720SWRHATQ1 →

DP83TG720RWRHARQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 36-VQFN
1000BASE-T1 automotive Ethernet physical-layer transceiver · DP83TG720R-Q1 · 1000BASE-T1 · RGMII · Unshielded or shielded single twisted pair · IEEE 802.3bp · Open Alliance EMC and interoperability specifications · Full and half duplex

پەیوەندی بۆ نرخ

بینینی داتاشیت →

DP83TG720RWRHATQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 36-VQFN
Automotive Ethernet PHY Transceiver · 1000BASE-T1 PHY with RGMII MAC interface · IEEE 802.3bp, Open Alliance TC10 · 1000 Mbps (1000BASE-T1); 100 Mbps (100BASE-T1 legacy via DP83TG720S compatibility) · RGMII · 1.8 V / 2.5 V / 3.3 V (multi-rail) · 1 · Full, Half

پەیوەندی بۆ نرخ

بینینی داتاشیت →

DP83TG720SWRHATQ1 تایبەتمەندییەکان

Product Type 1000BASE-T1 Automotive Ethernet PHY
Ethernet Standard IEEE 802.3bp
Open Alliance Compliance Open Alliance compliant
MAC Interface RGMII and SGMII
Transceiver Mode Full-duplex and half-duplex
Cable Support Shielded or unshielded single twisted-pair cable
پاکێج 36-VQFN (6 x 6 mm)
جۆری دامەزراندن Surface mount
Automotive Qualification AEC-Q100 qualified device family
EMC Compliance Open Alliance EMC compliant

ڕێنمایی ڕێکخستنی پینی DP83TG720SWRHATQ1 36-vqfn (6 x 6 mm)

ڕێکخستنی پین بۆ DP83TG720SWRHATQ1 (پاکێجی 36-vqfn (6 x 6 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 36-vqfn (6 x 6 mm) بۆ DP83TG720SWRHATQ1

هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83TG720SWRHATQ1.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

DP83TG720SWRHATQ1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Ethernet Backbone, Vehicle Domain Controller, Automotive Gateway, Vehicle Edge Computer, Automotive Sensor and Actuator Network, Vehicle Infotainment System.

🚗

Automotive Ethernet Backbone

The DP83TG720SWRHATQ1 is suitable for an automotive Ethernet backbone link that carries data over one twisted pair. Its 1000BASE-T1 physical-layer operation, IEEE 802.3bp compliance, and RGMII or SGMII connection to an automotive MAC support high-bandwidth in-vehicle networking. According to the Texas Instruments manufacturer datasheet, the device also addresses shielded or unshielded cable options. The design must still validate the cable, connector, automotive Ethernet magnetics, EMC behavior, and fault injection requirements for the specific vehicle network.

🖥️

Vehicle Domain Controller

A domain controller can use the DP83TG720SWRHATQ1 as the 1000BASE-T1 physical layer between its Ethernet MAC and an in-vehicle network. RGMII permits a parallel connection to a compatible MAC, while SGMII can reduce the number of MAC-side signals. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, both interfaces are supported. System designers must coordinate MAC timing, reference-clock generation, reset behavior, protocol configuration, and thermal conditions before selecting the operating mode.

🌐

Automotive Gateway

The DP83TG720SWRHATQ1 is appropriate for a gateway that links vehicle network segments through a 1000BASE-T1 physical layer. A single twisted pair can help reduce wiring complexity while preserving high-speed Ethernet connectivity. According to the Texas Instruments manufacturer datasheet, the PHY supports IEEE 802.3bp, Open Alliance EMC requirements, and both RGMII and SGMII MAC connections. The gateway implementation must also account for network redundancy, cable faults, EMI containment, grounding, and the electromagnetic environment around the ECU enclosure.

🔧

Vehicle Edge Computer

The DP83TG720SWRHATQ1 can connect an edge-computing ECU to a 1000BASE-T1 vehicle network while leaving higher-layer services to an embedded MAC and protocol stack. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the PHY supplies the physical-layer functions required for single-pair data transmission and reception. The MAC interface choice influences board area and signal-integrity work: RGMII uses parallel signals, whereas SGMII uses a serial interface and requires careful clock and impedance implementation.

🧩

Automotive Sensor and Actuator Network

The DP83TG720SWRHATQ1 can provide the physical layer for an Ethernet-connected sensor, actuator, or intelligent peripheral linked to an automotive Ethernet network. Its 1000BASE-T1 capability supports high-speed communication over a single pair, and the RGMII and SGMII interfaces offer flexibility for different embedded controllers. According to the Texas Instruments manufacturer datasheet, the family supports shielded and unshielded twisted-pair cabling. Deployment decisions should include cable reach, connector definition, isolation strategy, EMC limits, and synchronization requirements of the endpoint device.

📺

Vehicle Infotainment System

The DP83TG720SWRHATQ1 is applicable to an infotainment or communications ECU that exchanges data with other vehicle systems over 1000BASE-T1. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the PHY supports RGMII and SGMII, enabling connection to an automotive Ethernet MAC in different architectures. For an infotainment design, assess EMI proximity to display and audio power systems, implement the manufacturer reference network and magnetics arrangement, and verify timing and error recovery across the complete cable and connector path.

What is the DP83TG720SWRHATQ1?
The DP83TG720SWRHATQ1 is a Texas Instruments 1000BASE-T1 automotive Ethernet physical-layer transceiver with RGMII and SGMII MAC interfaces. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, it supplies the physical-layer functions needed to transmit and receive data over shielded or unshielded single twisted-pair cables and is packaged in a 36-VQFN 6 x 6 mm package.
What standards does the DP83TG720SWRHATQ1 support?
The DP83TG720SWRHATQ1 is identified as an IEEE 802.3bp and Open Alliance compliant automotive Ethernet PHY. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the DP83TG720 family is also compliant with Open Alliance EMC requirements. These standards cover the physical layer and EMC behavior needed for 1000BASE-T1 links over a single twisted pair.
Which MAC interfaces are available on the DP83TG720SWRHATQ1?
The DP83TG720SWRHATQ1 provides RGMII and SGMII MAC interfaces through its xMII flexibility. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, RGMII offers a parallel digital interface, while SGMII offers a serial interface. The appropriate choice depends on the automotive Ethernet MAC, clocking architecture, trace constraints, and system validation requirements.
What package is used by the DP83TG720SWRHATQ1?
The DP83TG720SWRHATQ1 uses a 36-VQFN package measuring 6 x 6 mm. According to the Texas Instruments ordering information, the exact ordering code identifies a surface-mount automotive variant of the DP83TG720S-Q1 family. Use the package drawing, land pattern, pin table, and exposed-pad requirements in the manufacturer datasheet before releasing a PCB footprint.
Where can I download the DP83TG720SWRHATQ1 datasheet PDF?
The official DP83TG720S-Q1 datasheet can be accessed through the Texas Instruments product page and ordering information for DP83TG720SWRHATQ1. According to the Texas Instruments manufacturer documentation, the document contains the device functions, electrical characteristics, application information, and package details. Download the current revision directly from the official product page to ensure that design values and revision history remain current.
Where can I find the DP83TG720SWRHATQ1 pinout?
The DP83TG720SWRHATQ1 pinout is defined in the pin-configuration table and package drawing of the Texas Instruments manufacturer datasheet. According to the manufacturer documentation, the device uses a 36-VQFN package with an exposed thermal pad. Assign PCB nets from the numbered datasheet pin table rather than relying on package orientation or a generic diagram.
Can the DP83TG720SWRHATQ1 support automotive backbone networking?
The DP83TG720SWRHATQ1 is suitable for automotive Ethernet links that use a 1000BASE-T1 physical layer over one twisted pair. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the device is an IEEE 802.3bp-compliant automotive PHY with RGMII and SGMII connectivity. Suitability still depends on the complete vehicle network, EMC validation, cable, magnetics, and system timing.
Is the DP83TG720SWRHATQ1 suitable for a vehicle domain controller?
The DP83TG720SWRHATQ1 can serve as the 1000BASE-T1 physical layer beside an automotive Ethernet MAC in a domain-controller architecture. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, its RGMII and SGMII interfaces support different MAC connection methods. The MAC implementation, protocol stack, clock source, thermal environment, and cable qualification must also support the intended link.
When should I choose the DP83TG720SWRHATQ1 over another automotive Ethernet PHY?
Choose the DP83TG720SWRHATQ1 when the design specifically requires a 1000BASE-T1 PHY with RGMII and SGMII options in the 36-VQFN 6 x 6 mm package. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the family is compliant with IEEE 802.3bp and Open Alliance requirements. Selection should also account for cable, magnetics, clocking, EMC, temperature, and qualification needs.
What is the difference between RGMII and SGMII for the DP83TG720SWRHATQ1?
RGMII is a parallel MAC interface, while SGMII is a serial MAC interface supported by the DP83TG720SWRHATQ1. According to the Texas Instruments manufacturer datasheet for DP83TG720S-Q1, the device provides xMII flexibility through these interfaces. RGMII can simplify connection to a compatible parallel MAC, whereas SGMII can reduce interface pin count but requires suitable source-synchronous signaling and clocking.
What can replace the DP83TG720SWRHATQ1?
No verified pin-to-pin drop-in replacement for the DP83TG720SWRHATQ1 was identified. According to the Texas Instruments product information, the device is the 36-VQFN 6 x 6 mm ordering variant of the DP83TG720S-Q1 family. A replacement must match the 36-pin footprint, RGMII and SGMII functions, IEEE 802.3bp behavior, automotive qualification, and EMC requirements.
Is a non-Texas Instruments equivalent available for the DP83TG720SWRHATQ1?
A verified non-Texas Instruments drop-in equivalent has not been established for the DP83TG720SWRHATQ1. According to the available manufacturer information, the device combines a 36-VQFN 6 x 6 mm package with RGMII and SGMII, IEEE 802.3bp compliance, and automotive Open Alliance EMC requirements. Any candidate should be treated as a redesign unless its manufacturer explicitly confirms pin and functional compatibility.
How should the DP83TG720SWRHATQ1 Ethernet pair be routed?
Route the DP83TG720SWRHATQ1 Ethernet pair as a length-matched, tightly coupled differential pair on a continuous reference plane. According to the Texas Instruments manufacturer application guidance for DP83TG720S-Q1, the PHY-side implementation must follow the device’s reference network and layout requirements. Keep the pair away from switching nodes and noisy return paths, and validate the complete connector, cable, and magnetics interface.
Where can I buy the DP83TG720SWRHATQ1 and check its price?
Use the Request a Quote form on this page to request the current DP83TG720SWRHATQ1 price, stock position, minimum order quantity, and lead time. According to the Texas Instruments ordering information, the part is available as the SWRHATQ1 ordering code. Quote responses should confirm the exact suffix, package, reel quantity, delivery date, and any traceability requirements.
How much is the DP83TG720SWRHATQ1 and how long is the lead time?
Current price and lead time for the DP83TG720SWRHATQ1 should be requested through the Request a Quote form on this page. According to the Texas Instruments ordering information, the manufacturer identifies the exact SWRHATQ1 orderable variant. The quotation can confirm quantity breaks, production reel quantity, current stock, lead time, and shipment terms without relying on a stale listing value.

داتای سەرچاوەی ئەندازیاری بۆ DP83TG720SWRHATQ1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the DP83TG720SWRHATQ1 for a new 1000BASE-T1 automotive Ethernet design that specifically uses the Texas Instruments DP83TG720S-Q1 family, a 36-VQFN 6 x 6 mm PCB footprint, and either an RGMII or SGMII MAC interface. Its IEEE 802.3bp and Open Alliance positioning is appropriate for vehicle networks using shielded or unshielded single twisted-pair cables. Confirm the ordering suffix, electrical limits, pin assignment, clocking, reference network, and automotive qualification before schematic release. No drop-in replacement has been verified, so a different PHY should be treated as a redesign unless its manufacturer explicitly confirms pin compatibility and equivalent functions. The related DP83TG720SWRHARQ1 listing may assist family identification, but its exact package, qualification, and configuration must be checked before substitution.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە
Brand Texas Instruments
Package 36-VQFN (6 x 6 mm)
Product Type 1000BASE-T1 Automotive Ethernet PHY
Ethernet Standard IEEE 802.3bp
MAC Interface RGMII and SGMII
Cable Support Shielded or unshielded single twisted-pair cable
Transceiver Mode Full-duplex and half-duplex
EMC Compliance Open Alliance EMC compliant
Automotive Qualification AEC-Q100 qualified device family
Mounting Type Surface mount

جیاکەرەوە سەرەکییەکان

  • Single-pair 1000BASE-T1 physical layer (بەراورد بەDP83TG720SWRHARQ1)
  • Dual MAC-interface architecture (بەراورد بەDP83TG720SWRHARQ1)
  • Automotive standards alignment (بەراورد بەDP83TG720SWRHARQ1)

تێبینییەکانی دیزاین

Implement the 1000BASE-T1 link using the manufacturer’s reference network and magnetics arrangement. Keep the Ethernet pair continuous, closely coupled, and referenced to a solid plane, while keeping PHY-side components and test points consistent with the recommended layout. Avoid placing high-speed switching nodes beneath the pair, and preserve symmetry between the two conductors to minimize radiated emissions and susceptibility to external interference.

Select RGMII or SGMII according to the MAC interface and complete PCB constraint set. RGMII provides parallel data and control signals, so maintain the specified trace topology, length relationships, impedance, and clock-signal treatment. SGMII reduces parallel wiring but still requires controlled impedance and carefully aligned reference clock and serial data. Validate both interfaces with the selected MAC and representative automotive cables before production release.

Separate the 1000BASE-T1 copper connection from sensitive analog, audio, and high-current switching paths. Use a continuous reference plane without split crossings, maintain the required clearances defined by the manufacturer layout guidance, and place the PHY close to the cable-side interface components. Correct placement reduces common-mode conversion, radiated emissions, and susceptibility to transient events encountered in an automotive environment.

Do not treat a generic 36-VQFN footprint or another 1000BASE-T1 PHY as a confirmed substitute. A valid drop-in replacement must match the numbered pins, exposed-pad connection, RGMII and SGMII functions, electrical levels, clocking, reset behavior, regulatory constraints, and automotive qualification. Confirm the complete manufacturer ordering code and obtain the current datasheet before substituting any part or modifying the PCB.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The DP83TG720S-Q1 ordering information identifies an automotive Ethernet PHY with a Q1 suffix, and the family is associated with Open Alliance EMC compliance. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not confirmed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

DP83TG720SWRHATQ1 datasheet DP83TG720SWRHATQ1 pinout DP83TG720SWRHATQ1 datasheet pdf DP83TG720SWRHATQ1 equivalent DP83TG720SWRHATQ1 replacement DP83TG720SWRHATQ1 cross reference DP83TG720SWRHATQ1 footprint DP83TG720SWRHATQ1 schematic DP83TG720SWRHATQ1 price DP83TG720SWRHATQ1 stock Texas Instruments DP83TG720SWRHATQ1 DP83TG720SWRHATQ1 36-VQFN DP83TG720SWRHATQ1 RGMII SGMII DP83TG720SWRHATQ1 automotive Ethernet

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments DP83TG720SWRHATQ1 DP83TG720S-Q1 DP83TG720SWRHARQ1 1000BASE-T1 automotive Ethernet Ethernet physical-layer transceiver Ethernet PHY physical-layer device network interface IC RGMII SGMII xMII IEEE 802.3bp Open Alliance AEC-Q100 single twisted-pair cable shielded twisted pair unshielded twisted pair 36-VQFN QFN family surface-mount package automotive domain controller differential pair Open Alliance EMC
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ