Texas Instruments

INA111AU - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

MPN: INA111AU ✓ چالاک
500 uV maximum Vdss 20 pA maximum Id 16-pin SOIC (DW) Package
MOQ: 1 |

INA111AU گشتی

The Texas Instruments INA111AU is a high-speed FET-input instrumentation amplifier with 2 MHz bandwidth, 17 V/us slew rate, and a 16-pin SOIC package. It is designed for precision signal conditioning where low input bias current, high common-mode rejection, and fast settling are important. The device uses a current-feedback architecture and provides a gain range of 1 to 1000 through an external gain-setting resistor.

An instrumentation amplifier is a differential analog amplifier designed for measuring small differential signals while rejecting large common-mode voltages. It is commonly used to amplify sensor outputs, bridge signals, strain-gauge outputs, and low-level biological signals. The INA111AU belongs to the instrumentation amplifier hierarchy, which provides differential input handling and gain control in a compact analog front end.

The FET input stage reduces input bias current to 20 pA maximum, making the INA111AU suitable for high-impedance sources. Its maximum input offset voltage is 500 uV, and its maximum input offset voltage drift is 5 uV/C. The minimum common-mode rejection ratio is 106 dB. The device offers a 2 MHz bandwidth and 17 V/us slew rate, supporting faster response than many general-purpose precision instrumentation amplifiers.

The INA111AU uses a three-operamplifier instrumentation-amplifier architecture with laser-trimmed resistors. A single external resistor sets the closed-loop gain, allowing gain values from 1 to 1000 when the specified gain-setting resistor is used. This combination of differential input, adjustable gain, and high input impedance makes the device suitable for conditioning signals from pressure, temperature, current, and resistive bridge sensors.

Typical applications include bridge-transducer amplification, portable measurement systems, instrumentation interfaces, industrial sensor conditioning, and precision data-acquisition front ends. The low bias current helps preserve sensor-source accuracy, while the 106 dB minimum common-mode rejection helps suppress noise and supply disturbances that are common to both differential inputs.

Designers should keep input and feedback traces short, provide suitable bypassing close to the power pins, and verify the external gain resistor against the datasheet gain equation. Input common-mode and output swing limits must be checked at the selected supply voltage and gain. The manufacturer datasheet should be used for the complete pin description, recommended application circuit, and gain-setting calculations.

This product page combines the manufacturer specifications, verified sourcing information, package details, application guidance, and engineering-oriented design notes. It helps engineers evaluate the INA111AU for high-impedance measurement circuits while identifying the key electrical limits that determine signal fidelity and system compatibility.

جێگرەوەکانی جێگۆڕکێ بۆ INA111AU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA111AU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Gain Range, Package, Operating Temperature Range, Amplifier Type, Bandwidth.

Texas Instruments
Gain Range: 1 to over 1000
Package: 16-SOIC
بەراوردکردن لەگەڵ INA111AU →
Texas Instruments
Gain Range: 1 to 10,000
Package: 16-pin SOIC, 3.9 mm wide
Operating Temperature Range: -40°C to +85°C
بەراوردکردن لەگەڵ INA111AU →
Texas Instruments
Gain Range: 1 V/V to 10000 V/V (single external resistor)
Package: 8-pin SOIC (D)
Operating Temperature Range: -40 degC to +85 degC

INA111AUE4

✅ جێگرەوەی ڕاستەوخۆ
📦 16-pin PDSO
Same INA111 family and 16-pin format, but PDSO package drawing differs from INA111AU SOIC package; verify land pattern before replacement

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA111AP

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 16-pin PDSO
High-speed FET-input instrumentation amplifier · 1 circuit · Current-feedback instrumentation amplifier · 20 pA maximum · 500 µV maximum · 5 µV/°C maximum · 106 dB minimum · 2 MHz

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA114AU

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 16-pin SOIC
Single-amplifier precision instrumentation amplifier · 1 MHz · 11 nV/√Hz · 50 µV · 0.25 µV/°C · 2 nA · 115 dB · ±40 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA111AUG4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 16-pin SOIC
Instrumentation amplifier · 1 circuit · FET input · Current feedback · 2 MHz · 1 to over 1000 · 4 us to 0.01% at gain 100 · 1 external resistor

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA111AUPG4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-pin SOIC
Same INA111 family and 16-pin SOIC format, with a different ordering-grade suffix; confirm temperature grade and marking

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA111AU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type High-speed FET-input instrumentation amplifier
Number of Circuits 1 circuit
Bandwidth 2 MHz
Slew Rate 17 V/us
Input Bias Current 20 pA maximum
Input Offset Voltage 500 uV maximum
Input Offset Voltage Drift 5 uV/C maximum
Common-Mode Rejection Ratio 106 dB minimum
Gain Range 1 to 1000
Supply Voltage Range ±6 V to ±18 V
مەودای پلەی گەرمیی کارکردن -40 C to +85 C
پاکێج 16-pin SOIC (DW)
جۆری دامەزراندن Surface mount
Architecture Current-feedback instrumentation amplifier
Input Type FET input

ڕێنمایی ڕێکخستنی پینی INA111AU 16-pin soic (dw)

ڕێکخستنی پین بۆ INA111AU (پاکێجی 16-pin soic (dw)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 16-pin soic (dw) بۆ INA111AU

هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA111AU.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

INA111AU گونجاوە بۆ 6 بەکارھێنانs: Precision Bridge Transducer Amplification, Industrial Sensor Signal Conditioning, High-Impedance Current Measurement, Precision Data Acquisition Front End, Portable Measurement Equipment, Strain Gauge and Pressure Sensor Front Ends.

🏭

Precision Bridge Transducer Amplification

The INA111AU fits resistive bridge measurements where low-level differential signals must be amplified in the presence of substantial common-mode voltage. Its input bias current is specified at 20 pA maximum, helping minimize errors when the bridge and amplifier are connected through long or high-impedance lines. The 106 dB minimum common-mode rejection ratio improves rejection of excitation-related disturbances and supply noise. Set the gain with one external resistor according to the datasheet equation, and confirm that the bridge excitation, input common-mode range, and output swing remain within the device limits.

🔧

Industrial Sensor Signal Conditioning

For pressure, temperature, and position sensors, the INA111AU provides a combination of fast response and low input loading. The 2 MHz bandwidth supports signals that must be measured without excessive settling delay, while the 17 V/us slew rate allows the output to follow rapidly changing waveforms. The 500 uV maximum input offset voltage and 5 uV/C maximum drift establish important accuracy boundaries at the system level. Place the gain resistor and bypass capacitors close to the device, and evaluate the sensor’s source impedance before adding external input protection.

⚡

High-Impedance Current Measurement

The INA111AU is appropriate for current-shunt and current-transformer front ends where input bias current and common-mode performance influence measurement accuracy. A 20 pA maximum input bias current is especially useful when the shunt impedance is high or the source leakage current is significant. The 106 dB minimum common-mode rejection ratio helps preserve the differential signal when common-mode voltage changes. Confirm the allowable input common-mode voltage and output swing, and use guarded, short input routing to minimize leakage and surface contamination effects.

📟

Precision Data Acquisition Front End

INA111AU can condition fast, low-level differential inputs before an ADC or sampling system. Its 2 MHz bandwidth provides substantially more signal bandwidth than a slow precision instrumentation amplifier, while the 17 V/us slew rate helps preserve large or rapidly changing output transitions. Because usable bandwidth and settling performance depend on gain, derive the required gain and settling margin from the system timing budget. Add anti-alias filtering ahead of the amplifier or between stages, and use short, shielded routes for sensitive inputs.

📱

Portable Measurement Equipment

The low 20 pA maximum input bias current helps the INA111AU work with high-impedance electrodes, leakage-sensitive probes, and compact sensor modules. These systems benefit from a device that can amplify small differential signals while rejecting the common-mode voltage present on electrode leads. Portable applications must still account for supply voltage, power consumption, grounding, and electromagnetic coupling. Use a clean analog ground strategy, decouple the supply pins locally, and verify that the sensor’s output remains within the amplifier’s common-mode limits.

🖥️

Strain Gauge and Pressure Sensor Front Ends

The INA111AU suits strain-gauge bridges and resistive pressure elements where excitation produces a small differential output over a larger common-mode baseline. Its low input bias current limits the voltage error caused by finite source impedance, while its high minimum common-mode rejection improves signal integrity. The adjustable gain range from 1 to 1000 supports multiple bridge sensitivities. Select the gain resistor using the manufacturer equation, include the recommended bypass network, and verify bridge excitation voltage, common-mode range, and output headroom across temperature and load.

Where can I download the INA111AU datasheet PDF?
The official INA111AU datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina111.pdf. The manufacturer document describes the high-speed FET-input instrumentation amplifier, electrical characteristics, gain equation, package information, and typical application circuits. Use the 16-pin SOIC pin-description table when assigning PCB nets and designing the surrounding analog layout.
What are the key specifications of INA111AU that engineers should know?
The INA111AU combines a 2 MHz bandwidth, 17 V/us slew rate, input bias current of 20 pA maximum, input offset voltage of 500 uV maximum, and common-mode rejection of 106 dB minimum. According to the Texas Instruments INA111 datasheet, the device is a single-circuit FET-input instrumentation amplifier in a 16-pin SOIC package. Its externally programmed gain range is 1 to 1000.
What is the operating voltage range of INA111AU?
The INA111AU operates from ±6 V to ±18 V, allowing either regulated positive and negative supplies or suitable single-supply arrangements. The Texas Instruments INA111 datasheet specifies the electrical limits for these supply conditions. Confirm both the input common-mode range and output voltage swing at the intended supply and gain before using the amplifier.
Why should I choose INA111AU for a high-impedance sensor?
The INA111AU is appropriate when source impedance is high enough that input bias current could create a significant measurement error. Its FET input bias current is specified at 20 pA maximum, while the 106 dB minimum common-mode rejection ratio helps reject noise common to both sensor inputs. These characteristics support accurate differential measurements from resistive bridges and other high-impedance sources.
What is the INA111AU gain equation and how is gain set?
The INA111AU uses one external gain-setting resistor to establish the closed-loop gain, with a supported range of 1 to 1000. The exact resistor value depends on the selected gain and should be calculated from the gain equation in the Texas Instruments INA111 datasheet. Keep the resistor close to the gain pin and follow the datasheet’s recommended resistance range.
Where can I find the INA111AU pinout?
The INA111AU pinout is shown in the Texas Instruments INA111 datasheet package section. The device is available in the 16-pin SOIC DW package, so its footprint and land pattern differ from the 8-pin DIP version of the same amplifier family. Use the manufacturer pin-description table to identify supply, input, output, feedback, and gain-setting connections before PCB release.
How much bandwidth and slew rate does INA111AU provide?
The INA111AU provides 2 MHz bandwidth and a 17 V/us slew rate. According to the Texas Instruments INA111 datasheet, these high-speed figures are important for sensor systems that need rapid response rather than only minimum noise. Actual usable bandwidth depends on the programmed gain, load, output amplitude, and the required settling accuracy.
Is INA111AU suitable for bridge-transducer signal conditioning?
Yes, INA111AU is suitable for bridge-transducer signal conditioning because it combines differential input, low FET bias current, adjustable gain, and strong common-mode rejection. The 20 pA maximum input bias current limits loading of high-impedance bridge outputs, and the 106 dB minimum CMRR helps reject common-mode excitation and supply-related disturbances. The bridge excitation and input common-mode limits must still be checked.
What is the difference between INA111AU and INA111AUE4?
The INA111AUE4 is a same-family Texas Instruments variant offered in a 16-pin PDSO package, whereas INA111AU is specified in a 16-pin SOIC DW package. The comparison identifies the same high-speed instrumentation-amplifier functionality, including 2 MHz bandwidth and 17 V/us slew rate. Verify the exact package drawing, pin orientation, and temperature ordering before replacing one footprint with the other.
What is the best drop-in replacement for INA111AU?
INA111AUE4 is the closest documented same-family replacement candidate because it retains the INA111 architecture and 16-pin package format, but the package drawing must be checked before substitution. The cross-reference information also identifies INA111AP as another package variant of the same amplifier family. A replacement should not be selected solely by matching the pin count; confirm footprint, pinout, supply range, gain network, and temperature grade.
Can INA114AU replace INA111AU?
INA114AU should not be treated as an automatic drop-in replacement for INA111AU. The comparison describes INA114AU as a low-cost general-purpose instrumentation amplifier, while INA111AU is a high-speed FET-input device. Both are associated with 16-pin packages, but the gain network, electrical performance, and pin assignments must be verified directly before any board-level substitution.
When should I choose INA111AU over a general-purpose instrumentation amplifier?
Choose INA111AU when the measurement path needs high speed, very low input bias current, and strong common-mode rejection. Its 2 MHz bandwidth, 17 V/us slew rate, 20 pA maximum input bias current, and 106 dB minimum CMRR distinguish it from lower-cost general-purpose instrumentation amplifiers. Choose a general-purpose device instead when those speed and input-impedance benefits are not needed and cost is the primary constraint.
How do I minimize noise in an INA111AU circuit?
Use short input traces, place the gain-setting resistor close to the device, and bypass the supply pins with the capacitance recommended by the Texas Instruments INA111 datasheet. Avoid creating long high-impedance nodes between the sensor, input pins, and feedback components. For very small signals, pay particular attention to resistor thermal noise and source impedance, not only the amplifier’s offset specifications.
What compliance information is available for INA111AU?
The available manufacturer information identifies INA111AU as a RoHS-compliant instrumentation amplifier in the 16-pin SOIC DW package. The product documentation also states that the device is specified over -40 C to +85 C. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status should be confirmed from the manufacturer’s current product documentation or material declaration for the exact orderable MPN.
Where to buy INA111AU online and what is its current price?
Use the Request a Quote form on this page to request INA111AU pricing, availability, and lead time for your required quantity. The Request a Quote workflow is the appropriate channel for current commercial terms because pricing and stock can change without notice. Confirm the exact 16-pin SOIC suffix and package marking when submitting the request.
What is the lead time and stock status for INA111AU?
Current stock, minimum order quantity, and lead time for INA111AU should be requested through the Request a Quote form on this page. Provide the required quantity, shipment destination, and whether factory packing or another delivery format is needed. This gives procurement a complete request for the exact INA111AU orderable part instead of relying on a potentially stale inventory status.
Is INA111AU the same as INA111AP?
INA111AU and INA111AP are orderable variants of the same Texas Instruments INA111 instrumentation-amplifier family, but they use different 16-pin package drawings: SOIC DW for INA111AU and PDSO for INA111AP. Their shared family identity does not make them automatically interchangeable. Check the land pattern, pin numbering, exposed-pad requirements, and assembly requirements before substitution.

داتای سەرچاوەی ئەندازیاری بۆ INA111AU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose INA111AU when the design needs a fast, low-input-bias-current differential amplifier, particularly for high-impedance sensors, bridge measurements, and precision acquisition systems. Its 2 MHz bandwidth, 17 V/us slew rate, 20 pA maximum input bias current, and 106 dB minimum common-mode rejection provide a strong performance baseline. INA111AUE4 and INA111AP are same-family options for designs using a 16-pin PDSO footprint, subject to land-pattern and pinout verification. INA111AUG4 and INA111AUPG4 are same-family 16-pin SOIC ordering variants whose exact grade and marking must be confirmed. INA114AU is appropriate only when its lower-cost general-purpose feature set, gain implementation, and electrical ratings satisfy the design. For every replacement, verify the footprint, gain equation, common-mode range, output swing, supply voltage, and temperature grade before PCB release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA111AUE4 INA111AP INA114AU INA111AUG4 INA111AUPG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SOIC (DW) 16-pin PDSO 16-pin PDSO 16-pin SOIC 16-pin SOIC 16-pin SOIC
Product Type High-speed FET-input instrumentation amplifier High-speed FET-input instrumentation amplifier High-performance instrumentation amplifier General-purpose instrumentation amplifier INA111 family instrumentation amplifier INA111 family instrumentation amplifier

جیاکەرەوە سەرەکییەکان

  • High-speed signal conditioning (بەراورد بەINA114AU)
  • Very low input bias current (بەراورد بەINA111AUE4)
  • Differential gain control (بەراورد بەINA111AP)

تێبینییەکانی دیزاین

Route the two differential inputs as a compact, symmetric pair and keep the external gain-setting resistor close to the device. High-impedance input nodes should have minimal exposed copper and should not run beside switching nodes or digital clocks. Place the recommended bypass capacitors at the supply pins with short ground returns so that supply noise is rejected before it reaches the amplifier.

Check the input common-mode range, output swing, and gain-dependent bandwidth against the worst-case operating condition. The 2 MHz bandwidth and 17 V/us slew rate describe high-speed capability, but they do not guarantee useful accuracy above the gain and settling requirements of the downstream converter. Add input filtering only where the filter impedance remains low enough not to create excessive bias-current error.

Do not substitute solely by amplifier type or pin count. INA111-family alternatives may use different SOIC and PDSO package drawings, while INA114AU has a different gain-setting implementation. Confirm pin numbering, land pattern, gain resistor value, feedback connections, supply limits, and temperature grade against each candidate’s manufacturer datasheet before approving a replacement.

Connect analog and digital return currents carefully, especially when the INA111AU is placed near an ADC, switching regulator, or communications interface. Keep the bypass loop short, use a continuous analog ground reference, and route high-current outputs away from the input pair. Grounding and shielding techniques should be evaluated together because aggressive splitting can create additional ground potential differences in low-level measurements.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer product information identifies the INA111 family as RoHS compliant. REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification details were not established for the exact orderable MPN.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ina111au datasheet INA111AU datasheet pdf INA111AU pinout INA111AU specifications Texas Instruments INA111AU INA111AU 16-SOIC INA111AU gain equation INA111AU application circuit INA111AU drop-in replacement INA111AU equivalent INA111AU vs INA114AU INA111AU price INA111AU stock INA111AU high impedance sensor

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA111AU INA111AUE4 INA111AP INA114AU INA111AUG4 INA111AUPG4 instrumentation amplifier differential amplifier FET-input amplifier current-feedback architecture semiconductor input bias current common-mode rejection ratio offset voltage drift gain-setting resistor 16-pin SOIC SOIC family surface-mount package SMD package bridge transducer precision data acquisition industrial sensor conditioning RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ