LAN9252TI/ML - 2/3-Port EtherCAT Controller | Microchip
MPN: LAN9252TI/ML ✓ چالاکLAN9252TI/ML گشتی
An EtherCAT slave controller, or ESC, is a specialized interface semiconductor that combines EtherCAT protocol processing, Ethernet physical-layer functions, and host communication. Within the industrial communication hierarchy, it links an EtherCAT master and slave network to an embedded controller. The ESC belongs to the broader category of Ethernet interface controllers, combining a communication controller, integrated PHYs, and a serial host interface in one package.
The principal advantages of the LAN9252TI/ML include its two integrated Ethernet PHYs, support for both copper and external-transceiver fiber connectivity, and a 64-QFN package that supports compact industrial control designs. The 1.8 V, 2.5 V, and 3.3 V operating options support systems using multiple logic-rail levels. HP Auto-MDIX allows direct or crossover cables to be used without manually configuring receive and transmit pairs.
Technically, each integrated PHY contains a full-duplex 100BASE-TX transceiver capable of 100 Mbps operation. The SPI interface provides host access to EtherCAT control functions, while the ESC architecture reduces the number of external Ethernet components required by a slave-node design. The 9 x 9 mm QFN format offers a practical footprint for motion-control, robotics, industrial automation, and embedded equipment, although careful decoupling and high-speed layout remain necessary.
Typical applications include EtherCAT servo drives, programmable logic controllers, robot controllers, industrial I/O modules, machine vision equipment, and industrial communication gateways. The integrated PHYs are especially useful when a design requires two 100BASE-TX ports and an EtherCAT link to a higher-level master network without using discrete Ethernet transceiver components.
Designers should place input and output decoupling capacitors close to their associated supply pins, route Ethernet pairs as controlled-impedance differential pairs, and maintain the separation specified by the LAN9252 datasheet. The external 100BASE-FX arrangement also requires careful review of transceiver interface timing, signal polarity, and isolation requirements when fiber support is required.
جێگرەوەکانی جێگۆڕکێ بۆ LAN9252TI/ML — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9252TI/ML (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Host Interface, Package, Product Type, Mounting Type, Ethernet Speed.
LAN9252/ML
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LAN9252I/ML
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LAN9252TI/ML تایبەتمەندییەکان
| Product Type | 2/3-port EtherCAT slave controller |
| Integrated Ethernet PHY Count | 2 PHYs |
| Ethernet Data Rate | 100 Mbps |
| Copper Ethernet Support | 100BASE-TX full-duplex |
| Fiber Ethernet Support | 100BASE-FX through an external fiber transceiver |
| Host Interface | SPI |
| Auto-MDIX | HP Auto-MDIX supported |
| Operating Voltage Options | 1.8 V, 2.5 V, or 3.3 V |
| پاکێج | 64-QFN (9 x 9 mm) |
| جۆری دامەزراندن | Surface mount |
| EtherCAT Port Configuration | 2/3-port |
ڕێنمایی ڕێکخستنی پینی LAN9252TI/ML 64-qfn (9 x 9 mm)
ڕێکخستنی پین بۆ LAN9252TI/ML (پاکێجی 64-qfn (9 x 9 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9252TI/ML.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LAN9252TI/ML گونجاوە بۆ 6 بەکارھێنانs: EtherCAT Servo Drive, Industrial I/O Module, Robotics Controller, Machine Vision Gateway, 100BASE-FX Fiber Gateway, Compact PLC Communication Module.
EtherCAT Servo Drive
The LAN9252TI/ML fits an EtherCAT servo-drive slave because its 2/3-port controller architecture connects the motion-control electronics to a fieldbus network while two integrated PHYs support 100 Mbps copper Ethernet links. The SPI host interface lets a real-time MCU or DSP manage EtherCAT registers, while HP Auto-MDIX simplifies connections to standard network equipment. In a dual-port drive design, one PHY can participate in the line topology and the other can provide an uplink. The 64-QFN 9 x 9 mm package helps preserve board area, but designers should follow the manufacturer’s exact decoupling, differential-pair routing, and exposed-pad thermal-land instructions.
پێشنیارکراو
Industrial I/O Module
The LAN9252TI/ML is appropriate for distributed industrial I/O where multiple EtherCAT ports reduce the number of network interfaces required on each module. Its two integrated 100BASE-TX PHYs support 100 Mbps full-duplex communication, and HP Auto-MDIX permits direct or crossover cabling in field installations. An embedded processor can use the SPI interface for cyclic process data and diagnostics. The 64-QFN package is useful for DIN-rail or compact carrier-board designs. Compliance with the final equipment’s industrial EMC, temperature, isolation, and functional-safety requirements must be established at the system level rather than inferred solely from the controller.
پێشنیارکراو
Robotics Controller
The LAN9252TI/ML supports EtherCAT-connected robot controllers where deterministic network communication is needed alongside local motion-processing electronics. Its 2/3-port arrangement can support line topologies or network uplinks, while the integrated PHYs eliminate two discrete 100BASE-TX transceiver positions. The SPI interface allows a dedicated real-time controller to exchange cyclic commands and status data without a separate Ethernet host interface. The compact 64-QFN package is well suited to robot-controller boards with limited area. Engineers should preserve controlled-impedance Ethernet routing, provide suitable supply decoupling, and verify synchronization and recovery behavior against the EtherCAT system requirements.
پێشنیارکراو
Machine Vision Gateway
The LAN9252TI/ML can serve as the EtherCAT interface in a machine-vision gateway that bridges cameras or inspection equipment to a motion-control network. Two integrated 100BASE-TX PHYs permit direct copper links and network distribution at 100 Mbps, while the SPI interface connects the gateway processor to the ESC register and interrupt resources. The 64-QFN package leaves board space for image-processing or interface electronics. In practical implementations, video transport should remain separate from the deterministic EtherCAT traffic where required, and Ethernet traces must be isolated from high-speed switching nodes. Cable, optical-isolation, and enclosure-grounding decisions should follow the equipment’s installation environment.
پێشنیارکراو
100BASE-FX Fiber Gateway
The LAN9252TI/ML can anchor a mixed copper-and-fiber EtherCAT gateway because its integrated PHYs handle 100BASE-TX copper while the controller supports 100BASE-FX through an external fiber transceiver. This allows an industrial network to extend over fiber without requiring a separate Ethernet controller beside the ESC. The SPI host interface can support configuration, diagnostics, and EtherCAT data exchange through an embedded processor. Fiber deployment requires careful review of transceiver compatibility, signal mapping, isolation, connector mechanics, and optical budget. Board placement should keep the external transceiver and its high-speed or differential circuitry away from sensitive analog sections and follow the manufacturer’s application guidance.
پێشنیارکراو
Compact PLC Communication Module
The LAN9252TI/ML fits a compact PLC communication module that must expose EtherCAT connectivity without consuming a large portion of the controller board. The 2/3-port controller supports segmented fieldbus networks, and the two integrated PHYs provide 100 Mbps copper links with HP Auto-MDIX. A microcontroller can connect through SPI and manage protocol processing, diagnostics, and data exchange. The 64-QFN 9 x 9 mm package is advantageous in compact DIN-rail products. Designers should budget adequate board area around the controller for stable supply bypassing, thermal spreading through the exposed pad, and controlled-impedance routing of every 100BASE-TX differential pair.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LAN9252TI/ML — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LAN9252/ML | LAN9252I/ML |
|---|---|---|---|
| Package | 64-QFN (9 x 9 mm) | 64-QFN (9 x 9 mm) - same | 64-QFN (9 x 9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Controller Architecture | 2/3-port EtherCAT slave controller | 2/3-port EtherCAT slave controller | 2/3-port EtherCAT slave controller |
| Integrated Ethernet PHYs | 2 PHYs | 2 PHYs | 2 PHYs |
| Ethernet Data Rate | 100 Mbps | 100 Mbps | 100 Mbps |
| Copper Ethernet | 10/100BASE-TX | 10/100BASE-TX | 10/100BASE-TX |
| Host Interface | SPI | SPI | SPI |
| Auto-MDIX | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported |
| Fiber Support | 100BASE-FX through external transceiver | 100BASE-FX through external transceiver | 100BASE-FX through external transceiver |
جیاکەرەوە سەرەکییەکان
- Integrates two 100BASE-TX PHYs with the EtherCAT controller (بەراورد بەLAN9252/ML)
- Supports copper and optional fiber connectivity (بەراورد بەLAN9252I/ML)
- Compact 64-QFN integration (بەراورد بەLAN9252/ML)
- SPI-connected embedded host architecture (بەراورد بەLAN9252I/ML)
تێبینییەکانی دیزاین
Route each 100BASE-TX pair as a controlled-impedance differential pair with the spacing and length matching specified by the Microchip LAN9252 datasheet. Keep PHY traces away from switching regulators, high-current motor paths, crystals, and isolation barriers. Place the external 100BASE-FX transceiver and its associated passive components close to the appropriate controller connections, while maintaining clear isolation boundaries in industrial systems.
Place all required decoupling capacitors adjacent to the corresponding supply and ground pins, with short ground returns and minimal loop area. Use the manufacturer’s recommended capacitor types, voltage ratings, and effective capacitance across the required frequency range. The 64-QFN exposed pad must use the specified land pattern and thermal-via arrangement; confirm via count and spacing against the package drawing before release.
Do not substitute a controller solely because it also supports EtherCAT and uses a similar pin count. Verify every power pin, ground connection, reset or clock connection, Ethernet PHY interface, and host-interface signal against the manufacturer pin-description table. Also review errata for operational differences and recommended workarounds, especially before using the device in production equipment.
Separate the controller’s digital supply requirements from noisy actuator and motor supplies. Check input-voltage tolerance, supply sequencing, startup behavior, and decoupling requirements in the official electrical tables. In a 3.3 V system, ensure every connected network device and transceiver supports the selected interface levels; level translation should not be added unless the application requires it and timing margins remain acceptable.
زانیاری پابەندبوون
No definitive compliance declaration for the exact LAN9252TI/ML ordering code was included in the product documentation excerpts. The component is an industrial Ethernet interface controller rather than an automotive-qualified device.