INA114BU - 1MHz Precision Instrumentation Amplifier | TI
MPN: INA114BU ✓ چالاکINA114BU گشتی
An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals superimposed on large common-mode voltages. It belongs to the amplifier hierarchy as an instrumentation amplifier, differential amplifier, and analog signal-conditioning IC. Its internal three-op-amp architecture improves common-mode rejection and enables gains from 1 to 10,000 by selecting one external gain-setting resistor. This makes the INA114BU useful when a sensor, transducer, or measurement bridge produces a low-level differential output that must be amplified without amplifying system noise or supply variation equally.
The most prominent INA114BU characteristics are its 1 MHz bandwidth, 50 uV offset voltage, and 11 nV/√Hz noise density. The single external gain resistor simplifies adjustment while preserving a broad usable gain range. Input protection can withstand voltages to ±40 V, helping the amplifier tolerate moderate overvoltage conditions. A 2.25 V to 18 V supply range supports both low-voltage and conventional industrial analog systems, while the approximately 3 mA supply-current figure supports low-power instrumentation.
The INA114BU uses a versatile three-op-amp instrumentation-amplifier architecture. Its gain is established by the external resistor connected to the gain-setting node, avoiding the need for matched resistor networks. Input and feedback resistors are integrated internally, while the specified input-noise and offset characteristics support accurate extraction of small differential signals. The 1 MHz bandwidth allows the amplifier to process signals beyond static or very-low-frequency measurement tasks while retaining a compact analog implementation.
Typical uses include bridge-based pressure and load sensing, biomedical instrumentation, current-shunt measurement, laboratory test equipment, and industrial process-control front ends. The 16-pin SOIC package is useful where moderate pin count, surface-mount assembly, and access to a conventional package are preferred. Its ±40 V input-protection capability is especially relevant when a sensor line can experience transient or sustained voltage excursions.
Circuit design should begin with the required gain and bandwidth. Because gain is set by one resistor, verify its noise contribution, tolerance, and stability alongside the sensor source impedance. Keep input and feedback routing short, use a clean low-noise ground reference, and place supply-bypass capacitance close to the device. Check the ±40 V protection rating against the actual maximum input voltage rather than treating it as a substitute for normal operation within the supply range.
This product page combines the Texas Instruments INA114 specifications with package information, practical application guidance, drop-in comparison candidates, and design considerations. The comparisons focus on same-package precision instrumentation amplifiers, while the application guidance focuses on practical gain selection, input protection, noise, and layout considerations for measurement circuits.
جێگرەوەکانی جێگۆڕکێ بۆ INA114BU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA114BU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate, Supply Voltage Range, Product Type, Amplifier Type.
INA111BU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA115BU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA116UAG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA114BU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Precision instrumentation amplifier |
| Architecture | Three-op-amp design |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 50 uV |
| Input Noise Density | 11 nV/√Hz |
| Typical Supply Current | 3 mA |
| Gain Range | 1 to 10,000 |
| Gain-Setting Method | One external resistor |
| Supply Voltage Range | 2.25 V to 18 V |
| Input Protection Range | ±40 V |
| Slew Rate | 0.06 V/µs |
| Settling Time | 600 ns |
| مەودای پلەی گەرمیی کارکردن | -40°C to +85°C |
| پاکێج | 16-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Product Type | Low-cost, general-purpose precision instrumentation amplifier |
ڕێنمایی ڕێکخستنی پینی INA114BU 16-pin soic
ڕێکخستنی پین بۆ INA114BU (پاکێجی 16-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA114BU.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
INA114BU گونجاوە بۆ 6 بەکارھێنانs: Bridge-Based Sensor Measurement, Medical and Biomedical Instrumentation, Industrial Process and Pressure Control, Current-Shunt Measurement, Laboratory Test and Measurement, Data Acquisition and Analog Sensing.
Bridge-Based Sensor Measurement
The INA114BU is well suited to bridge excitation and differential sensor measurement because its three-op-amp architecture provides high common-mode rejection and programmable gain from 1 to 10,000. According to the Texas Instruments INA114 datasheet, the device combines a 1 MHz gain-bandwidth product with 50 uV input-offset voltage and 11 nV/√Hz input noise. Place it directly after the bridge output to amplify the small differential voltage without amplifying the larger common-mode voltage. The principal trade-off is bandwidth: gain must remain low enough for the required signal bandwidth, so the gain-setting resistor cannot be selected solely from the bridge sensitivity.
پێشنیارکراو
Medical and Biomedical Instrumentation
The INA114BU can amplify low-level physiological and diagnostic signals when the circuit requires differential input, adjustable gain, and a compact surface-mount implementation. Its 11 nV/√Hz input noise and 50 uV input-offset voltage are useful for preserving small sensor outputs, while the 1 MHz bandwidth supports signals beyond static measurements. According to the Texas Instruments INA114 datasheet, the gain is programmed with one external resistor from 1 to 10,000. Medical designs must still evaluate patient protection, isolation, leakage, electrode protection, and applicable safety requirements independently of the amplifier specifications.
پێشنیارکراو
Industrial Process and Pressure Control
The INA114BU fits industrial pressure, strain, and process-sensing front ends where a transducer produces a small differential signal over a substantial common-mode range. The precision three-op-amp architecture, selectable gain from 1 to 10,000, and 1 MHz gain-bandwidth product provide a practical balance between resolution and signal speed. According to the Texas Instruments INA114 datasheet, the amplifier can also tolerate input voltages to ±40 V. That protection capability helps manage moderate industrial transients, but it does not replace surge protection, fusing, or correctly rated field wiring.
پێشنیارکراو
Current-Shunt Measurement
The INA114BU is suitable for measuring the small voltage developed across a current-shunt resistor when the amplifier must reject supply-related common-mode voltage. Its 1 MHz gain-bandwidth product allows measurement of higher-bandwidth current events than a slow precision-only amplifier, while 11 nV/√Hz input noise supports sensitive shunt ranges. According to the Texas Instruments INA114 datasheet, a single resistor establishes gains from 1 to 10,000. Designers should account for Kelvin connections, shunt resistance and tolerance, amplifier offset, and the thermal behavior of the current-sense element.
پێشنیارکراو
Laboratory Test and Measurement
The INA114BU works as a precision front end for laboratory instruments that amplify low-level differential signals before conversion or analysis. Its 50 uV input-offset voltage and 11 nV/√Hz input noise support accurate measurement, while the 1 MHz bandwidth is useful for waveform and transient systems. According to the Texas Instruments INA114 datasheet, the 16-pin SOIC package supports compact instrument designs and gains from 1 to 10,000. For highest bench accuracy, calibrate offset and gain error, use a low-noise gain resistor, provide stable supply bypassing, and avoid long unprotected input routes.
پێشنیارکراو
Data Acquisition and Analog Sensing
The INA114BU can condition differential outputs from sensors and analog measurement systems before they reach an ADC. Its programmable gain from 1 to 10,000 allows the amplifier to scale sensor outputs into a useful input range, while the 1 MHz gain-bandwidth product is appropriate for many moderate-speed acquisition systems. According to the Texas Instruments INA114 datasheet, the device operates from 2.25 V to 18 V and typically consumes 3 mA. Select the gain and external resistor together so that noise, settling time, ADC input range, and anti-alias filtering remain compatible.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ INA114BU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | INA111BU | INA115BU | INA116UAG4 |
|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Precision instrumentation amplifier | Instrumentation amplifier | Precision instrumentation amplifier | Precision instrumentation amplifier |
جیاکەرەوە سەرەکییەکان
- Single-resistor gain programming across a broad range (بەراورد بەINA111BU)
- Documented 1 MHz gain-bandwidth performance (بەراورد بەINA115BU)
- Precision offset and noise specifications (بەراورد بەINA116UAG4)
- Dedicated input protection capability (بەراورد بەINA111BU)
تێبینییەکانی دیزاین
Do not select the gain-setting resistor from the required gain alone. The INA114BU supports gains from 1 to 10,000, but its 1 MHz gain-bandwidth product must also satisfy the measurement bandwidth. Estimate the maximum operating frequency and compare it with the bandwidth available at the selected gain. Also include gain-resistor tolerance and temperature coefficient in the output-error budget.
Keep the input, gain-setting, feedback, and output routes short to minimize parasitic capacitance and susceptibility to interference. Place input-referenced decoupling and biasing components near the device rather than near the sensor or ADC. Use a continuous ground reference with minimal loop area, and avoid routing sensitive input traces parallel to switching-node or high-current power traces.
The ±40 V input-protection rating should not be treated as a substitute for normal operation within the specified electrical limits. Confirm that the maximum possible input voltage, including transients and fault conditions, remains compatible with the complete signal path. Add external attenuation, clamping, or surge protection when the sensor line can exceed the limits associated with the application.
Place supply-bypass capacitance immediately across the power and ground pins, with the return path short and close to the device. The INA114BU typically consumes 3 mA, but supply noise can still modulate the measured signal through finite power-supply rejection. Keep the regulator capable of the required transient current and avoid sharing long supply traces with noisy switching loads.
زانیاری پابەندبوون
The device is specified for -40°C to +85°C operation, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the referenced product information.