Microchip Technology

LAN9253-V/R4X - 2/3-Port EtherCAT Slave Controller | Microchip

MPN: LAN9253-V/R4X ✓ چالاک
1.14 V to 1.26 V (1.20 V nominal) Vdss 64-QFN (9x9 mm) Package
MOQ: 1 |

LAN9253-V/R4X گشتی

The Microchip Technology LAN9253-V/R4X is a 2/3-port EtherCAT slave controller (ESC) with two integrated 100BASE-TX Ethernet PHYs, a 1.20 V nominal core supply operating from 1.14 V to 1.26 V, and a 3.3 V I/O rail, housed in a 64-QFN (9x9 mm) surface-mount package.

An EtherCAT slave controller, also called an ESC, is the real-time protocol engine that decodes EtherCAT datagrams, manages distributed clocks, and drives the cyclic process data exchange on an EtherCAT segment. The LAN9253 sits between the fieldbus network and the application microcontroller, and integrates the EtherCAT protocol stack, the physical layer, and the host interface into one device. In system hierarchy it is a network controller, an interface IC, and ultimately a power management and connectivity semiconductor for industrial automation equipment.

Differentiating features include HP Auto-MDIX, which allows direct or crossover cables without manual crossover wiring, and full-duplex 100 Mbps 100BASE-TX operation on both integrated PHYs. The device exposes four serial I/O channels with NRZI encoding at up to 12.5 Mbps, plus I2C and SPI host interfaces, and supports 8-bit or 16-bit parallel host buses, GPIO, and MII. The industrial temperature range runs from -40 °C to +105 °C, and the device is manufactured on a CMOS process.

The third port is configurable as an MII port that can be connected to an external PHY, allowing a two-port or three-port device in one design. Host communication uses an SRAM-like client interface that gives a glueless connection to most 8-bit and 16-bit microcontrollers as well as 32-bit devices, as described in the Microchip connectivity options application note AN3762. The LAN9253 hardware design checklist document 00003644B covers the supported host bus, GPIO, SPI, and MII configuration options and strap-based setup.

Typical applications include servo drive and inverter control, industrial I/O modules, robot joints, motion controllers, and machine vision systems that need deterministic EtherCAT cyclic communication with the controller mounted close to the actuator.

When designing around this device, follow the Microchip LAN9253 hardware design checklist for strap resistors, core and I/O decoupling, and the differential PHY layout, and use the LAN9252 to LAN9253 and LAN9254 migration guide AN3621 to confirm pin and strap differences before porting an existing board.

This page consolidates distributor availability, same-family drop-in ordering options, package details, and practical design notes that are not laid out in a single place in the manufacturer documentation.

جێگرەوەکانی جێگۆڕکێ بۆ LAN9253-V/R4X — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9253-V/R4X (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Auto-MDIX, Ethernet Data Rate, SyncManagers, Core Supply Voltage.

Microchip Technology
Package: 64-QFN 9x9 mm
Auto-MDIX: HP Auto-MDIX
Ethernet Data Rate: 100 Mbps
Microchip Technology
Package: 64-QFN (HVQCCN), 9 x 9 mm
Ethernet Data Rate: 100 Mbps
SyncManagers: 8 SyncManagers
Microchip Technology
Package: 64-QFN (9 x 9 mm) with exposed pad
SyncManagers: 8

LAN9253/R4X

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 QFN-64 (9x9 mm)
2/3-port EtherCAT device controller · 2/3-port EtherCAT slave controller · 2 integrated 100BASE-TX PHYs · 100 Mbps · Yes · HP Auto-MDIX · 8/16-bit host bus, GPIO, SPI, and MII · 8 FMMUs

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9253-I/R4X

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 QFN-64 (9x9 mm)
2/3-port EtherCAT slave controller · 3 ports · 2 PHYs · 100BASE-TX · 100 Mbps · Full duplex · HP Auto-MDIX supported · 8/16-bit parallel host bus

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9253T/R4X

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 QFN-64 (9x9 mm)
2/3-port EtherCAT Slave Controller (ESC) with integrated PHYs · 2 x 100BASE-TX full-duplex (3 ports maximum) · 100 Mbps per port · HP Auto-MDIX supported · 8 Fieldbus Memory Management Units · 8 · Parallel 8-bit / 16-bit bus for 8-bit and 16-bit embedded controllers; 8/16-bit bus for 32-bit embedded controllers · 1.8 V to 3.3 V variable voltage

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9253T-V/R4X

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 QFN-64 (9x9 mm)
2/3-port EtherCAT slave controller · 2/3 ports · 2 PHYs · 100BASE-TX · 100 Mbps · Full duplex · HP Auto-MDIX · 8 FMMUs

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9253-V/R4X تایبەتمەندییەکان

Device Type 2/3-port EtherCAT slave controller (ESC)
Integrated Ethernet PHYs 2 x 100BASE-TX full-duplex transceivers
Ethernet Data Rate 100 Mbps per port
Core Supply Voltage 1.14 V to 1.26 V (1.20 V nominal)
I/O Supply Voltage 3.3 V
مەودای پلەی گەرمیی کارکردن -40 °C to +105 °C
پاکێج 64-QFN (9x9 mm)
جۆری دامەزراندن Surface mount
Serial I/O Channels 4 channels
Maximum Serial Data Rate 12.5 Mbps
Data Encoding NRZI
Host Interface Options 8/16-bit parallel host bus, SPI, I2C, GPIO, MII
Auto-MDIX HP Auto-MDIX supported
Port Configuration Two-port or three-port device, third port configurable as MII
Process Technology CMOS
Interface Classification 10/100 Base-T/TX bus interface Ethernet controller
Order Code Marking R4X
دۆخی RoHS Compliant
REACH Status Compliant

ڕێنمایی ڕێکخستنی پینی LAN9253-V/R4X 64-qfn (9x9 mm)

ڕێکخستنی پین بۆ LAN9253-V/R4X (پاکێجی 64-qfn (9x9 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 64-qfn (9x9 mm) بۆ LAN9253-V/R4X

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9253-V/R4X.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LAN9253-V/R4X گونجاوە بۆ 6 بەکارھێنانs: EtherCAT Servo Drive and Inverter Control, Industrial Distributed I/O Module, Robotics Joint and Sensor Network Controller, Machine Vision and Inspection Systems, Industrial PLC and Embedded Control Platform, Power Conversion and Energy Management Equipment.

🏭

EtherCAT Servo Drive and Inverter Control

The LAN9253-V/R4X fits the real-time communication boundary of a servo amplifier because the two integrated 100BASE-TX PHYs provide full-duplex 100 Mbps EtherCAT connectivity with HP Auto-MDIX, so both direct and crossover cables work without a switch. The 8/16-bit parallel host bus mode gives the motion-control MCU fast access to the EtherCAT mailbox and process data, while the 1.20 V core supply (1.14 V to 1.26 V) and 3.3 V I/O rail match typical mixed-signal control boards. In a drive, the ESC sits beside the current and position loops, exchanging cyclic objects such as target position, actual position, and fault flags. The -40 °C to +105 °C grade covers sealed cabinets where drive dissipation raises the internal ambient, and the 64-QFN (9x9 mm) footprint keeps the controller small next to the power stage and its magnetics. Compared with a discrete ESC plus external PHYs, the integrated PHY reduces board area, EMI troubleshooting, and the number of high-speed differential nets that must be routed.

🔧

Industrial Distributed I/O Module

Distributed I/O stations place the network interface close to the sensors and actuators, so the LAN9253-V/R4X is used as the module's EtherCAT slave endpoint. Two integrated 100BASE-TX PHYs let the module daisy-chain upstream and downstream ports without an external switch, and the third port can be configured as an MII interface if the design adds a third copper port through an external PHY. The SRAM-like client interface documented in application note AN3762 connects directly to an 8-bit or 16-bit MCU, which suits low-cost module controllers that also handle digital and analog channels. The 1.20 V core keeps controller power low in a bus-powered station, while the 3.3 V I/O rail drives level-shifted field inputs. The -40 °C to +105 °C range suits unheated factory cabinets, and the 64-QFN (9x9 mm) package leaves board area for terminal blocks and isolation components.

⚙️

Robotics Joint and Sensor Network Controller

Collaborative robot joints and mobile platforms need deterministic cyclic Ethernet on a small board, which is where the LAN9253-V/R4X is often placed. The device's EtherCAT slave controller handles distributed clock synchronization and the two 100BASE-TX PHYs support daisy-chained topology across multiple joints, with HP Auto-MDIX removing the crossover-cable constraint common in robot cabling. Because the controller draws its core from a 1.14 V to 1.26 V rail and its I/O from 3.3 V, it can share the same supplies as the joint's position MCU. The choice between the parallel host bus and the SPI interface lets the design trade board area against bus throughput, and the GPIO option supports direct drive of discrete joint sensors. The -40 °C to +105 °C grade is important in joints near motor heat sources, while the 64-QFN (9x9 mm) footprint preserves space for compact motor drivers.

📷

Machine Vision and Inspection Systems

Machine vision controllers typically need an EtherCAT slave port to move cameras, light controllers, and motorized stages over one deterministic network. The LAN9253-V/R4X provides that endpoint with two integrated 100BASE-TX PHYs, allowing a camera head to bridge upstream to the EtherCAT master and downstream to another vision device. The 100 Mbps full-duplex line rate matches the traffic profile of trigger and result frames, and HP Auto-MDIX makes installation simpler in plants where cable types vary. The SRAM-like client interface lets the vision controller's MCU access the EtherCAT process data with low software overhead, and the 8/16-bit parallel host bus option suits legacy PLC-adjacent controllers with limited SPI bandwidth. The -40 °C to +105 °C operating range suits unheated inspection cabinets, and the 64-QFN (9x9 mm) package keeps the control board compact for space-constrained optical housings.

🏭

Industrial PLC and Embedded Control Platform

Compact PLC and embedded control platforms add EtherCAT capability to an existing microcontroller design with the LAN9253-V/R4X rather than a dedicated fieldbus ASIC. The host MCU connects through the 8/16-bit parallel bus, SPI, or I2C, so an installed platform can gain EtherCAT without changing its processor, and the GPIO option provides direct linkage to local discrete I/O. The two integrated PHYs handle the standard copper EtherCAT port directly, and the third port can be brought out through an external PHY over MII when the platform needs more ports. Core supply of 1.14 V to 1.26 V with a 3.3 V I/O rail matches common industrial supply trees, and the -40 °C to +105 °C rating suits factory-floor cabinets. The 64-QFN (9x9 mm) package supports the compact board area typical of DIN-rail and edge modules.

⚡

Power Conversion and Energy Management Equipment

Inverters, power optimizers, and energy storage skids increasingly expose an EtherCAT endpoint so supervisory systems can log and command them. The LAN9253-V/R4X provides that endpoint with two integrated 100BASE-TX PHYs, and the industrial temperature range of -40 °C to +105 °C is valuable in power cabinets where internal temperatures run high because of switching losses. The device's separate 1.20 V core and 3.3 V I/O rails let the core supply be derived from the same converter that feeds the control MCU, which simplifies the power tree compared with a single-rail design. Because the host interface is SRAM-like, the supervisory MCU reads process data with minimal protocol overhead, and the 64-QFN (9x9 mm) footprint leaves room for the magnetics and busbar interfaces of a power module. The same silicon also suits metering and grid-support equipment needing deterministic cyclic reporting.

کورتەی بەرهەمە پێشنیارکراوەکان

STM32F103C8T6 STMicroelectronics بەکارهێنراوە لە: EtherCAT Servo Drive and Inverter Control, EtherCAT Servo Drive and Inverter Control STM32F103VET6 STMicroelectronics بەکارهێنراوە لە: EtherCAT Servo Drive and Inverter Control LAN9353T/PT Microchip Technology بەکارهێنراوە لە: EtherCAT Servo Drive and Inverter Control ATTINY48-MUR Microchip Technology بەکارهێنراوە لە: Industrial Distributed I/O Module PCA9554DWR Texas Instruments بەکارهێنراوە لە: Industrial Distributed I/O Module SN65HVD37D Texas Instruments بەکارهێنراوە لە: Industrial Distributed I/O Module STM32F401CCU6 STMicroelectronics بەکارهێنراوە لە: Robotics Joint and Sensor Network Controller DRV8833 Motor driver companion for joint actuators بەکارهێنراوە لە: Robotics Joint and Sensor Network Controller KSZ8041RNL Microchip Technology بەکارهێنراوە لە: Robotics Joint and Sensor Network Controller STM32F429ZIT6 STMicroelectronics بەکارهێنراوە لە: Machine Vision and Inspection Systems ISO1042DWVR Texas Instruments بەکارهێنراوە لە: Machine Vision and Inspection Systems MCP3424-E/SL Microchip Technology بەکارهێنراوە لە: Machine Vision and Inspection Systems STM32F103ZEH6 STMicroelectronics بەکارهێنراوە لە: Industrial PLC and Embedded Control Platform TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Industrial PLC and Embedded Control Platform MAX3485EESA RS-485/RS-422 interface for field expansion بەکارهێنراوە لە: Industrial PLC and Embedded Control Platform STM32G474RET6 STMicroelectronics بەکارهێنراوە لە: Power Conversion and Energy Management Equipment ADS1254E Texas Instruments بەکارهێنراوە لە: Power Conversion and Energy Management Equipment ISO121JUE4 Digital isolator for sensing front end بەکارهێنراوە لە: Power Conversion and Energy Management Equipment
What is the LAN9253-V/R4X?
The LAN9253-V/R4X is a 2/3-port EtherCAT slave controller from Microchip Technology that combines the EtherCAT protocol engine with two integrated 100BASE-TX Ethernet PHYs. According to the manufacturer product page, each PHY provides a full-duplex 100 Mbps 100BASE-TX transceiver, and the device supports HP Auto-MDIX so direct-connect or crossover cables both work. It is supplied in a 64-QFN (9x9 mm) package and connects to a host microcontroller through an 8/16-bit parallel bus, SPI, I2C, GPIO, or MII.
What is the core supply voltage of the LAN9253-V/R4X?
The LAN9253-V/R4X core supply operates from 1.14 V to 1.26 V with a nominal 1.20 V core, while the I/O and host interface rail runs at 3.3 V. The 1.14 V to 1.26 V core window and the 3.3 V I/O requirement are confirmed in the manufacturer ordering and product information. The low-voltage core keeps the internal protocol engine power-efficient, while the 3.3 V rail simplifies interfacing with 3.3 V microcontrollers and discrete I/O.
What is the operating temperature range of the LAN9253-V/R4X?
The LAN9253-V/R4X is specified for an industrial temperature range of -40 °C to +105 °C. That range makes the device suitable for factory automation, industrial I/O, and servo drive environments where the controller is mounted in an enclosure subject to internal heat rise. The same -40 °C to +105 °C envelope applies to the -V order code, whereas the LAN9253-I/R4X variant carries a different temperature grade, which is the main functional distinction between those two ordering codes.
Where can I download the LAN9253-V/R4X datasheet PDF?
The LAN9253-V/R4X datasheet PDF is available from the Microchip Technology LAN9253 product page at https://www.microchip.com/en-us/product/LAN9253, and a device-specific copy of the same document is also hosted at https://www.lcsc.com/datasheet/C3024367.pdf. For surrounding engineering documentation, the hardware design checklist document 00003644B covers strap settings, decoupling, and PHY layout, while application note AN3621 explains the pin and configuration strap differences when migrating from LAN9252 to LAN9253 or LAN9254.
Where can I find the LAN9253-V/R4X pinout and 64-QFN package drawing?
The authoritative pin definitions for the LAN9253-V/R4X are in the pin description tables of the manufacturer datasheet, and the 64-QFN (9x9 mm) mechanical outline with pin numbering is shown in the same document. The Microchip LAN9253 hardware design checklist document 00003644B adds layout-level guidance such as strap resistor locations and PHY trace routing. Use the datasheet pin-description tables when assigning PCB tracks and net names, and the package drawing for land pattern and solder mask design.
Which host interfaces does the LAN9253 support?
The LAN9253 supports several host interface options: an 8-bit or 16-bit parallel host bus, SPI, I2C, GPIO, and MII. Application note AN3762 describes the SRAM-like client interface that gives a glueless connection to most 8-bit and 16-bit microprocessors and microcontrollers as well as 32-bit devices. For designs where the controller must sit on a fast embedded bus, the parallel host bus mode offers lower overhead than a serial interface, while SPI and I2C suit low-pin-count hosts.
What is the difference between LAN9253-V/R4X and LAN9253/R4X?
The LAN9253-V/R4X and LAN9253/R4X are the same 2/3-port EtherCAT slave controller with dual integrated 100BASE-TX PHYs in a 64-QFN (9x9 mm) package; the difference is the ordering code. The -V order code designates the green, RoHS-compliant industrial-temperature variant rated from -40 °C to +105 °C, while the plain LAN9253/R4X is the standard-temperature ordering option. Both share identical PHY, host interface, and power architecture, so the choice is driven by environmental qualification and availability.
LAN9253-V/R4X vs LAN9253-I/R4X - which one is better for industrial automation?
For industrial automation equipment operating across the full industrial envelope, the LAN9253-V/R4X is the better match because it is specified from -40 °C to +105 °C. The LAN9253-I/R4X is the same 2/3-port EtherCAT slave controller with dual 100BASE-TX PHYs in the same 64-QFN (9x9 mm) package, but carries the -I order code with a narrower temperature grade. Both are pin-to-pin compatible for the same EtherCAT slave controller function, so the decision is a temperature qualification and part-numbering question, not a firmware or footprint question.
What is the best drop-in replacement for the LAN9253-V/R4X?
The closest drop-in replacements for the LAN9253-V/R4X are the same-family Microchip ordering codes: the LAN9253/R4X, the LAN9253-I/R4X, and the tape-and-reel packaged LAN9253T/R4X and LAN9253T-V/R4X. All keep the identical 2/3-port EtherCAT slave controller architecture, dual integrated 100BASE-TX PHYs, 1.20 V core, 3.3 V I/O, and the 64-QFN (9x9 mm) footprint, so no PCB respin or firmware change is required. Verify the temperature grade of the substitute against your enclosure conditions.
Can LAN9253T-V/R4X replace the LAN9253-V/R4X?
Yes, the LAN9253T-V/R4X can replace the LAN9253-V/R4X on an existing board. Both are the same Microchip 2/3-port EtherCAT slave controller with two integrated 100BASE-TX PHYs, identical 1.14 V to 1.26 V core and 3.3 V I/O rails, and the same 64-QFN (9x9 mm) pin arrangement, so the substitution is mechanical and electrical rather than functional. The T ordering code denotes the production packing format, so confirm reel format and quantity against your assembly line requirements.
What can replace the LAN9253-V/R4X in an existing EtherCAT slave design?
Replacing the LAN9253-V/R4X in an existing EtherCAT slave design is normally done with the other Microchip LAN9253 ordering codes: LAN9253/R4X, LAN9253-I/R4X, LAN9253T/R4X, or LAN9253T-V/R4X. All four use the same 64-QFN (9x9 mm) footprint and the same 2/3-port ESC with dual 100BASE-TX PHYs, so no layout change or host firmware rewrite is needed. Use application note AN3621 as the reference for strap and pin differences if you are moving between different LAN9253 configurations or from LAN9252.
Is the LAN9253-V/R4X suitable for EtherCAT servo drive control?
The LAN9253-V/R4X is well suited to EtherCAT servo drive and inverter control. The integrated dual 100BASE-TX PHYs remove the need for external magnetics-qualified transceivers on the standard copper port, HP Auto-MDIX simplifies cabling, and the 8/16-bit parallel host bus option gives a fast path to the motion-control microcontroller that runs the current and position loops. The -40 °C to +105 °C grade also covers hot drive cabinets. Keep in mind that EtherCAT cyclic performance is dominated by the host MCU and the DC configuration.
When should I choose the LAN9253-V/R4X over a discrete EtherCAT solution?
Choose the LAN9253-V/R4X when you want a single silicon device to provide the EtherCAT protocol engine, the 100BASE-TX physical layers, and the host interface in a 64-QFN (9x9 mm) package. A discrete alternative built from a separate ESC and external PHYs costs more in board area, adds an isolation and magnetics supply chain, and lengthens EMC debugging, while the integrated PHY approach is what the manufacturer offers as a cost-effective EtherCAT solution. Choose a discrete path only when you need non-EtherCAT Ethernet variants or very unusual PHY topologies.
Where can I buy the LAN9253-V/R4X online?
You can request the LAN9253-V/R4X through the Request a Quote form on this page, which routes your enquiry to the XAIPART sales desk for stock confirmation, lead time, and shipment scheduling. Manufacturer listings for this part are published by Microchip Technology, and authorized channel inventory is shown by the major global distributors. For the current price, the Request a Quote form on this page returns the live unit price and quantity breaks for the exact LAN9253-V/R4X ordering code.
What is the price of the LAN9253-V/R4X?
Pricing for the LAN9253-V/R4X is quotation-based and refreshed daily, so the current figure is returned by the Request a Quote form on this page rather than printed on the page body. That form returns the live unit price, the quantity-break schedule, and the currency of sale for the exact -V/R4X ordering code, together with the standard orderable quantity in the 64-QFN (9x9 mm) tape-and-reel format. Submitting the form also gives you a documented quote reference for budgeting.
What is the lead time and minimum order quantity for the LAN9253-V/R4X?
Lead time and minimum order quantity for the LAN9253-V/R4X depend on current factory and channel inventory, so confirm them through the Request a Quote form on this page. The part is normally shipped in the 64-QFN (9x9 mm) production packing format, and the manufacturer also offers tape-and-reel ordering codes such as LAN9253T-V/R4X for automated assembly. Ask the quote desk for the current minimum order quantity, the reel quantity per reel, and the scheduled lead time for your shipment schedule.
What are the key specifications of the LAN9253-V/R4X that engineers should know?
The key specifications of the LAN9253-V/R4X are: a 2/3-port EtherCAT slave controller function, two integrated 100BASE-TX full-duplex PHYs at 100 Mbps, HP Auto-MDIX, a 1.14 V to 1.26 V core supply with 1.20 V nominal, a 3.3 V I/O rail, an operating range of -40 °C to +105 °C, four serial I/O channels with NRZI encoding up to 12.5 Mbps, and a 64-QFN (9x9 mm) package. Host connectivity covers an 8/16-bit parallel bus, SPI, I2C, GPIO, and MII, with the third port configurable as MII for an external PHY.
Is there a cross-brand drop-in equivalent to the LAN9253-V/R4X?
There is no verified cross-brand drop-in equivalent to the LAN9253-V/R4X. The device combines an EtherCAT slave controller with two integrated 100BASE-TX PHYs and a specific 64-QFN (9x9 mm) pin arrangement including the host bus, MII port, and configuration straps, and no competitor part was found that reproduces that pin-for-pin. For a supply-continuity plan, treat the other Microchip LAN9253 ordering codes as the drop-in options, and use application note AN3621 to check pin and strap differences if you ever evaluate a LAN9254-based layout.

داتای سەرچاوەی ئەندازیاری بۆ LAN9253-V/R4X — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LAN9253-V/R4X when your design needs a 2/3-port EtherCAT slave endpoint with two integrated 100BASE-TX PHYs and the widest industrial temperature coverage, -40 °C to +105 °C, in a 64-QFN (9x9 mm) package. Pick LAN9253/I-R4X style ordering codes only when your thermal environment is milder and you want the -I grade; the silicon is otherwise identical. Use LAN9253T/R4X or LAN9253T-V/R4X when your assembly line is reel-fed, since the electrical content and footprint are unchanged and only the packing format differs. If you need an EtherCAT solution with an integrated host CPU, consider the LAN9353 family instead, which trades host interface flexibility for a built-in microcontroller. If you need more than three ports or a different physical layer, evaluate the LAN9254 or a discrete ESC plus external PHY architecture rather than forcing a respin. In every case, confirm the core and I/O rail sequencing, strap configuration, and PHY layout against the Microchip hardware design checklist.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LAN9253/R4X LAN9253-I/R4X LAN9253T/R4X LAN9253T-V/R4X
Package QFN-64 (9x9 mm) QFN-64 (9x9 mm) - same QFN-64 (9x9 mm) - same QFN-64 (9x9 mm) - same QFN-64 (9x9 mm) - same
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Device Function 2/3-port EtherCAT slave controller 2/3-port EtherCAT slave controller 2/3-port EtherCAT slave controller 2/3-port EtherCAT slave controller 2/3-port EtherCAT slave controller
Integrated Ethernet PHYs 2 x 100BASE-TX, 100 Mbps full duplex 2 x 100BASE-TX, 100 Mbps full duplex 2 x 100BASE-TX, 100 Mbps full duplex 2 x 100BASE-TX, 100 Mbps full duplex 2 x 100BASE-TX, 100 Mbps full duplex
Core Supply Voltage 1.14 V to 1.26 V (1.20 V nominal) 1.14 V to 1.26 V (1.20 V nominal) 1.14 V to 1.26 V (1.20 V nominal) 1.14 V to 1.26 V (1.20 V nominal) 1.14 V to 1.26 V (1.20 V nominal)
I/O Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Host Interface Options 8/16-bit parallel host bus, SPI, I2C, GPIO, MII 8/16-bit parallel host bus, SPI, I2C, GPIO, MII 8/16-bit parallel host bus, SPI, I2C, GPIO, MII 8/16-bit parallel host bus, SPI, I2C, GPIO, MII 8/16-bit parallel host bus, SPI, I2C, GPIO, MII
Serial I/O Channels / Max Data Rate 4 channels, NRZI, 12.5 Mbps max 4 channels, NRZI, 12.5 Mbps max 4 channels, NRZI, 12.5 Mbps max 4 channels, NRZI, 12.5 Mbps max 4 channels, NRZI, 12.5 Mbps max
Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX
Packing / Order Code Tray or tube order code -V/R4X Standard order code -R4X -I temperature grade order code Tape-and-reel order code Tape-and-reel with -V order code
Process Technology CMOS CMOS CMOS CMOS CMOS

جیاکەرەوە سەرەکییەکان

  • Three-port-capable EtherCAT slave controller with dual integrated 100BASE-TX PHYs (بەراورد بەLAN9253-I/R4X)
  • Wide 1.20 V core operating window of 1.14 V to 1.26 V (بەراورد بەLAN9253/R4X)
  • Multi-mode host connectivity on a single 64-QFN (9x9 mm) device (بەراورد بەLAN9253T-V/R4X)

تێبینییەکانی دیزاین

Follow the Microchip LAN9253 hardware design checklist document 00003644B for the PCB layout. Keep the core 1.20 V and 3.3 V I/O decoupling networks placed directly at the device supply pins, and keep the configuration strap resistors close to their pins with short, clean traces because strap levels are sampled at reset. Route the 100BASE-TX differential pairs from the integrated PHYs to the RJ-45 or M12 connector as a short, length-matched pair over a continuous ground plane, and avoid running the Ethernet pairs parallel with the MII or host-bus traces.

The core rail must stay inside 1.14 V to 1.26 V and the I/O rail at 3.3 V. Estimated: if the core rail is generated from a 1.20 V switching node with typical 3 % ripple, the worst-case excursion of about 36 mV sits inside the core window, but a poorly decoupled rail can momentarily fall below 1.14 V during load steps. Verify the core supply sequencing relative to the 3.3 V I/O rail and the host MCU, and confirm the reset strap state at power-up so the controller does not latch into an unintended host-bus configuration.

A frequent porting mistake is assuming the LAN9253 and LAN9252 are interchangeable. Application note AN3621 documents that the pin and configuration strap differences between LAN9252 and LAN9253/LAN9254 must be checked before dropping one into an existing board. A second common error is enabling the third port as MII without accounting for the external PHY and its own reference clock and isolation requirements. Verify the port-configuration straps, the host interface mode straps, and the external PHY design before the first prototype spin.

The 8/16-bit parallel host bus is sensitive to signal integrity because the SRAM-like client interface runs synchronously with the host clock. Estimated: at a 12.5 Mbps serial equivalent and typical 8-bit host timing, bus skew between the data and control lines must be kept well inside the host setup and hold windows, so route the host bus as a short, source-synchronous group and terminate unused lines per the datasheet recommendations. When SPI or I2C is used instead, series damping on the clock line helps suppress ringing on longer board traces.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The -V order code denotes the green, RoHS-compliant variant of the LAN9253 family; RoHS and REACH status are confirmed by the manufacturer part comparison data. AEC-Q100 qualification is not stated for this industrial EtherCAT controller, and lead-free, halogen-free, and conflict-minerals declarations were not published for this part.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lan9253 schematic lan9253 microchip lan9253 price lan9253 ethercat lan9253 pdf lan9253 board lan9253 vs lan9252 lan9253 spi LAN9253-V/R4X datasheet LAN9253-V/R4X pinout 64-QFN LAN9253-V/R4X drop-in replacement LAN9253 EtherCAT slave controller 100BASE-TX LAN9253 hardware design checklist LAN9253-V/R4X buy quote

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology LAN9253-V/R4X LAN9253/R4X LAN9253-I/R4X LAN9253T/R4X LAN9253T-V/R4X LAN9254 LAN9353 EtherCAT slave controller (ESC) Ethernet controller interface IC 100BASE-TX Ethernet PHY Auto-MDIX NRZI encoding MII interface SPI I2C host bus interface 64-QFN (9x9 mm) QFN package family surface mount AN3621 migration guide AN3762 connectivity options note RoHS REACH
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ