Texas Instruments

INA114BP - 1MHz Precision Instrumentation Amplifier | TI

MPN: INA114BP ✓ چالاک
50 uV maximum Vdss 2 nA maximum Id 8-pin PDIP Package
MOQ: 1 |

INA114BP گشتی

Texas Instruments INA114BP is a precision three-op-amp instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV maximum offset voltage, and an 8-pin PDIP package. It supports gains from 1 to 10,000 through one external gain-setting resistor, while input protection tolerates voltages up to +/-40 V. Its low-noise and high-accuracy characteristics make it suitable for measuring small differential signals in industrial, medical, and test systems.

An instrumentation amplifier is a specialized amplifier category designed to extract a small differential voltage while rejecting common-mode interference. Its internal three-op-amp architecture provides high input impedance and precise gain control, making it more effective than ordinary operational amplifiers in many sensor-front-end applications. Within the signal-chain hierarchy, it belongs to the broader family of amplifier ICs and analog signal-conditioning components.

Key features include 11 nV/sqrt(Hz) input noise, 115 dB minimum common-mode rejection, 2 nA maximum input bias current, and 0.25 uV/degree C maximum input offset drift. The low offset voltage and drift reduce measurement errors in bridge, strain-gauge, and low-level current sensing systems. Internal input protection supports +/-40 V, helping the device tolerate transient overloads encountered outside the normal operating input range.

The INA114 uses a versatile three-op-amp signal chain and accepts single or dual supply operation. Its gain is established with one external resistor, allowing a single circuit implementation to cover gain settings from 1 to 10,000. The 1 MHz bandwidth supports dynamic sensor signals while remaining appropriate for precision industrial instrumentation rather than very high-frequency signal extraction.

Typical uses include 4-20 mA current-loop receivers, strain-gauge bridge amplifiers, isolated-signal front ends, precision current-shunt measurements, biomedical instrumentation, and laboratory measurement equipment. The device is particularly useful when the wanted differential signal is small relative to ground offsets or common-mode noise present at the input connectors.

When designing the input stage, use an external gain resistor with suitable stability and thermal characteristics, keep input traces short, and connect the reference pin to a clean analog ground when unity gain is required. Check input common-mode range and output swing at every supply voltage before selecting the final gain, because bandwidth and output capability change with operating conditions.

This page combines the device's precision specifications, application guidance, package information, replacement analysis, and practical design considerations to support faster component evaluation and more reliable front-end design.

جێگرەوەکانی جێگۆڕکێ بۆ INA114BP — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA114BP (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Common-Mode Rejection Ratio, Gain Range, Input Bias Current.

Texas Instruments
Common-Mode Rejection Ratio: 106 dB minimum
Gain Range: 1 to greater than 1000
Input Bias Current: 20 pA maximum
بەراوردکردن لەگەڵ INA114BP →

INA114BPG4

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Same INA114 instrumentation-amplifier family and 8-pin DIP outline; the available comparison does not quantify suffix-specific electrical differences.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

INA114AP

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
Precision instrumentation amplifier · 1 circuit · 1 MHz · 50 µV · 0.25 µV/°C · 11 nV/√Hz · 2 nA · 115 dB

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA111BP

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
1 circuit · High-speed FET-input instrumentation amplifier · 8-pin PDIP · Through-hole · 20 pA maximum · 500 uV maximum · 5 uV/°C maximum · 106 dB minimum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA114BP زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Precision instrumentation amplifier
Number of Amplifiers 1 circuit
Architecture Three-op-amp instrumentation amplifier
Gain Range 1 to 10,000
Gain-Bandwidth Product 1 MHz
Input Noise 11 nV/sqrt(Hz)
Input Offset Voltage 50 uV maximum
Input Offset Drift 0.25 uV/degree C maximum
Input Bias Current 2 nA maximum
Common-Mode Rejection Ratio 115 dB minimum
Input Overvoltage Protection +/-40 V
ڤۆڵتیەی دابینکردن +/-18 V maximum
ئێستای ئارام 3 mA maximum
مەودای پلەی گەرمیی کارکردن -40 degrees C to +85 degrees C
پاکێج 8-pin PDIP
جۆری دامەزراندن Through-hole
Gain Configuration Single external resistor

ڕێنمایی ڕێکخستنی پینی INA114BP 8-pin pdip

ڕێکخستنی پین بۆ INA114BP (پاکێجی 8-pin pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pin pdip بۆ INA114BP

هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA114BP.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

INA114BP گونجاوە بۆ 6 بەکارھێنانs: Precision Current-Shunt Measurement, Strain-Gauge Bridge Instrumentation, 4-20 mA Process-Control Receiver, Medical and Biomedical Signal Conditioning, Portable Sensor and IoT Interface, Precision Test and Measurement Front End.

⚡

Precision Current-Shunt Measurement

The INA114BP suits low-side current measurement when a small differential voltage across a shunt must be amplified in the presence of a much larger common-mode voltage. Its 115 dB minimum common-mode rejection reduces errors from supply and ground disturbances, while 2 nA maximum input bias current limits disturbance of the shunt network. A gain from 1 to 10,000 is available through one external resistor. Choose the gain so the expected load current produces useful output swing without clipping, and keep the shunt connections short to minimize added pickup. The 1 MHz bandwidth accommodates rapidly changing current, while the 50 uV maximum offset sets an important floor for low-current measurements.

🏭

Strain-Gauge Bridge Instrumentation

The INA114BP is appropriate for resistive strain-gauge bridges where the full-scale differential signal is small and the bridge midpoint can sit at a substantial common-mode voltage. Its 11 nV/sqrt(Hz) input noise and 0.25 uV/degree C maximum offset drift help preserve the integrity of millivolt-level measurements. The 1 to 10,000 gain range allows one amplifier topology to cover different bridge sensitivities. Use regulated bridge excitation, verify the input common-mode range under worst-case imbalance, and place the amplifier close to the bridge to avoid adding noise between the sensor and input pins.

🏭

4-20 mA Process-Control Receiver

The INA114BP can amplify the differential voltage produced by a 4-20 mA industrial transmitter while rejecting the common-mode voltage present on long field-wired loops. Its 115 dB minimum common-mode rejection and input protection to +/-40 V add useful robustness for industrial interfaces, although the normal operating range must still be respected. The external gain resistor lets the receiver establish the required scale factor and bandwidth without a complex resistor network. Place surge-protection components at the connector, keep their capacitance and leakage under control, and confirm that the selected gain remains compatible with the transmitter output at zero and full-scale current.

💊

Medical and Biomedical Signal Conditioning

The INA114BP provides the differential input stage required for low-level biomedical transducers when the source includes large electrode or supply common-mode offsets. Its low input bias current of 2 nA maximum and 50 uV maximum offset voltage are useful for high-impedance sensor interfaces, while 11 nV/sqrt(Hz) input noise supports sensitive signal conditioning. The instrument-amplifier architecture reduces dependence on resistor matching in the input stage. In patient-connected equipment, however, system safety, isolation, leakage, and applicable regulatory requirements must be evaluated independently; the amplifier itself is not a complete medical interface solution.

🧩

Portable Sensor and IoT Interface

The INA114BP is useful in compact sensor interfaces that amplify a small differential output while rejecting battery-system noise and ground offsets. The 3 mA maximum quiescent current supports power-conscious instrumentation, and the 8-pin PDIP package simplifies through-hole prototyping and repair. A gain from 1 to 10,000 lets the same amplifier family serve resistive, magnetic, and current-sensing front ends. Because it is a through-hole package rather than a miniature surface-mount option, compare board area carefully against newer surface-mount instrumentation amplifiers. Confirm low-voltage common-mode range, output swing, noise, and overall standby current before finalizing a wearable or compact IoT design.

🔧

Precision Test and Measurement Front End

The INA114BP supports laboratory and production-test front ends that must resolve small differential signals with limited common-mode interference. Its 1 MHz bandwidth, 115 dB minimum common-mode rejection, and selectable gain are useful for conditioning bridge outputs, precision dividers, and diagnostic loops. The 50 uV maximum offset and 0.25 uV/degree C maximum drift establish important calibration limits, so system-level error budgets should include resistor tolerance, reference accuracy, and temperature. Use short guarded input traces, clean grounding, and an output ADC whose noise and input range complement the amplifier rather than limiting system accuracy.

What are the key specifications of INA114BP that engineers should know?
The INA114BP is a precision instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV maximum input offset voltage, 11 nV/sqrt(Hz) input noise, and programmable gain from 1 to 10,000. According to the Texas Instruments datasheet, it also provides 115 dB minimum common-mode rejection, 2 nA maximum input bias current, and input protection up to +/-40 V. The device is supplied in an 8-pin PDIP package for through-hole PCB assembly.
Where can I download the INA114BP datasheet PDF?
The official INA114BP datasheet and product documentation are available through the Texas Instruments product page for INA114 and the TI document link. According to Texas Instruments, the INA114 family is offered in 8-pin PDIP and 16-pin SOIC packages. Use the manufacturer's ordering table to confirm that INA114BP corresponds to the 8-pin PDIP ordering option before releasing a production BOM.
Where can I find the INA114BP pinout?
Use the pin-configuration and package drawings in the Texas Instruments INA114 datasheet to identify the INA114BP connections. The BP ordering option is an 8-pin PDIP package, while the same-family SOIC option uses a different package outline. Before PCB routing, verify the exposed lead positions and orientation against the manufacturer's drawing rather than relying solely on a third-party pinout image.
What is the INA114BP used for?
The INA114BP is used to amplify low-level differential sensor signals while rejecting common-mode interference. According to the Texas Instruments datasheet, its 1 to 10,000 gain range, 115 dB minimum common-mode rejection, and 50 uV maximum offset voltage suit bridge sensors, strain gauges, current-shunt monitors, and 4-20 mA receiver circuits. Its +/-40 V input protection is also useful in industrial interfaces exposed to electrical transients.
What is the gain range of INA114BP and how is gain set?
The INA114BP supports gain settings from 1 to 10,000, and one external resistor sets the gain. According to the Texas Instruments datasheet, this resistor also permits useful combinations of gain and bandwidth for a given operating point. Choose a resistor with low temperature coefficient and adequate noise performance when precision offset behavior is more important than the lowest possible component cost.
What is the input noise and offset voltage of INA114BP?
The INA114BP has input noise of 11 nV/sqrt(Hz) and input offset voltage of 50 uV maximum. According to the Texas Instruments datasheet, its maximum input offset drift is 0.25 uV/degree C. These figures make the device appropriate for bridge transducers and precision current measurements where amplifier error must remain small relative to the sensed signal.
Can INA114BP accept inputs up to 40 volts?
The INA114BP includes internal input protection that can withstand inputs up to +/-40 V without damage. According to the Texas Instruments datasheet, the normal operating input range remains a separate design constraint. Input protection improves fault tolerance, but it does not permit operation outside the specified common-mode range or justify continuous operation at the maximum withstand voltage.
What supply voltage should be used with INA114BP?
The INA114BP supports single or dual supply operation, with a maximum stated supply of +/-18 V. According to the Texas Instruments datasheet, the permissible input common-mode range and output swing depend on the selected supply voltage. Design the power rails so the sensor nodes and regulated output remain inside those limits at startup, overload, and minimum-load conditions.
How does INA114BP compare with INA111BP?
Both INA114BP and INA111BP are 8-pin DIP instrumentation amplifiers, but their gain and performance details differ. The INA114BP supports gain from 1 to 10,000, has 1 MHz bandwidth, 50 uV maximum offset voltage, and +/-40 V input protection. According to the Texas Instruments product documentation, the INA114 uses one external resistor for gain setting. Confirm the complete INA111 electrical limits before exchanging the devices.
What is the difference between INA114BP and INA114BPG4?
INA114BP and INA114BPG4 are both identified as 8-pin DIP instrumentation amplifiers and appear in a direct product comparison. The available comparison information does not establish whether their temperature grade, marking, or qualification differs. According to the Texas Instruments ordering information for INA114, engineers should match the exact orderable suffix and verify all electrical and environmental requirements before treating them as interchangeable.
When should I choose INA114BP over an ordinary operational amplifier?
Choose INA114BP when the source is a low-level differential sensor and common-mode rejection, high input impedance, and simple gain setting are important. An ordinary operational amplifier may require several resistors and additional input-stage design to achieve comparable behavior. The INA114BP provides 115 dB minimum common-mode rejection, 2 nA maximum input bias current, and gain from 1 to 10,000 in one integrated circuit.
Is INA114BP suitable for strain-gauge bridge measurement?
The INA114BP is suitable for strain-gauge bridge measurements because it combines differential input, high common-mode rejection, and selectable gain in one package. According to the Texas Instruments datasheet, its 50 uV maximum offset voltage and 0.25 uV/degree C maximum drift support stable low-level measurements. The bridge excitation supply should still be regulated, and the final error budget must include excitation drift and resistor tolerance.
What can replace INA114BP as a drop-in part?
INA114BPG4, INA114AP, and INA111BP are the closest documented candidates for a replacement review, but each still requires an exact pin, gain, and electrical verification. The cross-reference material identifies INA114BPG4 as an 8-DIP instrumentation amplifier and provides direct comparisons with INA114AP and INA111BP. Use the Request a Quote form on this page to discuss the exact suffix and sourcing requirements with the supply team.
Is there an Analog Devices equivalent for INA114BP?
Cross-reference sources identify Analog Devices among manufacturers associated with INA114 alternatives, but the available cross-reference excerpt does not name a specific Analog Devices MPN or confirm its package and pinout. A valid drop-in replacement must use the same 8-pin PDIP footprint and preserve the gain-setting, reference, supply, and input-protection functions. Use the manufacturer's cross-reference tool and the INA114 datasheet to confirm any proposed substitute before schematic or PCB changes.
Where to buy INA114BP, what is the price, and what is the lead time?
The INA114BP can be requested through the Request a Quote form on this page, which is the appropriate route for current price, stock, and lead-time confirmation. According to the Texas Instruments product page, the INA114 family is available in 8-pin PDIP and 16-pin SOIC packages, while the INA114BP ordering option corresponds to the PDIP version. The request should state the required quantity, reel or tube preference, and target delivery date.

داتای سەرچاوەی ئەندازیاری بۆ INA114BP — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose INA114BP when the design needs a through-hole, three-op-amp instrumentation amplifier with gain from 1 to 10,000, 115 dB minimum common-mode rejection, 50 uV maximum offset, and input protection up to +/-40 V. It is particularly suitable for bridges, current shunts, and industrial differential sensors whose signals are small relative to common-mode voltage. Review INA114BPG4 first when an alternate Texas Instruments ordering code may satisfy the same footprint, but verify its exact electrical and qualification details. Consider INA114AP only after confirming suffix-specific offset, drift, gain, and environmental requirements. INA111BP is a closer architectural candidate, but its different gain range and electrical limits make it less suitable when the full 1 to 10,000 range or INA114 precision characteristics are required. For a new surface-mount design, compare the INA114's PDIP size against smaller instrumentation amplifiers before committing to this through-hole package.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA114BPG4 INA114AP INA111BP
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Product Type Precision instrumentation amplifier Instrumentation amplifier Precision instrumentation amplifier Instrumentation amplifier

جیاکەرەوە سەرەکییەکان

  • Wide programmable gain with one external resistor (بەراورد بەINA111BP)
  • Documented precision offset and drift (بەراورد بەINA114AP)
  • High common-mode rejection for differential sensing (بەراورد بەINA114BPG4)

تێبینییەکانی دیزاین

Route the differential input pair as a short, symmetric pair and keep them away from switching nodes and high-current return paths. Connect the gain-setting resistor directly to the appropriate pins, and place any input protection components close to the connector. Since the device specifies 11 nV/sqrt(Hz) input noise, unnecessary copper, breadboard wiring, and leakage can materially degrade the noise performance of a millivolt-level measurement.

Check the common-mode input range, output swing, and gain at the lowest operating supply voltage rather than checking only the nominal rail. The device supports single and dual supplies and has a stated maximum of +/-18 V. Use a supply arrangement that keeps every input node inside its common-mode range, including during startup and sensor-signal transitions. Bypass the supply pins locally with the capacitance recommended by the manufacturer datasheet.

Do not treat the +/-40 V input-protection rating as the normal operating input range. Protection helps against fault conditions, but excessive voltage can still produce unintended current, heating, or saturation. Also avoid assuming that identical package outlines guarantee a replacement: verify gain-resistor equations, reference-pin behavior, input limits, offset, noise, and common-mode rejection for the exact alternative ordering code.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No explicit component compliance declarations were identified. Use the current Texas Instruments product and material-compliance documentation for production qualification.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ina114bp datasheet INA114BP precision instrumentation amplifier INA114BP pinout INA114BP datasheet pdf INA114BP 1MHz INA114BP 50uV offset INA114BP 8-pin PDIP INA114BP equivalent INA114BP replacement INA114BP vs INA111BP INA114BP gain resistor INA114BP current shunt amplifier INA114BP price INA114BP stock Texas Instruments INA114BP

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA114BP INA114BPG4 INA114AP INA111BP precision instrumentation amplifier three-op-amp architecture amplifier IC analog signal conditioning differential input common-mode rejection ratio CMRR gain-bandwidth product input offset voltage input offset drift input bias current input noise overvoltage protection quiescent current single external gain resistor 8-pin PDIP DIP package through-hole mounting strain-gauge bridge 4-20 mA current loop
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ