ISL8485EIP - 5V RS-485/RS-422 Transceiver | Renesas
MPN: ISL8485EIP ✓ چالاکISL8485EIP گشتی
An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential balanced signals. RS-485 supports longer multipoint buses and common-mode noise tolerance, while RS-422 favors point-to-point, full-duplex communication. The ISL8485EIP belongs to the transceiver hierarchy: interface transceiver → differential line driver and receiver → communications interface IC.
The principal benefits of the ISL8485EIP are its ±15 kV ESD protection, 4.5 V to 5.5 V supply tolerance, low-power BiCMOS implementation, and selectable high-speed or slew-rate-limited operation. Driver short-circuit current limiting and on-chip thermal shutdown improve robustness during bus contention. These characteristics suit equipment connected to industrial wiring where electrostatic discharge and ground-potential differences are common.
The device supports both RS-485 and RS-422 balanced communication. Its driver outputs and receiver inputs are protected against ESD events, while the receiver can provide a fail-safe output when the bus is idle. The device operates from a single 5 V rail, allowing integration with conventional 5 V control logic. Exact propagation-delay, receiver-threshold, and load-current limits should be confirmed against the manufacturer datasheet before release.
Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, data acquisition, and communications interfaces that require protection from cable-borne electrostatic discharge. The device is particularly useful where a 5 Mbps bus must tolerate electrical transients at exposed connector pins. PCB layout still requires a controlled return path and careful connection of the external interface network.
Place protection and termination components close to the transceiver pins, route the differential pair as a tightly coupled pair, and provide a low-impedance ground reference. Respect the datasheet limits for driver load, receiver input, and supply bypassing. Keep analog and digital return currents separated where possible to reduce common-mode conversion and improve signal integrity.
This page combines the manufacturer interface description, package information, sourcing data, and practical design guidance to support component selection. It also distinguishes the pin-compatible family alternatives from functionally similar devices that may require different package or operating details, helping engineers narrow a replacement without assuming interchangeability.
جێگرەوەکانی جێگۆڕکێ بۆ ISL8485EIP — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ISL8485EIP (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە ESD Protection, Product Type, Supply Voltage Range.
ISL8483EIP
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →ISL8485EIPZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SP485EEP-L
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX485EEPA+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ISL8485EIP تایبەتمەندییەکان
| Product Type | Single RS-485/RS-422 transceiver |
| Number of Transceivers | 1 transceiver |
| Communications Modes | RS-485 and RS-422 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 5 Mbps |
| Driver and Receiver Count | 1 driver and 1 receiver |
| Driver Output Protection | Short-circuit current limiting |
| Thermal Protection | On-chip thermal shutdown |
| ESD Protection | ±15 kV on each driver output and receiver input |
| ESD Latch-up Protection | Yes |
| Process Technology | BiCMOS |
| پاکێج | 8-pin PDIP |
| جۆری دامەزراندن | Through-hole |
| دۆخی RoHS | Compliant |
ڕێنمایی ڕێکخستنی پینی ISL8485EIP 8-pin pdip
ڕێکخستنی پین بۆ ISL8485EIP (پاکێجی 8-pin pdip). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ISL8485EIP.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ISL8485EIP گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Networks, Building and HVAC Automation, Instrumentation and Data Acquisition, Security and Surveillance Systems, Industrial Sensor and Actuator Backplanes, Communication Port Cards and Gateways.
Industrial RS-485 Control Networks
The ISL8485EIP fits industrial RS-485 control networks that connect remote sensors, actuators, programmable controllers, and motor-drive modules over a shared differential bus. Its 5 Mbps maximum data rate supports high-bandwidth factory data paths, while the 4.5 V to 5.5 V supply range accommodates conventional 5 V industrial logic. The ±15 kV ESD protection on each driver output and receiver input improves robustness at factory wiring boundaries. Bus contention is addressed by driver short-circuit current limiting and thermal shutdown. Designers should still preserve controlled return paths, minimize cable stubs, and verify termination and fail-safe behavior for the selected network topology.
پێشنیارکراو
Building and HVAC Automation
The ISL8485EIP can connect thermostats, variable-air-volume controllers, room sensors, and supervisory controllers in building and HVAC automation systems. RS-485 differential signaling helps maintain data integrity across long cables and environments containing switching loads. The transceiver's 5 V operation suits embedded controls that already regulate their logic rail, while ±15 kV ESD protection adds robustness where field wiring enters an enclosure. Its short-circuit limiting and thermal shutdown protect the interface during inactive, miswired, or contended bus conditions. Confirm the receiver thresholds and idle-state behavior against the automation network specification before commissioning the controller board.
پێشنیارکراو
Instrumentation and Data Acquisition
The ISL8485EIP is appropriate for instrumentation links carrying commands and measurements between a data-acquisition controller and remote front-end equipment. The 5 Mbps rate supports the data throughput of compact measurement systems, while thebalanced differential interface reduces susceptibility to common-mode noise found near motors and power converters. Integrated ESD protection helps protect the controller from electrostatic discharge introduced through measurement cables. Use the receiver in the correct enabled state during bus idle, provide a solid analog and digital ground strategy, and follow the manufacturer component placement and external-network recommendations to preserve signal integrity.
پێشنیارکراو
Security and Surveillance Systems
The ISL8485EIP can interface control panels, access-control readers, intercom stations, and distributed camera-control modules using RS-485. The device supports communication rates up to 5 Mbps, allowing short-distance command and status links to operate with low protocol overhead. Its ±15 kV ESD protection is particularly relevant for cabinet and outdoor wiring interfaces exposed to human contact or nearby charged objects. Short-circuit current limiting and thermal shutdown improve resilience during bus contention. The circuit should still include connector grounding, controlled cable routing, and the correct termination network to avoid reflections and excessive common-mode conversion.
پێشنیارکراو
Industrial Sensor and Actuator Backplanes
The ISL8485EIP supports compact backplanes that connect distributed sensors, relay outputs, valve controllers, and motor-control modules. A 5 Mbps bus rate allows command traffic and status feedback to share the same balanced wiring when the network protocol permits. Because industrial backplanes may be exposed to plug-in cards and differing ground potentials, the transceiver's ±15 kV ESD protection, current-limited driver, and thermal shutdown add useful robustness. Validate the total bus length, node count, termination, and cable-stub geometry so that reflections do not reduce receiver margins.
پێشنیارکراو
Communication Port Cards and Gateways
The ISL8485EIP is useful in communication port cards, serial gateways, and legacy-equipment adapters that need an RS-485/RS-422 interface. Its 8-pin PDIP package supports through-hole assembly and straightforward prototyping, while the single transceiver architecture allows one port to handle a half-duplex RS-485 bus or a directional RS-422 connection. The ±15 kV bus-pin ESD protection is valuable when the port connects to external equipment. During design-in, verify enable polarity, receiver fail-safe behavior, propagation timing, and loading against the host UART and protocol timing to prevent framing errors.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ISL8485EIP — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ISL8483EIP | ISL8485EIPZ | SP485EEP | MAX485EEPA |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Maxim Integrated | Maxim Integrated |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Transceiver Count | 1 | 1 | 1 | 1 | 1 |
جیاکەرەوە سەرەکییەکان
- Specified ESD resilience on all exposed bus pins (بەراورد بەMAX485EEPA)
- Wide 5 V supply tolerance (بەراورد بەSP485EEP)
- High-speed capability with configurable communication behavior (بەراورد بەISL8483EIP)
- Protected driver under bus contention (بەراورد بەSP485EEP)
تێبینییەکانی دیزاین
Place the transceiver, supply bypass capacitor, and any termination or bias network close to their associated pins. Keep the RS-485/RS-422 driver and receiver traces as a tightly coupled differential pair with a continuous ground reference. Avoid routing the pair through switching-power regions or splitting it across unrelated copper zones, because those practices increase common-mode conversion and can reduce receiver margin.
Do not approve a substitute from package shape alone. Compare the original and candidate for driver-enable polarity, receiver-enable behavior, receiver thresholds, fail-safe state, propagation delay, maximum data rate, supply tolerance, and ESD rating. The ISL8485EIP also provides driver current limiting and thermal shutdown, so a candidate lacking equivalent protection may be unsuitable for exposed industrial wiring even if its pin arrangement matches.
Use the manufacturer pin-description and application-circuit information when assigning the PDIP-8 nets. In particular, verify the driver-enable and receiver-enable controls before connecting a UART because incorrect logic states can hold the bus in an active condition and prevent other nodes from communicating. Confirm the package orientation on the PCB and use pin 1 marking consistently with the selected package drawing.
Terminate the differential bus at the physical ends, not at every node, and keep branch stubs short. The 5 Mbps capability supports short, well-controlled links, but cable length, topology, connector loss, and propagation delay still determine whether the installation remains reliable. Provide chassis grounding and an appropriate external surge-protection strategy for installations where the cable can extend beyond the equipment enclosure.
زانیاری پابەندبوون
The LCSC product listing identifies the ISL8485EIP as RoHS compliant. AEC-Q100 qualification is not applicable to this general-purpose interface transceiver. Other compliance attributes require confirmation from the manufacturer.