Texas Instruments

INA103KU - Low-Noise Instrumentation Amplifier | Texas Instruments

MPN: INA103KU ✓ چالاک
9 V to 25 V Vdss 16-SOIC Package
MOQ: 1 |

INA103KU گشتی

The Texas Instruments INA103KU is a low-noise, low-distortion monolithic instrumentation amplifier with one amplifier circuit, a 16-SOIC package, a gain bandwidth of 6 MHz, and a slew rate of 15 V/s. It operates from a single supply between 9 V and 25 V and provides near-theoretical noise performance for source impedances near 200 ohms.

An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input terminals while rejecting common-mode signals. Its internal gain network and feedback architecture provide high input impedance, accurate differential gain, and better rejection of shared interference than a general-purpose operational amplifier. The INA103KU is therefore positioned between precision operational amplifiers and higher-cost precision measurement amplifiers.

The INA103 uses current-feedback circuitry to achieve a 6 MHz gain-bandwidth product and a 15 V/s slew rate. Its low-noise design is suitable for extracting weak signals without requiring a high signal frequency. The manufacturer identifies balanced, low-impedance microphone signals as a primary use case, while the differential input architecture also supports sensor bridges, current measurement, laboratory instrumentation, and industrial receiver front ends.

The component supports single-ended and differential signal arrangements and accommodates source impedances around 200 ohms with near-theoretical noise performance. Its maximum output offset voltage listed for the INA103KU is 250 µV. Because its supply range is 9 V to 25 V, the device is intended for higher-voltage analog systems rather than low-voltage mixed-signal rails where a modern rail-to-rail amplifier may be more appropriate.

Typical applications include balanced low-impedance microphones, audio equipment, industrial sensor interfaces, pressure and strain-gauge bridges, current shunts, and precision measurement front ends. The 16-SOIC package provides a conventional surface-mount footprint and supports integration into analog signal-conditioning boards, instrument preamplifiers, and multi-channel measurement systems.

Designers should verify gain settings, source impedance, bandwidth, output swing, and supply headroom against the manufacturer datasheet. Input and output filtering should be selected for the source impedance and signal bandwidth, while adequate bypassing should be placed close to the supply pins to preserve low-noise operation.

This product page combines manufacturer specifications, application guidance, package information, and verified drop-in family options. It also highlights the INA103KU's operating envelope, making it easier to compare it with other instrumentation amplifiers before committing to a high-voltage analog design.

جێگرەوەکانی جێگۆڕکێ بۆ INA103KU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA103KU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Bandwidth, Input Offset Voltage, Product Type, Slew Rate.

Texas Instruments
Package: 16-SOIC (DW / SOL-16)
Bandwidth: 25 kHz
Input Offset Voltage: 25 uV max
بەراوردکردن لەگەڵ INA103KU →
Texas Instruments
Package: 16-pin SOIC, 7.50 mm width
Bandwidth: 300 kHz
Input Offset Voltage: 250 uV
بەراوردکردن لەگەڵ INA103KU →
Texas Instruments
Package: 16-pin SOIC (DW)
Bandwidth: 6 MHz
Product Type: Low-noise, low-distortion instrumentation amplifier

INA103UA

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-SOIC
Same INA103 electrical performance and 16-SOIC footprint; ordering-code difference only, with 0% change in the listed core ratings.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA103UP

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-SOIC
Same INA103 electrical performance and 16-SOIC footprint; ordering-code difference only, with 0% change in the listed core ratings.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA103UK

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-SOIC
Same INA103 electrical performance and 16-SOIC footprint; ordering-code difference only, with 0% change in the listed core ratings.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA103KU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Monolithic instrumentation amplifier
Amplifier Circuit Count 1 circuit
پاکێج 16-SOIC
جۆری دامەزراندن Surface mount
Supply Voltage Range 9 V to 25 V
Gain-Bandwidth Product 6 MHz
Slew Rate 15 V/s
Input Offset Voltage 250 µV maximum
Architecture Current-feedback circuitry
Differential Input Support Yes
Single-Ended Input Support Yes
Recommended Source Impedance 200 ohm
Noise Performance Near-theoretical limit at a 200 ohm source impedance
Signal Type Low-level differential audio and sensor signals

ڕێنمایی ڕێکخستنی پینی INA103KU 16-soic

ڕێکخستنی پین بۆ INA103KU (پاکێجی 16-soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 16-soic بۆ INA103KU

هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA103KU.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

INA103KU گونجاوە بۆ 6 بەکارھێنانs: Balanced Microphone Preamplifier, Industrial Sensor Front End, Precision Current Measurement, Audio Equipment Signal Conditioning, Laboratory Instrumentation, Low-Level Receiver Front End.

🎧

Balanced Microphone Preamplifier

The INA103KU fits low-level microphone front ends because its current-feedback instrumentation-amplifier architecture provides a 6 MHz gain-bandwidth product and a 15 V/s slew rate while maintaining low noise for source impedances around 200 ohms. It can accept a differential microphone signal and reject common-mode interference present on both input conductors. The single 9 V to 25 V supply also provides useful output headroom for traditional professional-audio signal levels. The primary design constraints are the selected gain, input and feedback stability, and sufficient output swing. Keep the input route short, place the gain-setting components close to the amplifier, and use the manufacturer gain-table and stability guidance for the actual microphone impedance.

🏭

Industrial Sensor Front End

The INA103KU is suitable for conditioning weak differential sensor outputs when the system operates from a 9 V to 25 V analog supply. Its monolithic instrumentation-amplifier configuration simplifies the conversion of a small differential signal into a larger single-ended signal for downstream conversion or control. The 6 MHz bandwidth provides substantial headroom beyond many sensor-bandwidth requirements, while the 15 V/s slew rate supports faster transient events than a slow precision-only amplifier. For strain gauges, pressure elements, or resistive bridges, verify the bridge excitation scheme, common-mode voltage, gain, and output range against the INA103 datasheet before applying power.

⚡

Precision Current Measurement

A low-value shunt can be placed between the INA103KU differential inputs to measure current without placing the measurement path directly in the high-voltage conductor. The instrumentation-amplifier arrangement rejects common-mode voltage shared by the shunt connections, while the 6 MHz gain-bandwidth product and 15 V/s slew rate support dynamic current signals. The 250 µV maximum input offset establishes the basic sensitivity limit that must be considered with shunt resistance and gain. Choose the external gain network and output filtering for the expected current range, and verify that the common-mode input and output voltages remain within the electrical limits stated in the manufacturer datasheet.

🎧

Audio Equipment Signal Conditioning

The INA103KU can form the differential input stage of a professional audio preamplifier, line receiver, or low-level audio conditioner. Its low-noise design, 6 MHz bandwidth, and 15 V/s slew rate provide a strong combination of signal fidelity and dynamic response, particularly for balanced sources with impedance near 200 ohms. The 9 V to 25 V operating range fits traditional analog equipment more closely than a 3.3 V or 5 V rail-to-rail device. Designers should account for input-referenced noise, gain error, output swing, and stable feedback components. A balanced output stage may be required if the downstream subsystem does not accept a single-ended signal.

🖥️

Laboratory Instrumentation

The INA103KU can amplify small differential signals in laboratory instrumentation where low noise, bandwidth, and adjustable signal gain are more important than operation from a very low supply voltage. Its 6 MHz gain-bandwidth product is suitable for many sensor-bandwidth and audio-style measurement systems, while the current-feedback architecture is intended to provide strong dynamic response. For bench instruments, the 16-SOIC package makes the device practical to assemble on analog measurement boards with conventional surface-mount layout. Verify resistor accuracy, input protection, common-mode range, output loading, and calibration stability before using it as the front end of a precision measurement chain.

🌐

Low-Level Receiver Front End

The INA103KU is appropriate as the first amplification stage in a receiver handling small differential signals embedded in a larger common-mode environment. Its instrumentation-amplifier topology targets common-mode rejection, and the 6 MHz bandwidth offers useful margin for communications, control, or sensing signals without requiring an extremely wide-band amplifier. The 15 V/s slew rate helps preserve waveform shape when large low-frequency components accompany the target signal. Because the INA103KU is not a rail-to-rail low-voltage part, the receiver must provide a compatible 9 V to 25 V supply. Confirm input bias-current effects, source impedance, gain limits, and output compliance in the manufacturer datasheet.

What is the INA103KU?
The INA103KU is a Texas Instruments low-noise, low-distortion monolithic instrumentation amplifier packaged in a 16-SOIC. According to the INA103 manufacturer datasheet, it uses current-feedback circuitry, has a 6 MHz gain-bandwidth product, and is designed to recover low-level differential signals such as those produced by balanced, low-impedance microphones.
What is the operating voltage of INA103KU?
The INA103KU operates from a single supply of 9 V to 25 V. This supply range distinguishes it from low-voltage, rail-to-rail instrumentation amplifiers and makes it appropriate for audio, industrial, and instrumentation circuits that provide a higher analog supply voltage. Confirm the required headroom for the selected gain and output signal in the manufacturer datasheet.
What are the key specifications of INA103KU that engineers should know?
The INA103KU combines a 6 MHz gain-bandwidth product, a 15 V/s slew rate, and a 250 µV maximum input offset voltage in a 16-SOIC package. According to the INA103 manufacturer datasheet, its current-feedback architecture supports wide bandwidth and dynamic response, while its noise performance approaches the theoretical limit for a 200 ohm source impedance.
Where can I download the INA103KU datasheet PDF?
The official INA103KU datasheet is available from the Texas Instruments INA103 product page and the manufacturer PDF at https://www.ti.com/lit/ds/symlink/ina103.pdf. Use the pin-description table, electrical-characteristics table, typical application circuit, and gain-setting section when assigning PCB connections and selecting external resistors.
Where can I find the INA103KU pinout?
Use the pin-description table in the official Texas Instruments INA103 datasheet to identify the INA103KU connections in the 16-SOIC package. The pinout diagram is also shown through the package graphic on this product page. Confirm pin numbering against the physical package orientation before routing power, feedback, and signal connections.
Can the INA103KU amplify balanced microphone signals?
Yes. The INA103KU is specifically suited to balanced, low-impedance microphone signals because its differential input can reject common-mode interference while preserving low-level audio information. The manufacturer datasheet reports near-theoretical noise performance for source impedances near 200 ohms and identifies 6 MHz bandwidth and 15 V/s slew rate as key dynamic-response characteristics.
What can replace the INA103KU?
The closest same-family drop-in choices are INA103UA and INA103UP, both of which retain the INA103 electrical architecture and use the same 16-SOIC footprint for pin-compatible replacement. Cross-brand drop-in replacements are not listed because the available cross-reference records do not establish package, pinout, gain, supply, bandwidth, and offset compatibility for a specific competitor MPN.
Is INA103KU the same as INA103UA?
The INA103KU and INA103UA are same-brand INA103 family versions with matching 16-SOIC packaging and matching core performance characteristics, making INA103UA a pin-compatible drop-in option. Exact ordering, temperature, and lifecycle conditions should still be checked against the manufacturer product page before production release.
What is the best Analog Devices equivalent for INA103KU?
An Analog Devices drop-in equivalent cannot be selected confidently from the available records without a confirmed MPN and complete pinout comparison. The cross-reference search identifies Analog Devices as a possible source of alternatives, but it does not establish that any particular part matches the INA103KU's 16-SOIC footprint, 9 V to 25 V supply range, 6 MHz bandwidth, and gain network.
When should I choose INA103KU over INA101KU/1K?
Choose the INA103KU when the circuit needs the INA103 family's low-noise, low-distortion, current-feedback performance and broader gain flexibility. INA101KU/1K is a fixed-gain alternative with different gain and bandwidth characteristics, so it should be selected only when its exact gain, supply, output swing, and stability behavior meet the signal-chain requirements.
When should I choose INA103KU over INA105KU/2K5?
Choose the INA103KU when adjustable or application-specific gain is more useful than the INA105KU/2K5's fixed-gain approach. The two families are not interchangeable merely because both are instrumentation amplifiers; verify gain accuracy, noise, bandwidth, input common-mode range, supply range, and output swing for the selected replacement.
Where can I buy INA103KU online?
Use the Request a Quote form on this page to request current INA103KU availability, MOQ, and lead time from XAIPART. The component is a Texas Instruments 16-SOIC instrumentation amplifier, and an exact orderable MPN check is necessary because package, temperature, and reel configuration can affect procurement.
What is the price of INA103KU?
Use the Request a Quote form on this page for the current INA103KU quotation. Pricing depends on order quantity, package configuration, and market conditions, and the structured price evidence for this exact MPN does not contain qualifying quantity-break pricing. XAIPART will confirm the current unit price and scheduled order quantity.
What is the lead time for INA103KU?
Request the current lead time through the Request a Quote form on this page. Lead time depends on the exact ordering code, reel configuration, order quantity, and current manufacturer channel availability. The INA103 family is listed as an active product, but a production schedule should always be confirmed for the required configuration.
Is INA103KU in stock?
Request current stock confirmation through the Request a Quote form on this page. The part is an active Texas Instruments INA103 family device in a 16-SOIC package, but availability can vary by exact suffix, reel configuration, and order quantity. Use the quotation form to obtain the latest allocation and delivery information.
What design considerations matter when using INA103KU?
The INA103KU requires sufficient supply headroom, correct gain-resistor selection, and layout that minimizes noise pickup and instability. According to the INA103 manufacturer datasheet, the current-feedback architecture is optimized for source impedances around 200 ohms. Place bypass capacitors near the supply pins, keep input and feedback traces short, and verify stability with the intended source impedance and gain.

داتای سەرچاوەی ئەندازیاری بۆ INA103KU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the INA103KU when the design needs a low-noise, low-distortion instrumentation amplifier with a 9 V to 25 V supply, 6 MHz gain-bandwidth product, and 15 V/s slew rate. It is especially suitable for balanced microphones, industrial sensors, shunts, and laboratory receivers whose source impedance is near 200 ohms. Select INA103UA or INA103UP when an equivalent INA103 family ordering option is preferable for procurement or assembly, after confirming the exact suffix, temperature grade, and lifecycle status. INA101KU/1K is more appropriate when a fixed-gain INA101 solution meets the bandwidth and accuracy requirements, while INA105KU/2K5 may be preferred when its fixed gain suits the design. Neither fixed-gain family should be treated as a footprint-only replacement without checking gain, supply range, common-mode range, output swing, noise, bandwidth, and stability. The INA103KU is the stronger general-purpose choice within its family when gain flexibility and low-level signal performance are the priorities.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA103UA INA103UP INA103UK
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Product Type Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier Monolithic instrumentation amplifier
Amplifier Circuit Count 1 circuit 1 circuit 1 circuit 1 circuit
Supply Voltage Range 9 V to 25 V 9 V to 25 V 9 V to 25 V 9 V to 25 V
Gain-Bandwidth Product 6 MHz 6 MHz 6 MHz 6 MHz
Slew Rate 15 V/s 15 V/s 15 V/s 15 V/s
Input Offset Voltage 250 µV maximum 250 µV maximum 250 µV maximum 250 µV maximum
Architecture Current-feedback circuitry Current-feedback circuitry Current-feedback circuitry Current-feedback circuitry
Recommended Source Impedance 200 ohm 200 ohm 200 ohm 200 ohm

جیاکەرەوە سەرەکییەکان

  • Higher-voltage low-noise instrumentation-amplifier platform (بەراورد بەINA101KU/1K)
  • Flexible gain design versus a fixed-gain replacement (بەراورد بەINA105KU/2K5)
  • Direct same-package family replacement (بەراورد بەINA103UA)

تێبینییەکانی دیزاین

Keep the differential input paths, gain-setting components, and feedback components close to the INA103KU. Route the two input conductors as a compact, symmetric pair and keep them away from switching nodes and high-current return paths. This is particularly important because the INA103 is optimized for low-level differential signals and source impedances around 200 ohms, where parasitic pickup and unequal routing can degrade common-mode rejection.

Provide a stable single supply within the 9 V to 25 V operating range and place the required bypass capacitors close to the supply pins. Check input and output voltage limits for the selected gain, because a differential input can experience a common-mode component even when its differential amplitude is small. Use the manufacturer's electrical-characteristics limits for common-mode range, output swing, supply current, and power dissipation before finalizing the rail voltage.

Do not assume that the 6 MHz gain-bandwidth product is the usable closed-loop bandwidth at every gain. The achievable bandwidth depends on the selected gain, external resistor values, source impedance, load, and feedback topology. Follow the INA103 datasheet gain table and stability guidance, use the recommended resistor arrangements, and evaluate source impedance and capacitive loading before treating the device as a general-purpose wideband amplifier.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The INA103KU is an industrial analog instrumentation amplifier; automotive qualification is not indicated. Confirm RoHS, REACH, lead-free, and halogen-free status for the exact ordering configuration with the manufacturer.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

INA103KU datasheet INA103KU pinout INA103KU datasheet pdf INA103KU specifications INA103KU equivalent INA103KU replacement INA103KU cross reference INA103KU vs INA101KU INA103KU vs INA105KU INA103KU price INA103KU stock Texas Instruments INA103KU INA103KU application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA103KU INA103UA INA103UP INA103UK INA103 instrumentation amplifier monolithic instrumentation amplifier current-feedback amplifier signal amplifier analog integrated circuit semiconductor 16-SOIC SOIC family surface-mount package low-noise amplifier low-distortion amplifier differential input common-mode rejection gain-bandwidth product slew rate balanced microphone preamplifier industrial sensor interface current shunt measurement 9 V to 25 V supply
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ