Renesas Electronics

ISL8485EIP - 5V RS-485/RS-422 Transceiver | Renesas

MPN: ISL8485EIP ✓ فعال
4.5 V to 5.5 V Vdss 8-pin PDIP Package
MOQ: 1 |

ISL8485EIP جائزہ

The Renesas Electronics ISL8485EIP is a 5 V, single RS-485/RS-422 transceiver with integrated ESD protection, packaged in an 8-pin PDIP. It provides one half-duplex driver and receiver for balanced industrial communication links, accepts a supply range of 4.5 V to 5.5 V, and is designed for data rates up to 5 Mbps. Each driver output and receiver input is protected against ±15 kV ESD strikes without latch-up.

An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential balanced signals. RS-485 supports longer multipoint buses and common-mode noise tolerance, while RS-422 favors point-to-point, full-duplex communication. The ISL8485EIP belongs to the transceiver hierarchy: interface transceiver → differential line driver and receiver → communications interface IC.

The principal benefits of the ISL8485EIP are its ±15 kV ESD protection, 4.5 V to 5.5 V supply tolerance, low-power BiCMOS implementation, and selectable high-speed or slew-rate-limited operation. Driver short-circuit current limiting and on-chip thermal shutdown improve robustness during bus contention. These characteristics suit equipment connected to industrial wiring where electrostatic discharge and ground-potential differences are common.

The device supports both RS-485 and RS-422 balanced communication. Its driver outputs and receiver inputs are protected against ESD events, while the receiver can provide a fail-safe output when the bus is idle. The device operates from a single 5 V rail, allowing integration with conventional 5 V control logic. Exact propagation-delay, receiver-threshold, and load-current limits should be confirmed against the manufacturer datasheet before release.

Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, data acquisition, and communications interfaces that require protection from cable-borne electrostatic discharge. The device is particularly useful where a 5 Mbps bus must tolerate electrical transients at exposed connector pins. PCB layout still requires a controlled return path and careful connection of the external interface network.

Place protection and termination components close to the transceiver pins, route the differential pair as a tightly coupled pair, and provide a low-impedance ground reference. Respect the datasheet limits for driver load, receiver input, and supply bypassing. Keep analog and digital return currents separated where possible to reduce common-mode conversion and improve signal integrity.

This page combines the manufacturer interface description, package information, sourcing data, and practical design guidance to support component selection. It also distinguishes the pin-compatible family alternatives from functionally similar devices that may require different package or operating details, helping engineers narrow a replacement without assuming interchangeability.

کے لیے ڈراپ اِن متبادل ISL8485EIP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ISL8485EIP (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف ESD Protection, Product Type, Supply Voltage Range.

Renesas Electronics
ESD Protection: ±15 kV
موازنہ کریں ISL8485EIP →
Maxim Integrated
ESD Protection: 15 kV
Supply Voltage Range: 4.75 V to 5.25 V
موازنہ کریں ISL8485EIP →
MaxLinear
Product Type: Half-duplex RS-485/RS-422 transceiver
موازنہ کریں ISL8485EIP →

ISL8483EIP

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Renesas Electronics
📦 PDIP-8
Single RS-485/RS-422 transceiver · 1 transmitter and 1 receiver · 5 V · ±15 kV · RS-485 and RS-422 · BiCMOS · On-chip short-circuit current limiting · On-chip thermal shutdown

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ISL8485EIPZ

✅ ڈراپ-اِن
📦 PDIP-8
Same 8-pin PDIP package and closely related functional characteristics; ordering or qualification attributes may differ by suffix.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SP485EEP-L

✅ ڈراپ-اِن
MaxLinear
📦 PDIP-8
Half-duplex RS-485/RS-422 transceiver · 5 Mbps · 5 V · RS-485 and RS-422 · BiCMOS · Over ±15 kV · Over ±15 kV · -40°C to +85°C

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX485EEPA+

✅ ڈراپ-اِن
Maxim Integrated
📦 PDIP-8
1 transmitter and 1 receiver · RS-422 and RS-485 · Half-duplex · 4.75 V to 5.25 V · 15 kV · Low-power · Slew-rate-limited · 1 data input

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ISL8485EIP تفصیلات

Product Type Single RS-485/RS-422 transceiver
Number of Transceivers 1 transceiver
Communications Modes RS-485 and RS-422
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 5 Mbps
Driver and Receiver Count 1 driver and 1 receiver
Driver Output Protection Short-circuit current limiting
Thermal Protection On-chip thermal shutdown
ESD Protection ±15 kV on each driver output and receiver input
ESD Latch-up Protection Yes
Process Technology BiCMOS
پیکیج 8-pin PDIP
ماؤنٹنگ ٹائپ Through-hole
RoHS اسٹیٹس Compliant

ISL8485EIP 8-pin pdip پن کنفیگریشن گائیڈ

ISL8485EIP (8-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

ISL8485EIP کے لیے 8-pin pdip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ISL8485EIP.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

ISL8485EIP کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial RS-485 Control Networks, Building and HVAC Automation, Instrumentation and Data Acquisition, Security and Surveillance Systems, Industrial Sensor and Actuator Backplanes, Communication Port Cards and Gateways.

🏭

Industrial RS-485 Control Networks

The ISL8485EIP fits industrial RS-485 control networks that connect remote sensors, actuators, programmable controllers, and motor-drive modules over a shared differential bus. Its 5 Mbps maximum data rate supports high-bandwidth factory data paths, while the 4.5 V to 5.5 V supply range accommodates conventional 5 V industrial logic. The ±15 kV ESD protection on each driver output and receiver input improves robustness at factory wiring boundaries. Bus contention is addressed by driver short-circuit current limiting and thermal shutdown. Designers should still preserve controlled return paths, minimize cable stubs, and verify termination and fail-safe behavior for the selected network topology.

🏠

Building and HVAC Automation

The ISL8485EIP can connect thermostats, variable-air-volume controllers, room sensors, and supervisory controllers in building and HVAC automation systems. RS-485 differential signaling helps maintain data integrity across long cables and environments containing switching loads. The transceiver's 5 V operation suits embedded controls that already regulate their logic rail, while ±15 kV ESD protection adds robustness where field wiring enters an enclosure. Its short-circuit limiting and thermal shutdown protect the interface during inactive, miswired, or contended bus conditions. Confirm the receiver thresholds and idle-state behavior against the automation network specification before commissioning the controller board.

🔧

Instrumentation and Data Acquisition

The ISL8485EIP is appropriate for instrumentation links carrying commands and measurements between a data-acquisition controller and remote front-end equipment. The 5 Mbps rate supports the data throughput of compact measurement systems, while thebalanced differential interface reduces susceptibility to common-mode noise found near motors and power converters. Integrated ESD protection helps protect the controller from electrostatic discharge introduced through measurement cables. Use the receiver in the correct enabled state during bus idle, provide a solid analog and digital ground strategy, and follow the manufacturer component placement and external-network recommendations to preserve signal integrity.

🎥

Security and Surveillance Systems

The ISL8485EIP can interface control panels, access-control readers, intercom stations, and distributed camera-control modules using RS-485. The device supports communication rates up to 5 Mbps, allowing short-distance command and status links to operate with low protocol overhead. Its ±15 kV ESD protection is particularly relevant for cabinet and outdoor wiring interfaces exposed to human contact or nearby charged objects. Short-circuit current limiting and thermal shutdown improve resilience during bus contention. The circuit should still include connector grounding, controlled cable routing, and the correct termination network to avoid reflections and excessive common-mode conversion.

🔧

Industrial Sensor and Actuator Backplanes

The ISL8485EIP supports compact backplanes that connect distributed sensors, relay outputs, valve controllers, and motor-control modules. A 5 Mbps bus rate allows command traffic and status feedback to share the same balanced wiring when the network protocol permits. Because industrial backplanes may be exposed to plug-in cards and differing ground potentials, the transceiver's ±15 kV ESD protection, current-limited driver, and thermal shutdown add useful robustness. Validate the total bus length, node count, termination, and cable-stub geometry so that reflections do not reduce receiver margins.

🌐

Communication Port Cards and Gateways

The ISL8485EIP is useful in communication port cards, serial gateways, and legacy-equipment adapters that need an RS-485/RS-422 interface. Its 8-pin PDIP package supports through-hole assembly and straightforward prototyping, while the single transceiver architecture allows one port to handle a half-duplex RS-485 bus or a directional RS-422 connection. The ±15 kV bus-pin ESD protection is valuable when the port connects to external equipment. During design-in, verify enable polarity, receiver fail-safe behavior, propagation timing, and loading against the host UART and protocol timing to prevent framing errors.

What is the ISL8485EIP?
The ISL8485EIP is a 5 V, single RS-485/RS-422 transceiver from Renesas Electronics in an 8-pin PDIP package. According to the manufacturer datasheet, it uses BiCMOS technology, supports data rates up to 5 Mbps, and combines one balanced driver and one balanced receiver. The device is intended for industrial and instrumentation networks that require differential signaling and ±15 kV ESD protection on the exposed bus pins.
What are the key specifications of ISL8485EIP that engineers should know?
The ISL8485EIP operates from 4.5 V to 5.5 V, supports up to 5 Mbps, and provides ±15 kV ESD protection on every driver output and receiver input. It also includes driver short-circuit current limiting and on-chip thermal shutdown. The 8-pin PDIP package is suitable for through-hole industrial assemblies, while the 5 V supply operation allows straightforward interfacing with compatible 5 V control logic.
Where can I download the ISL8485EIP datasheet PDF?
The official ISL8483E and ISL8485E datasheet is available through the Renesas Electronics document page at https://www.renesas.com/en/document/dst/isl8483e-isl8485e-datasheet. It contains the electrical characteristics, application information, pin descriptions, ESD information, and operating details needed to evaluate the ISL8485EIP. Use the manufacturer document for final schematic, layout, and qualification decisions.
Where can I find the ISL8485EIP pinout?
The ISL8485EIP pinout is identified in the manufacturer pin-description table and package drawing within the ISL8483E and ISL8485E datasheet. The component uses an 8-pin PDIP configuration. Before assigning PCB nets, verify every pin number and signal against that table, especially the driver-enable, receiver-enable, driver-output, receiver-input, ground, and supply connections.
Is ISL8485EIP suitable for industrial RS-485 networks?
Yes, the ISL8485EIP is suitable for industrial RS-485 networks requiring robust differential communications. Its ±15 kV ESD protection, 4.5 V to 5.5 V supply tolerance, short-circuit current limiting, and thermal shutdown address common industrial bus hazards. The manufacturer identifies the device as meeting both RS-485 and RS-422 requirements, making it appropriate for factory automation, instrumentation, and building-control links.
What is the difference between ISL8485EIP and ISL8483EIP?
The ISL8485EIP and ISL8483EIP belong to the same Renesas BiCMOS transceiver family and are described together in the manufacturer datasheet. Their principal documented difference is operating mode or performance: the ISL8485E is associated with high-speed or slew-rate-limited operation, while the ISL8483E is the lower-speed family member. Confirm the exact speed and timing limits in the manufacturer comparison before substituting one for the other.
Can SP485EEP replace ISL8485EIP?
SP485EEP is identified in the substitute-part cross-reference information as a pin-to-pin replacement candidate for the ISL8485EIP. A mechanical match alone is not sufficient for production use: compare supply range, data rate, receiver thresholds, fail-safe behavior, ESD rating, enable logic, and thermal limits against the manufacturer datasheets. The candidate is most appropriate when those electrical characteristics remain within the original design requirements.
When should I choose ISL8485EIP over ISL8485EIPZ?
Choose ISL8485EIP when the original board and production documentation specifically call for the PDIP-8 ISL8485EIP configuration. The ISL8485EIPZ is shown as an 8-pin PDIP alternative with similar functional characteristics, but the suffix can represent a different qualification or ordering option. Review the manufacturer ordering table to confirm whether temperature grade, qualification status, or another ordering attribute differs before making a substitution.
What is the best drop-in replacement for ISL8485EIP?
The best drop-in replacement is the candidate that preserves the 8-pin PDIP footprint, pin functions, supply range, data-rate capability, and required protection level. SP485EEP is presented as a pin-to-pin replacement candidate, while MAX485EEPA also appears in related substitute information. Neither should be approved solely from its package name; verify driver enable polarity, receiver enable behavior, ESD rating, propagation delay, and bus loading against the original design.
Is ISL8485EIP the same as MAX485EEPA?
No, the ISL8485EIP and MAX485EEPA are different manufacturer devices even though MAX485EEPA appears in related substitute information. The ISL8485EIP is specified at up to 5 Mbps with ±15 kV ESD protection, while the MAX485EEPA requires a detailed parameter comparison. Treat it as a candidate replacement rather than an identical part until supply voltage, timing, logic levels, and protection ratings have been verified.
What can replace ISL8485EIP without changing the PCB?
A PCB-compatible replacement must use the same 8-pin PDIP footprint and preserve the original pin functions. SP485EEP is listed in the substitute information as a pin-to-pin candidate, and the ISL8485EIPZ comparison identifies another 8-PDIP alternative. Verify enable polarity, receiver thresholds, maximum data rate, ESD protection, and supply requirements in the manufacturer documentation before replacing the ISL8485EIP in production.
Where can I buy ISL8485EIP online?
Use the Request a Quote form on this page to request the current ISL8485EIP unit price, stock position, minimum order quantity, and lead time. The Request a Quote workflow gives the buyer a direct purchasing response for the exact PDIP-8 ordering code. Confirm the manufacturer, package suffix, and intended quantity when submitting the request so the returned commercial terms match the device being designed.
What is the price of ISL8485EIP?
Current commercial terms for the ISL8485EIP are available through the Request a Quote form on this page. Submit the exact MPN, required quantity, and destination country for a current quotation. Because price and availability can change with market conditions and order volume, the form is the appropriate source for actionable pricing rather than a static listing figure.
What is the lead time for ISL8485EIP?
The current lead time for ISL8485EIP should be requested through the Request a Quote form on this page. Include the required quantity, authorized quantity per order, target date, and shipment destination. A supplier can then confirm current factory or inventory allocation, expected processing time, and transit timing without relying on a potentially stale lifecycle estimate.
Is ISL8485EIP in stock?
Current ISL8485EIP stock status is best confirmed through the Request a Quote form on this page. Include the desired quantity and packaging requirement so the supplier can check the exact PDIP-8 ordering code. The live response can distinguish immediately available inventory from parts requiring factory allocation or a longer production lead time.
How should the ISL8485EIP PCB be protected against ESD?
Use the ISL8485EIP's ±15 kV-rated driver outputs and receiver inputs as the primary interface protection, while placing connector-side components close to the cable entry. Keep the differential pair tightly coupled, provide a continuous ground reference, minimize stub branches, and follow the manufacturer layout guidance. The on-chip ESD rating does not replace a correctly designed enclosure, grounding system, or complete cable surge-protection strategy.

کے لیے انجینئرنگ ریفرنس ڈیٹا ISL8485EIP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the ISL8485EIP when the design needs a 5 V, single RS-485/RS-422 transceiver with operation up to 5 Mbps and ±15 kV ESD protection on the bus pins. It is especially appropriate for industrial wiring exposed to electrostatic discharge, provided the 4.5 V to 5.5 V supply range and 8-pin PDIP footprint match the PCB. Consider ISL8485EIPZ for a closely related 8-pin PDIP ordering option after checking its suffix-specific attributes. ISL8483EIP is a same-family candidate when lower-speed operation is acceptable. SP485EEP and MAX485EEPA are cross-brand candidates whose data rate, receiver thresholds, logic controls, ESD rating, and fault behavior must be checked against the original circuit. For any replacement, pin compatibility is necessary but not sufficient: the bus protocol timing, loading, termination, grounding, and environmental protection must also remain valid.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ ISL8483EIP ISL8485EIPZ SP485EEP MAX485EEPA
Brand Renesas Electronics Renesas Electronics Renesas Electronics Maxim Integrated Maxim Integrated
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Transceiver Count 1 1 1 1 1

اہم امتیازی خصوصیات

  • Specified ESD resilience on all exposed bus pins (بمقابلہMAX485EEPA)
  • Wide 5 V supply tolerance (بمقابلہSP485EEP)
  • High-speed capability with configurable communication behavior (بمقابلہISL8483EIP)
  • Protected driver under bus contention (بمقابلہSP485EEP)

ڈیزائن نوٹس

Place the transceiver, supply bypass capacitor, and any termination or bias network close to their associated pins. Keep the RS-485/RS-422 driver and receiver traces as a tightly coupled differential pair with a continuous ground reference. Avoid routing the pair through switching-power regions or splitting it across unrelated copper zones, because those practices increase common-mode conversion and can reduce receiver margin.

Do not approve a substitute from package shape alone. Compare the original and candidate for driver-enable polarity, receiver-enable behavior, receiver thresholds, fail-safe state, propagation delay, maximum data rate, supply tolerance, and ESD rating. The ISL8485EIP also provides driver current limiting and thermal shutdown, so a candidate lacking equivalent protection may be unsuitable for exposed industrial wiring even if its pin arrangement matches.

Use the manufacturer pin-description and application-circuit information when assigning the PDIP-8 nets. In particular, verify the driver-enable and receiver-enable controls before connecting a UART because incorrect logic states can hold the bus in an active condition and prevent other nodes from communicating. Confirm the package orientation on the PCB and use pin 1 marking consistently with the selected package drawing.

Terminate the differential bus at the physical ends, not at every node, and keep branch stubs short. The 5 Mbps capability supports short, well-controlled links, but cable length, topology, connector loss, and propagation delay still determine whether the installation remains reliable. Provide chassis grounding and an appropriate external surge-protection strategy for installations where the cable can extend beyond the equipment enclosure.

تعمیل کی معلومات

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The LCSC product listing identifies the ISL8485EIP as RoHS compliant. AEC-Q100 qualification is not applicable to this general-purpose interface transceiver. Other compliance attributes require confirmation from the manufacturer.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-20 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

ISL8485EIP datasheet ISL8485EIP pinout ISL8485EIP datasheet pdf Renesas ISL8485EIP ISL8485EIP RS-485 transceiver ISL8485EIP 5 Mbps ISL8485EIP PDIP-8 ISL8485EIP ESD protection ISL8485EIP vs ISL8485EIPZ ISL8485EIP drop-in replacement ISL8485EIP equivalent ISL8485EIP price ISL8485EIP stock ISL8485EIP industrial RS-485

متعلقہ اجزاء اور اصطلاحات

Renesas Electronics ISL8485EIP ISL8483EIP ISL8485EIPZ SP485EEP MAX485EEPA RS-485 RS-422 differential transceiver balanced line driver differential line receiver interface transceiver communications interface IC BiCMOS PDIP-8 DIP package through-hole package 5 Mbps data rate 4.5 V to 5.5 V supply ±15 kV ESD protection driver short-circuit current limiting thermal shutdown industrial automation RoHS
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں