LM2901D - 30V Quad Differential Comparator | Texas Instruments
MPN: LM2901D ✓ چالاکLM2901D گشتی
A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level result indicating which input is higher. Within the semiconductor hierarchy, the LM2901D is a voltage comparator, a linear signal-conditioning IC commonly grouped with amplifier and interface functions. Its open-collector outputs require an external pull-up resistor, allowing several outputs to be wired together when the resulting wired-AND behavior is appropriate for the system.
The four independent channels make the LM2901D useful where several sensing decisions must be made in one package. Its open-collector output structure can drive TTL, CMOS, MOS, DTL, and ECL-compatible logic as identified in the manufacturer literature. The specified 300 ns response time supports general-purpose detection rather than the latency demanded by high-speed timing applications. Split-supply operation also permits bipolar sensing around a zero-volt reference.
The input stage emphasizes low bias current, which reduces disturbance of high-impedance sensor outputs. A typical 25 nA input bias current is suitable for many threshold and level-detection circuits, while the typical ±5 nA input offset current helps minimize imbalance between the differential inputs. These characteristics should be considered together with input common-mode limits, output pull-up requirements, and supply-voltage tolerances during design verification.
Typical uses include monitoring battery or power rails, detecting overvoltage and undervoltage conditions, comparing sensor thresholds, implementing window comparators, and providing four-channel status indication. Because all four outputs are open collector, a pull-up resistor is normally required on each channel. Connecting multiple open-collector outputs to one pull-up can reduce the number of logic signals, but it also creates a shared fault domain and requires careful analysis of output leakage and pull-up current.
A practical design must preserve adequate input common-mode headroom at both supply rails, keep differential input voltage within the absolute maximum limits, and select pull-up resistors for the voltage and sink-current requirements of the connected logic. Decoupling capacitors should be placed close to the supply pins, while unused comparator inputs should be tied to a defined potential rather than left floating.
This page organizes the key LM2901D electrical characteristics, manufacturer-backed comparison options, pin-package constraints, and application guidance for engineers evaluating a 14-pin quad comparator. It also highlights the practical trade-offs involved when selecting a drop-in alternative with different input offset, bias current, temperature range, or propagation timing.
جێگرەوەکانی جێگۆڕکێ بۆ LM2901D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2901D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Package, Operating Temperature Range, Response Time, Supply Voltage Range.
LM2901B
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM239DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901DG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901D زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Quad differential voltage comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | Single supply, 5 V to 36 V |
| Differential Input Voltage Range | ±1 V to ±18 V |
| Maximum Supply Voltage | 30 V |
| جۆری دەرچوون | Open collector |
| Propagation Delay | 300 ns |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5.0 nA typical |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C |
| پاکێج | 14-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Supply Configuration | Single or split supply |
| Logic Compatibility | TTL, CMOS, MOS, DTL, and ECL |
| Automotive Application | Supported |
ڕێنمایی ڕێکخستنی پینی LM2901D 14-pin soic
ڕێکخستنی پین بۆ LM2901D (پاکێجی 14-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2901D.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2901D گونجاوە بۆ 6 بەکارھێنانs: Industrial Threshold and Limit Detection, Battery Pack Voltage Supervision, Overvoltage and Undervoltage Protection, Sensor Threshold Switching, Automotive Status and Window Monitoring, Memory and Logic Interface.
Industrial Threshold and Limit Detection
The LM2901D fits industrial sensing systems that require several independent voltage decisions within one package. Its four differential channels can monitor reference thresholds, sensor outputs, or rail limits, while the typical 25 nA input bias current minimizes loading on high-impedance sensing networks. The specified 300 ns response time allows the comparator to react quickly to crossings, and the -40 °C to +125 °C operating range supports demanding industrial environments. Each open-collector output should use a pull-up matched to the receiving logic, and every input must remain within the applicable common-mode range.
پێشنیارکراو
Battery Pack Voltage Supervision
The LM2901D can supervise several battery-related voltages with four independent differential channels. One pair may establish upper and lower limits for a pack, while another pair can monitor individual cell or auxiliary rails. Its typical 25 nA input bias current reduces the error introduced into high-impedance sensing paths, and the 300 ns propagation specification provides prompt fault signaling. Open-collector outputs suit alarm, shutdown, or wired-AND indicator circuits when paired with suitable pull-up resistors. The battery voltage itself must be checked against the comparator's input common-mode limits.
پێشنیارکراو
Overvoltage and Undervoltage Protection
The LM2901D is appropriate for independent overvoltage and undervoltage supervision because four channels can implement two complete window-comparator functions. A low reference is applied to one input of each channel while the monitored rail is applied to the other, allowing open-collector outputs to flag out-of-range conditions. Its 300 ns response time supports rapid fault detection, and the low typical input bias current reduces disturbance of source impedances. Design the pull-up network for the receiving fault controller and verify that the monitored rail remains within the device's common-mode operating region under every fault condition.
پێشنیارکراو
Sensor Threshold Switching
The LM2901D converts slow analog sensor outputs into logic-compatible threshold events, making it useful in condition-monitoring and instrumentation systems. Its typical ±5 nA input offset current and 25 nA input bias current help preserve accuracy when the source impedance is significant, while the four-channel configuration reduces package count. The open-collector output can pull up to the system's digital rail or participate in a wired-AND arrangement. Designers should account for the 300 ns response time, verify the input common-mode range at both supply extremes, and select pull-up resistors that balance signal rise time against output sink current.
پێشنیارکراو
Automotive Status and Window Monitoring
The LM2901D supports automotive status-monitoring functions involving multiple switched or continuously monitored voltages. Four independent channels can evaluate supply, actuator, or sensor thresholds, and the stated -40 °C to +125 °C operating range covers applications requiring extended temperature capability. The open-collector outputs are convenient for driving transistor-based warning or shutdown circuits through pull-up networks. Because formal automotive qualification depends on the exact manufacturer and ordering code, confirm AEC-Q100 documentation for the selected source before production release and verify all electrical limits against its datasheet.
پێشنیارکراو
Memory and Logic Interface
The LM2901D can support level detection and memory-related logic functions because it combines four differential inputs with open-collector outputs. A pulled-up output can represent a detected voltage state or interface with compatible TTL, CMOS, MOS, DTL, or ECL logic as identified in the manufacturer literature. The 300 ns propagation specification is suitable for general logic timing rather than high-speed edge-triggered systems. Each output should have a defined pull-up path, unused inputs should not float, and the logic family, voltage levels, fanout, and allowed sink current must be checked before connecting the device to a bus.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2901D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2901B | LM239DR | LM2901DG | LM2901D |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Comparator Channels | 4 | 4 | 4 | 4 | 4 |
جیاکەرەوە سەرەکییەکان
- Faster specified response than the improved LM2901B (بەراورد بەLM2901B)
- Lower typical input bias current in the improved B-version (بەراورد بەLM2901B)
- Four independent open-collector channels in a common SOIC footprint (بەراورد بەLM2901DG)
تێبینییەکانی دیزاین
Do not treat an LM2901D open-collector output as a push-pull logic output. Place one pull-up resistor per channel, connect it to the voltage expected by the receiving logic, and verify that the required low-state sink current remains within the device's output rating. When several outputs share one pull-up, confirm that simultaneous activation cannot exceed the pull-up resistor current or create an unintended fault condition.
Keep comparator input traces short and route them away from high-current switching nodes to reduce pickup of differential noise. Place the supply bypass capacitor close to the device's supply pins and provide a low-impedance return path. Because the specified typical input bias current is 25 nA, high-impedance sensor nodes deserve particular care, but the bias current and input offset must be checked together with resistor leakage and source impedance during error analysis.
Validate the complete supply configuration before applying power. The LM2901D supports single or split-supply operation, but the common-mode range of every input must remain valid at startup, shutdown, and during rail transitions. When using split supplies, verify both positive and negative rail limits against the specific manufacturer ordering code. Avoid relying on a nominal rail alone because transient overshoot can exceed the 30 V maximum supply rating.
Do not leave differential comparator inputs floating. Tie unused inputs to a defined reference within the allowed common-mode range and keep the input network resistant to oscillation. Also account for the 300 ns propagation time when defining alarm debounce or system timing. The manufacturer describes level-detection and low-level-sensing use, so relay chatter, slow sensor crossings, or output overshoot may require input filtering or hysteresis.
زانیاری پابەندبوون
The manufacturer literature identifies automotive applications for the LM2901 family, but the verified product information does not explicitly state AEC-Q100 qualification or the other compliance declarations for this exact ordering code.