STMicroelectronics

LM2902DT - Quad Op-Amp, 3-30V, SOIC-14 | STMicroelectronics

MPN: LM2902DT ✓ چالاک
3 V to 30 V Vdss 20 nA Id SOIC-14 (14-SO) Package Yes Speed
MOQ: 1 |

LM2902DT گشتی

The STMicroelectronics LM2902DT is a low-power quad operational amplifier with four independent, high-gain, internally frequency-compensated amplifier stages, a 1.3 MHz gain-bandwidth, 0.4 V/us slew rate, and a wide 3 V to 30 V single-supply operating range, housed in a 14-pin SOIC package.

An operational amplifier (op-amp) is an analog building block within the broader amplifier IC and linear IC families that amplifies the voltage difference between its two inputs. Quad op-amps integrate four of these stages in one package, letting a single IC handle multi-channel signal conditioning - sensor buffers, comparators-with-hysteresis, active filters, and summing stages - while sharing one supply rail and saving board area versus four single amplifiers.

Key features of the LM2902DT include single-supply operation from 3 V to 30 V (or dual supplies from +/-1.5 V to +/-15 V), an input common-mode range that extends to the negative rail, a 2 mV maximum input offset voltage, and approximately 20 nA input bias current - tighter than the classic LM324 (7 mV offset, 45 nA bias) - which improves accuracy in high-impedance sensor circuits. The bipolar process keeps quiescent current low, and output stages are push-pull with a classic footprint-compatible pinout shared industry-wide.

Per STMicroelectronics, the LM2902 family was designed specifically for automotive and industrial control systems; the D suffix denotes the 14-SOIC surface-mount package rated across the automotive temperature span. Internal frequency compensation means no external compensation components are needed at unity gain, simplifying design-in.

Typical applications include automotive sensor interfaces, industrial control loops, transducer amplifiers, active filters, and multi-channel DC signal conditioning in 12 V/24 V systems where the supply range and negative-rail input sensing fit naturally.

Design consideration: although the inputs sense down to the negative rail, the output cannot swing fully to the rail - allow roughly 1.5 V of headroom on VCC, or use a rail-to-rail output amplifier for low-side signal chains.

This page adds value beyond the datasheet by consolidating drop-in alternatives, application guidance, and comparison data for the LM2902DT in one place.

جێگرەوەکانی جێگۆڕکێ بۆ LM2902DT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902DT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Output Type, Input Offset Voltage, Supply Configuration.

Texas Instruments
Package: 14-SOIC
Supply Configuration: Single supply or split supply
بەراوردکردن لەگەڵ LM2902DT →
Texas Instruments
Package: 14-SOIC, 3.90 mm width
Amplifier Type: General Purpose
Input Offset Voltage: 2 mV
بەراوردکردن لەگەڵ LM2902DT →
Texas Instruments
Package: 14-SOIC
Supply Configuration: Single supply or split supply
بەراوردکردن لەگەڵ LM2902DT →
onsemi
Amplifier Type: General-purpose quad operational amplifier
Input Offset Voltage: 2 mV
Supply Configuration: Single supply
بەراوردکردن لەگەڵ LM2902DT →
Texas Instruments
Package: 8-pin SOIC
Output Type: Open collector
بەراوردکردن لەگەڵ LM2902DT →

LM2902DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14
Quad operational amplifier · 4 · 26 V · 1.2 MHz · 2 mV · Single supply or split supply · Push-pull

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324VDT

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14
LM324 wide-supply variant in same 14-SOIC footprint; same industry-standard pinout, higher supply ceiling variant

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2902D

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14
Quad operational amplifier · 4 · 26 V · 1.2 MHz · 2 mV · Single supply or split supply · Push-pull

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902DT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Configuration Quad (4 independent op-amps)
Amplifier Type General purpose, bipolar
Gain Bandwidth Product 1.3 MHz
Slew Rate 0.4 V/us
Supply Voltage Range (Single) 3 V to 30 V
Supply Voltage Range (Dual) +/-1.5 V to +/-15 V
Input Offset Voltage 2 mV (max)
Input Bias Current 20 nA
جۆری دەرچوون Push-Pull
Internal Frequency Compensation Yes
Input Common-Mode Range Includes negative rail
پاکێج SOIC-14 (14-SO)
جۆری دامەزراندن Surface Mount
ژمارەی پین 14
Target Markets Automotive and industrial control
دۆخی RoHS unknown

ڕێکخستنی پینی LM2902DT

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 VCC — Positive supply voltage
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 OUT3 — Output of amplifier 3
پین 9 IN3- — Inverting input of amplifier 3
پین 10 IN3+ — Non-inverting input of amplifier 3
پین 11 GND/VEE — Ground or negative supply
پین 12 IN4+ — Non-inverting input of amplifier 4
پین 13 IN4- — Inverting input of amplifier 4
پین 14 OUT4 — Output of amplifier 4

بەکارهێنانە باوەکان

LM2902DT گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Interfaces, Industrial Control Systems, Transducer Amplifier Circuits, Active Filter Networks, Comparator-Style Threshold Detection, Multi-Channel DC Signal Conditioning.

🚗

Automotive Sensor Interfaces

The LM2902DT is a natural fit for automotive sensor conditioning because STMicroelectronics designed the LM2902 family specially for automotive control systems. Its 3 V to 30 V single-supply range tolerates 12 V automotive rails with wide margin, and the input common-mode range extending to the negative rail lets ground-referenced sensors - throttle position potentiometers, pressure transducers, temperature dividers - be sensed directly without level shifting. Four independent amplifiers in one SOIC-14 package allow one IC to buffer several sensor channels, implement gain stages, and form window comparators simultaneously, cutting board area and BOM line count. Design with roughly 1.5 V output headroom on VCC and verify channel-to-channel crosstalk at your gain settings for multi-channel layouts.

🏭

Industrial Control Systems

In industrial control, the LM2902DT supplies the multi-channel analog front end for 24 V PLC-style environments: transducer amplification, error-amplifier stages inside control loops, and integrator/summing circuits. The 3 V to 30 V supply range covers 24 V industrial rails directly, and internal frequency compensation guarantees unity-gain stability without external components, which shortens design-in and reduces qualification effort. The 1.3 MHz bandwidth and 0.4 V/us slew rate are sufficient for typical process-control signal bandwidths (well under 100 kHz), while the 2 mV maximum offset voltage and 20 nA bias current keep DC accuracy acceptable in transducer bridges with moderate source impedance. Allocate output headroom near the rails and add RC filtering on long sensor runs to reject factory EMI.

🔧

Transducer Amplifier Circuits

Datasheet-typical transducer amplifier topologies map directly onto the LM2902DT: one amplifier buffers the bridge or sensor output, a second provides gain, and the remaining two form reference generation and offset nulling or alarm thresholds. Because the input common-mode range includes the negative rail, single-supply transducers referenced to ground work without negative supplies, and the 20 nA input bias current limits error when source impedances reach tens of kilohms. With a 2 mV maximum offset, gain-of-100 stages introduce roughly 200 mV of referred-to-output worst-case error, acceptable for industrial-grade measurements but worth calibrating out in precision paths. Use 1% gain resistors and place them close to the input pins to limit noise pickup.

🔧

Active Filter Networks

The LM2902DT implements multi-stage Sallen-Key, multiple-feedback, and state-variable active filters economically: four amplifier channels support a complete fourth-order filter or two independent second-order sections in one SOIC-14. The 1.3 MHz gain-bandwidth product supports cutoff frequencies up to roughly the tens-of-kilohertz range while keeping Q-enhancement and phase error manageable - a practical rule is to keep the filter corner at least 100x below the GBW for accurate response. Internal compensation guarantees stability at unity gain, so Sallen-Key unity-gain sections need no external compensation. Choose metal-film resistors and C0G capacitors for stable pole locations, and decouple each amplifier supply pin shared through pin 4 with local 100 nF ceramics.

⚡

Comparator-Style Threshold Detection

Although dedicated comparators are preferred for fast switching, the LM2902DT push-pull output stages allow its channels to act as low-speed comparators with hysteresis in non-critical industrial functions: over/under-voltage flags, level alarms, and relay drive decisions. Open-loop gains in the typical 100 V/mV class give sharp transitions, and because the input range includes the negative rail, thresholds near ground are sensed accurately. Add positive feedback resistors (typically 1-10 mV of hysteresis) around each channel to prevent chatter on slow-moving signals, and remember the output swing stops roughly 1.5 V short of VCC, so scale the driven load accordingly. For nanosecond-class response, pair this part with the LM2903 dual comparator instead.

🖥️

Multi-Channel DC Signal Conditioning

For panels that condition many slow DC signals - 4-20 mA receiver shunts, potentiometer position inputs, battery divider monitors - the LM2902DT consolidates four buffer/gain channels into one 14-SOIC, reducing placement count and per-channel cost. Single-supply operation from 3 V to 30 V means a single 24 V rail powers all channels, and low quiescent current suits always-on monitoring electronics. Each channel can be independently configured (unity buffer, non-inverting gain, difference amplifier) since the four amplifiers are fully independent. Watch offset voltage budgeting across cascaded channels (2 mV max per stage accumulates with gain) and reserve negative-rail input sensing for ground-referenced sources, since inputs must remain within the common-mode range at all times.

What is the supply voltage range of the LM2902DT?
The LM2902DT operates from a single supply of 3 V to 30 V, or from dual supplies of +/-1.5 V to +/-15 V. According to STMicroelectronics, the LM2902 quad op-amp family was designed specifically for automotive and industrial control systems, where 12 V and 24 V supply rails are common, and the wide supply range lets one design cover multiple rail voltages without redesign.
What is the gain bandwidth product of the LM2902DT?
The LM2902DT has a gain-bandwidth product of 1.3 MHz and a slew rate of 0.4 V/us. These figures suit low-to-moderate frequency analog signal conditioning: sensor buffers, active filters up to tens of kilohertz, and industrial control loops. For designs needing higher bandwidth, a faster amplifier such as a THS-series device is a better match, though it will not be pin-compatible in the same SOIC-14 footprint without verification.
What is the difference between the LM2902DT and LM2902DR?
The LM2902DT and LM2902DR are the same STMicroelectronics die and electrical specifications; the difference is the packing format suffix. Both come in the 14-SOIC surface-mount package with the identical industry-standard quad op-amp pinout, so they are drop-in interchangeable on the same PCB footprint. Choose the suffix that matches your assembly house's reel or tube handling requirements; electrically either part can replace the other with no redesign.
Can the TI LM2902D replace the ST LM2902DT?
Yes, the Texas Instruments LM2902D is a functionally equivalent drop-in replacement for the STMicroelectronics LM2902DT. Both are quad general-purpose op-amps in the 14-SOIC package with the same standard pinout, 3 V to 30 V single-supply range, and the LM2902 family's industrial/automotive heritage. Cross-reference listings such as Findchips compare these two parts directly. Always review the respective datasheets for minor parameter-table differences before approving a replacement in production.
Is the LM2902DT a replacement for the LM324N?
The LM2902DT is a functionally compatible drop-in replacement for the LM324N where a surface-mount 14-SOIC footprint is used, sharing the same pinout and family behavior. It even offers a slightly tighter input offset voltage (2 mV max vs 7 mV) and lower input bias current (20 nA vs 45 nA), which improve accuracy in high-impedance sensor circuits. Verify your supply range and temperature requirements against both datasheets before finalizing the substitution.
Where can I download the LM2902DT datasheet PDF?
The LM2902DT datasheet PDF is available from STMicroelectronics and from datasheet archives; a downloadable copy is linked on this page. STMicroelectronics publishes the LM2902 datasheet covering the quad op-amp family including the DT (SOIC-14) package variant. Note that Rohm also manufactures an LM2902DT under its Signature Series, so confirm the manufacturer marking on your physical part matches the datasheet revision you are designing from.
Where is the pinout of the LM2902DT documented?
The LM2902DT pinout is documented in the STMicroelectronics LM2902 family datasheet, in the pin description/connection diagram section. In the 14-SOIC package, pins 1-7 serve amplifier 1 and amplifier 2, and pins 8-14 serve amplifier 3 and amplifier 4, with VCC on pin 4 and GND/VEE on pin 11. This pinout is shared industry-wide across the LM2902/LM324 quad op-amp family, which is why so many cross-brand drop-in alternatives exist.
What are the key specifications of the LM2902DT that engineers should know?
Key LM2902DT specifications: four independent op-amps in a 14-SOIC package; 1.3 MHz gain-bandwidth product; 0.4 V/us slew rate; 3 V to 30 V single-supply (or +/-1.5 V to +/-15 V dual supply); 2 mV maximum input offset voltage; 20 nA input bias current; push-pull output stages; internal frequency compensation for unity-gain stability; and input common-mode range including the negative rail. The family targets automotive and industrial control applications per STMicroelectronics.
Is the LM2902DT suitable for automotive applications?
Yes. According to STMicroelectronics, the LM2902 family was designed specially for automotive and industrial control systems, and the LM2902DT in the 14-SOIC package is rated for the extended temperature span required by vehicle environments. Its wide 3 V to 30 V supply range tolerates automotive load-dump-adjacent rail conditions when combined with upstream protection. For new automotive designs requiring formal AEC-Q100 qualification documentation, verify the specific qualification level of the ordered suffix with STMicroelectronics before release.
When should I choose the LM2902DT over a modern rail-to-rail op-amp?
Choose the LM2902DT when you need a low-cost, low-power, proven quad amplifier for signals that do not require output swinging to the positive rail: sensor conditioning on 12 V/24 V industrial rails, multi-channel comparators-with-gain, and active filters. Choose a rail-to-rail output amplifier instead when your signal must approach the supply rails closely or when operating from a 3.3 V/5 V single rail where the LM2902's roughly 1.5 V output headroom consumes too much of the signal range.
What is the best equivalent for the LM2902DT?
The best equivalents for the LM2902DT are the Texas Instruments LM2902D (same 14-SOIC package, same quad LM2902 architecture, cross-referenced directly against this part) and the STMicroelectronics LM2902DR (same die and package, alternate packing format), plus the ST LM324VDT for designs favoring the LM324 wide-supply variant in the same footprint. All preserve the industry-standard quad op-amp pinout, so they solder directly onto the same PCB land pattern without layout changes.
Where to buy the LM2902DT online?
The LM2902DT can be purchased through the Request a Quote form on this XAIPART product page. Submit your required quantity and target delivery date, and XAIPART returns pricing, stock position, and lead time for the STMicroelectronics LM2902DT. Because industrial-grade quad op-amps are commonly stocked in reel and tube formats, quoting your annual usage often secures better pricing than single-piece purchases; state both in your quote request.
What is the price of the LM2902DT?
LM2902DT pricing depends on quantity, packaging format, and current stock, so XAIPART prices this part through its Request a Quote form on this page rather than a static table. For reference, this part is a commodity quad op-amp in the volume segment of the market, with distributor listings historically well under one US dollar per unit at volume. Request a quote with your exact quantity for a current, binding price and lead time.
What is the lead time and packaging for the LM2902DT?
The LM2902DT is supplied in the 14-SOIC surface-mount package; production quantities are typically delivered in tape-and-reel or tube format depending on the ordering suffix. Because this is an active, high-volume commodity amplifier, lead times are generally short when stock is on hand. Use the Request a Quote form on this page to confirm the current lead time, available packing format, and minimum order quantity for your delivery region before scheduling production.
What design precautions apply when using the LM2902DT?
Observe three precautions. First, the output cannot reach the positive rail - reserve roughly 1.5 V of headroom on VCC, and remember the output will not pull hard to the negative rail under load either. Second, the inputs sense down to the negative rail but not to VCC, so bias signals within the common-mode range. Third, decouple VCC with a 100 nF ceramic capacitor close to pin 4 and place gain-setting resistors tight to the inputs to limit offset and noise pickup in high-impedance nodes.

داتای سەرچاوەی ئەندازیاری بۆ LM2902DT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2902DT when you need a low-cost, proven quad amplifier for automotive or industrial signal conditioning on 12 V or 24 V single supplies, with ground-referenced sensor inputs and signal bandwidths well under 100 kHz. Choose the ST LM2902DR when you need the same electrical part in reel packing for production assembly - they are electrically identical. Choose the TI LM2902D for cross-brand second sourcing; it shares the same 14-SOIC footprint and LM2902 architecture. Choose the ST LM324VDT when your design needs a higher supply ceiling in the same footprint. Avoid this family when you need rail-to-rail output swing on 3.3 V/5 V rails, sub-millivolt offset precision, or bandwidth above 1 MHz - select a modern CMOS rail-to-rail or high-speed amplifier instead.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2902DR LM324VDT LM2902D
Package SOIC-14 SOIC-14 - same SOIC-14 - same SOIC-14 - same
Brand STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments
Number of Amplifiers 4 4 4 4
Gain Bandwidth Product 1.3 MHz 1.3 MHz 1.2 MHz 1.2 MHz
Supply Voltage Range (Single) 3 V to 30 V 3 V to 30 V 3 V to 32 V 3 V to 30 V
Output Type Push-Pull Push-Pull Push-Pull Push-Pull

جیاکەرەوە سەرەکییەکان

  • Tighter DC accuracy than the classic LM324 (بەراورد بەLM324N)
  • Automotive and industrial design heritage (بەراورد بەLM2902D (Texas Instruments))
  • Single-supply negative-rail input sensing (بەراورد بەLM324VDT)

تێبینییەکانی دیزاین

Decouple the shared VCC pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a bulk 1-10 uF capacitor per board region. Although the four amplifiers draw little quiescent current, load transients on one channel couple through the shared supply into the other three; local decoupling and a solid ground return on pin 11 keep channel-to-channel crosstalk low in multi-channel layouts.

Two classic LM2902 pitfalls: (1) expecting rail-to-rail output - the push-pull output stops roughly 1.5 V below VCC and does not pull hard to ground under load, so scale your signal range accordingly or select a rail-to-rail output amplifier; (2) driving inputs above the common-mode range - inputs sense down to the negative rail but not up to VCC, and phase reversal can occur outside the range. Verify bias points in single-supply 5 V systems where the usable output window is narrow.

Keep gain-setting and input resistors close to the input pins to minimize high-impedance node trace length - with 20 nA bias current and multi-Mohm effective node impedances, leaked flux residue or long traces add measurable offset and noise. Use a guard ring or ground pour around summing junctions in high-gain stages, and use 1% (or better) resistors for gain networks to control the 2 mV-referred offset budget across cascaded channels.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status for the ST LM2902DT should be confirmed on the STMicroelectronics product page for the exact ordering suffix.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm2902dt datasheet lm2902dt datasheet pdf lm2902dt pinout lm2902dt equivalent lm2902dt replacement lm2902dt cross reference lm2902dt vs lm2902d STMicroelectronics lm2902dt lm2902 quad op-amp 1.3 MHz SOIC-14 lm2902dt price lm2902dt stock lm2902 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

STMicroelectronics LM2902DT LM2902DR LM2902D LM324VDT LM324N LM2903DR Texas Instruments operational amplifier op-amp quad op-amp amplifier IC linear IC SOIC-14 surface mount gain-bandwidth product slew rate input offset voltage input bias current single-supply operation push-pull output internal frequency compensation automotive electronics industrial control systems transducer amplifier
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ