Texas Instruments

LM2902KVQDRG4Q1 - Quad 30V 1.2MHz Op Amp, AEC-Q100 | Texas Instruments

MPN: LM2902KVQDRG4Q1 ✓ چالاک
5 V to 30 V Vdss 0.5 uA class Id SOIC-14 (PDSO14), MS-012AB Package
MOQ: 1 |

LM2902KVQDRG4Q1 گشتی

The Texas Instruments LM2902KVQDRG4Q1 is a quadruple general-purpose operational amplifier designed for 30 V supply operation, delivering a 1.2 MHz gain-bandwidth product, a 0.5 V/us slew rate and 80 dB common-mode rejection, packaged in a 14-pin SOIC (PDSO14, MS-012AB) body and qualified to AEC-Q100 for automotive applications.

An operational amplifier, or op amp, is a voltage-gain building block that compares two input terminals and drives its output to amplify the difference between them. A quad op amp such as the LM2902KVQDRG4Q1 integrates four independent amplifier channels in one package. In the product taxonomy it sits at the bottom of the chain: quad operational amplifier -> operational amplifier -> voltage amplifier -> analog amplifier IC -> integrated circuit -> semiconductor. Because the four channels share one package, the LM2902KVQDRG4Q1 replaces four discrete single amplifiers and simplifies both BOM cost and board routing.

Key features include a maximum input offset voltage of 10,000 uV (10 mV), 1.2 MHz unity-gain bandwidth, 0.5 V/us slew rate, 80 dB CMRR and an input bias current in the 0.5 uA class. The device operates from a 5 V minimum supply up to the 30 V class, so it accepts both conventional 5 V logic-era rails and industrial or automotive 24 V buses. Extended temperature performance reaches -55 C to +125 C, and the plastic body is marked as green (lead-free). Improved ESD handling adds robustness: the device withstands less than 500 V per MIL-STD-883, Method 3015 and exceeds 200 V using the machine model.

Architecturally, the LM2902KVQDRG4Q1 uses a classic voltage-feedback differential input stage with a class-AB complementary output stage, which is why the output can swing close to the supply rails without the crossover distortion of a rail-to-rail design. It is intended for single-supply operation from 5 V up, so output swing limits and input common-mode range should be checked against the actual rail. Noise, offset and CMRR figures are specified over the full -55 C to +125 C range rather than only at room temperature, which matters in automotive and industrial environments.

Typical applications include automotive sensor and body electronics signal conditioning, industrial 24 V control panel interface circuits, audio preamplifier and mixer stages, current-loop instrumentation, power-supply feedback loops and general-purpose buffer and gain stages where four channels are needed on a single board.

When designing around this amplifier, remember that it is not rail-to-rail input or output. Keep input common-mode voltage inside the specified range, verify the output swing at the lowest supply voltage you use, and place 100 nF ceramic decoupling close to the V+ and V- pins to avoid supply-noise coupling into the gain stage.

This page brings together the manufacturer specifications, AEC-Q100 and ESD details, pin-level function mapping, drop-in alternatives in the same SOIC-14 footprint, and practical decoupling and thermal guidance that are not consolidated in a single manufacturer datasheet.

جێگرەوەکانی جێگۆڕکێ بۆ LM2902KVQDRG4Q1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902KVQDRG4Q1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature Range, Maximum Supply Voltage, Amplifier Type, Package, Slew Rate.

Texas Instruments
Maximum Supply Voltage: 26 V
Package: 14-SOIC
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →
Texas Instruments
Operating Temperature Range: -55°C to 125°C
Maximum Supply Voltage: 26 V
Slew Rate: 0.5 V/µs
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →
Texas Instruments
Operating Temperature Range: -55 C to +125 C
Maximum Supply Voltage: 30 V
Amplifier Type: General-purpose operational amplifier
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →
Texas Instruments
Operating Temperature Range: -40 °C to +125 °C
Maximum Supply Voltage: 26 V
Amplifier Type: General-purpose operational amplifier
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →
Texas Instruments
Operating Temperature Range: -40°C to 125°C
Maximum Supply Voltage: 30 V
Amplifier Type: Quad general-purpose operational amplifier
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →
onsemi
Maximum Supply Voltage: 32 V
Amplifier Type: General-purpose operational amplifier
Package: 14-SOIC
بەراوردکردن لەگەڵ LM2902KVQDRG4Q1 →

LM2902KAVQDRG4Q1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14 (PDSO14)
4 circuits · 26 V · 5 V · 1.2 MHz · 2 mV · 80 dB · 0.5 V/µs · -55°C to 125°C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902KAVQDRQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14 (PDSO14)
4 circuits · 30 V · 1.2 MHz · 2 mV · 0.5 V/us · 20 nA · 80 dB · 2 kV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14 (PDSO14)
Quad operational amplifier · 4 · 26 V · 1.2 MHz · 2 mV · Single supply or split supply · Push-pull

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902VDR2G

✅ جێگرەوەی ڕاستەوخۆ
onsemi
📦 SOIC-14 (PDSO14)
General-purpose operational amplifier · 4 channels · 3.0 V to 32 V · 32 V · 0.6 V/us typical · Differential input · Single supply · 14-SOIC

پەیوەندی بۆ نرخ

LM2902KVQPWR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14 (PDSO14)
Quad general-purpose operational amplifier · 4 circuits · 30 V · 1.2 MHz · 2 kV · -40°C to 125°C · 14-pin TSSOP (PW) · 14 pins

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902KD

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14 (PDSO14)
4 circuits · General-purpose operational amplifier · 26 V · 1.2 MHz · 2 kV · 3 mV · 2 nA · 0.8 mA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902B

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14 (PDSO14)
Next-generation LM2902B with 36 V supply capability and drop-in replacement for LM224/LM324/LM2902 versions; pin-compatible in SOIC-14

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2902KVQDRG4Q1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 4 channels
Amplifier Type Quad, general-purpose, voltage-feedback operational amplifier
Supply Voltage Range 5 V to 30 V
Unity Gain Bandwidth 1.2 MHz
Slew Rate 0.5 V/us
Input Offset Voltage (max) 10,000 uV (10 mV)
Common-Mode Rejection Ratio (CMRR) 80 dB
Input Bias Current (IBIAS) 0.5 uA class
مەودای پلەی گەرمیی کارکردن -55 C to +125 C (-67 F to +257 F)
Package Type SOIC-14 (PDSO14), MS-012AB
ژمارەی پینەکان 14
جۆری دامەزراندن Surface mount
ESD - HBM Less than 500 V per MIL-STD-883, Method 3015
ESD - Machine Model Exceeds 200 V (200 pF, 1500 ohm)
Automotive Qualification AEC-Q100 qualified
Body Material / Finish Green (lead-free) plastic

ڕێکخستنی پینی LM2902KVQDRG4Q1

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 OUT1 — Channel 1 output
پین 2 -IN1 — Channel 1 inverting input
پین 3 +IN1 — Channel 1 non-inverting input
پین 4 V+ — Positive supply voltage
پین 5 +IN2 — Channel 2 non-inverting input
پین 6 -IN2 — Channel 2 inverting input
پین 7 OUT2 — Channel 2 output
پین 8 OUT3 — Channel 3 output
پین 9 -IN3 — Channel 3 inverting input
پین 10 +IN3 — Channel 3 non-inverting input
پین 11 V- — Negative supply voltage (ground in single-supply use)
پین 12 +IN4 — Channel 4 non-inverting input
پین 13 -IN4 — Channel 4 inverting input
پین 14 OUT4 — Channel 4 output

بەکارهێنانە باوەکان

LM2902KVQDRG4Q1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Industrial 24 V Control Panel Interface, Audio Preamplifier and Mixer Stages, Power Supply Feedback and Voltage Monitoring, Data Acquisition and Instrumentation Buffering, Motor and Actuator Driver Support Circuits.

🚗

Automotive Sensor Signal Conditioning

The LM2902KVQDRG4Q1 is AEC-Q100 qualified, rated from -55 C to +125 C and hardened for ESD at less than 500 V per MIL-STD-883, Method 3015, which makes its four channels well suited to conditioning resistive or current-based sensors in body and chassis electronics. The 30 V supply class tolerates 12 V and 24 V automotive rails with transient headroom, while 80 dB CMRR helps reject the common-mode noise picked up along long harness wiring. Placing the device close to the sensor connector keeps the high-impedance node short, and the quad configuration allows four channels to be conditioned with a single package and one set of bypass capacitors.

🏭

Industrial 24 V Control Panel Interface

In 24 V industrial control cabinets, the LM2902KVQDRG4Q1 operates from a supply well above the nominal bus voltage, leaving margin for inductive spikes on the rail. Its four channels are used for scaling 4-20 mA current-loop inputs, buffering PLC logic levels, driving relay-driver bases and conditioning switch positions. The -55 C to +125 C rating covers unheated enclosures and industrial temperature extremes, and the 1.2 MHz bandwidth is more than adequate for slow process signals where noise rejection and offset stability matter more than speed. The 14-pin SOIC footprint is easy to hand-solder or auto-place on a mixed-signal control board alongside isolation and protection parts.

🎧

Audio Preamplifier and Mixer Stages

The LM2902KVQDRG4Q1 is routinely used in low-cost audio mixer and preamplifier boards because four channels in one SOIC-14 allow a whole stereo/mono mixer to be built from a single IC. The 0.5 V/us slew rate cleanly handles full-scale audio line signals without slew-induced distortion, and the 10 mV maximum input offset keeps DC wander out of the output stage. Because the device is not rail-to-rail, the supply headroom must be checked so that the output swing stays within range on single-supply boards. Adding 100 nF ceramic decoupling on pins 4 and 11 keeps supply noise from modulating the audible floor.

⚡

Power Supply Feedback and Voltage Monitoring

The four channels of the LM2902KVQDRG4Q1 can supervise and protect up to four rails in a power supply or battery-backed system. Two channels can be used as error amplifiers in a feedback loop, while others sense output overvoltage, undervoltage and current-share signals. The 30 V supply class allows direct sensing of 24 V rails without scaling, and the 80 dB CMRR helps maintain regulation when the sensed node sits near noisy switching nodes. Because this is a voltage-feedback design with a 1.2 MHz bandwidth, compensation must be chosen carefully for stability in a switching-regulator feedback loop.

📈

Data Acquisition and Instrumentation Buffering

In instrumentation and data acquisition modules, the LM2902KVQDRG4Q1 provides input buffering and gain stages ahead of an ADC, holding the source impedance low so that the converter settles correctly. The 1.2 MHz bandwidth supports signal bandwidths up to a few hundred kilohertz with moderate closed-loop gain, and the 10 mV maximum offset is small relative to typical millivolt-level sensor outputs. Four channels map naturally onto a four-wire transducer or a multi-channel thermocouple board. Placing the amplifier at the connector, with a 100 nF bypass on each supply pin, minimizes the trace length over which common-mode noise and ESD events are coupled into the signal.

🏗

Motor and Actuator Driver Support Circuits

The LM2902KVQDRG4Q1 is well suited to the small-signal control blocks that surround motor and actuator drivers, such as current-sense amplifiers, cross-over detectors and PWM comparators. The wide 5 V to 30 V supply range allows the sensing circuitry to share the actuator supply rail, and the -55 C to +125 C rating matches the thermal environment near motors and gearboxes. Its 0.5 V/us slew rate responds quickly enough to limit current overshoot in fast current loops. In motor environments, the enhanced ESD ratings reduce the risk of damage from switching transients, but external clamping and filtering are still recommended at the connector.

کورتەی بەرهەمە پێشنیارکراوەکان

MC3403DR Texas Instruments بەکارهێنراوە لە: Automotive Sensor Signal Conditioning TS974IDT STMicroelectronics بەکارهێنراوە لە: Automotive Sensor Signal Conditioning, Data Acquisition and Instrumentation Buffering MC3486NSR Texas Instruments بەکارهێنراوە لە: Automotive Sensor Signal Conditioning MC74F243M onsemi بەکارهێنراوە لە: Industrial 24 V Control Panel Interface, Data Acquisition and Instrumentation Buffering, Motor and Actuator Driver Support Circuits AK5383VS TI بەکارهێنراوە لە: Industrial 24 V Control Panel Interface, Data Acquisition and Instrumentation Buffering TS952IPT STMicroelectronics بەکارهێنراوە لە: Industrial 24 V Control Panel Interface AK4495EQ AKM (Asahi Kasei Microdevices) بەکارهێنراوە لە: Audio Preamplifier and Mixer Stages AK7755EN AKM (Asahi Kasei Microdevices) بەکارهێنراوە لە: Audio Preamplifier and Mixer Stages WM8985CGEFL Cirrus Logic Inc. بەکارهێنراوە لە: Audio Preamplifier and Mixer Stages MC33215BE NXP Semiconductors بەکارهێنراوە لە: Power Supply Feedback and Voltage Monitoring AK4490EN AKM (Asahi Kasei Microdevices) بەکارهێنراوە لە: Power Supply Feedback and Voltage Monitoring TS321IDR Texas Instruments بەکارهێنراوە لە: Power Supply Feedback and Voltage Monitoring MC3487NSR Texas Instruments بەکارهێنراوە لە: Motor and Actuator Driver Support Circuits TS921IPT STMicroelectronics بەکارهێنراوە لە: Motor and Actuator Driver Support Circuits
What is the LM2902KVQDRG4Q1?
The LM2902KVQDRG4Q1 is a Texas Instruments quadruple general-purpose operational amplifier that combines four independent amplifier channels in a single 14-pin SOIC (PDSO14) package. It supports supply voltages up to the 30 V class, has a 1.2 MHz gain-bandwidth product and a 0.5 V/us slew rate, and is AEC-Q100 qualified for automotive use. It is the quad-channel member of the long-running LM2902 family from National Semiconductor, now supported by Texas Instruments.
What is the operating voltage range of the LM2902KVQDRG4Q1?
The LM2902KVQDRG4Q1 operates from a 5 V minimum supply up to the 30 V supply class. According to the manufacturer product page for the LM2902KV, the device is specified as a quad, 30 V, 1.2 MHz operational amplifier with improved ESD protection, and it can also be powered from a single 5 V rail. This wide range makes the part suitable for both 5 V logic-supply circuits and 12 V or 24 V industrial and automotive rails.
Is the LM2902KVQDRG4Q1 AEC-Q100 qualified for automotive use?
Yes, the LM2902KVQDRG4Q1 is AEC-Q100 qualified for automotive applications. The device also carries a customer-specific configuration control that can be supported along with major-change approval, and it is marked as controlled baseline with one assembly/test site and one fabrication site. The extended -55 C to +125 C temperature range and the enhanced ESD ratings make it suitable for underhood and body electronics signal conditioning.
What is the pinout of the LM2902KVQDRG4Q1?
The LM2902KVQDRG4Q1 uses the standard 14-pin SOIC quad-op-amp pinout: pins 2, 3 and 1 are the inverting input, non-inverting input and output of channel 1; pins 6, 5 and 7 belong to channel 2; pins 9, 10 and 8 belong to channel 3; and pins 13, 12 and 14 belong to channel 4. Pin 4 is the positive supply and pin 11 is the negative supply or ground. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
What are the key specifications of the LM2902KVQDRG4Q1 that engineers should know?
The LM2902KVQDRG4Q1 combines a 1.2 MHz unity-gain bandwidth, a 0.5 V/us slew rate, a maximum input offset voltage of 10,000 uV, 80 dB of common-mode rejection and a 0.5 uA class input bias current. It runs from 5 V to the 30 V class, is qualified from -55 C to +125 C, is built in a 14-pin SOIC (PDSO14, MS-012AB) package, and carries AEC-Q100 automotive qualification with enhanced ESD protection of less than 500 V per MIL-STD-883, Method 3015.
What is the difference between the LM2902KVQDRG4Q1 and the LM2902DR?
Both are 14-pin SOIC quad operational amplifiers from the same family, but they carry different qualification and grading. The LM2902DR is the standard commercial-grade ordering option, while the LM2902KVQDRG4Q1 is the AEC-Q100 automotive-qualified, green, -55 C to +125 C version. Both share the same 1.2 MHz bandwidth class, 30 V supply class and pin arrangement, so the qualified part can replace the standard part on the same footprint when automotive screening is required.
Can the LM2902KAVQDRG4Q1 replace the LM2902KVQDRG4Q1?
Yes, the LM2902KAVQDRG4Q1 is listed as a complete replacement for the LM2902KVQDRG4Q1, with consistent terminals, package and functional characteristics. Both are 14-pin Texas Instruments quad operational amplifiers with a 1.2 MHz bandwidth and a 0.5 V/us slew rate in the same SOIC-14 footprint. The A-grade parts are typically screened for tighter offset voltage than the K-grade family, so confirm your offset requirement before treating them as interchangeable in precision loops.
What is the best onsemi equivalent for the LM2902KVQDRG4Q1?
The onsemi LM2902VDR2G is a 14-pin SOIC quad operational amplifier that is a drop-in footprint match for the LM2902KVQDRG4Q1, with the same pin arrangement and the same 1.2 MHz bandwidth, 0.5 V/us slew rate and 30 V supply class. It is a practical cross-brand alternative when you need a second source, although you should verify the temperature grade, ESD rating and AEC-Q100 qualification level against your own requirements before releasing the design to production.
When should I choose the LM2902KVQDRG4Q1 over a single-channel amplifier?
Choose the LM2902KVQDRG4Q1 when your circuit needs three or four amplifiers and they can share one package. It consolidates four amplifiers into a single 14-pin SOIC, which reduces board area, supply routing and part count versus four discrete single amplifiers. Choose a single-channel device instead when the channels are physically separated, when you need rail-to-rail input or output capability that this voltage-feedback part does not offer, or when the design requires a wide common-mode range near the rails.
Is the LM2902KVQDRG4Q1 suitable for 24 V industrial control applications?
Yes, the LM2902KVQDRG4Q1 is suitable for 24 V industrial control applications because it supports supply voltages in the 30 V class, giving adequate headroom above a 24 V bus for transient margin. Its 80 dB CMRR helps reject common-mode noise coupled into long sensor wiring, and the extended -55 C to +125 C range covers industrial temperature spans. Confirm the input common-mode range and output swing against your actual rail before finalizing the front end.
What can replace the LM2902KVQDRG4Q1?
Direct replacements include the same-family Texas Instruments parts LM2902KAVQDRG4Q1, LM2902KAVQDRQ1 and LM2902DR, all of which use the identical 14-pin SOIC footprint with the same 1.2 MHz bandwidth, 0.5 V/us slew rate and 30 V supply class. The onsemi LM2902VDR2G is a cross-brand drop-in option. Every candidate must be checked for automotive qualification, ESD rating and temperature grade before substitution.
Where to download the LM2902KVQDRG4Q1 datasheet PDF?
The manufacturer datasheet PDF for the LM2902KVQDRG4Q1 is available from Texas Instruments at the LM2902KV product page on ti.com, and the automotive-qualified LM2902-Q1 datasheet is linked from that family page. Use the pin-description table and the Electrical Characteristics table in that document for the final design sign-off, since ordering-option and grade details differ between the LM2902K, LM2902KV and LM2902-Q1 variants.
Does the LM2902KVQDRG4Q1 need decoupling capacitors?
Yes, the LM2902KVQDRG4Q1 needs supply decoupling for stable, low-noise operation. Place a 100 nF ceramic capacitor as close as practical to the V+ pin (pin 4) and the V- or ground pin (pin 11), with the shortest possible ground return path. If the amplifier sits far from the supply source, add bulk capacitance of a few microfarads close to the device to supply the transient current drawn by the output stage during slewing.
Is the LM2902KVQDRG4Q1 rail-to-rail?
No, the LM2902KVQDRG4Q1 is not a rail-to-rail input or output amplifier. It uses a conventional voltage-feedback topology whose input common-mode range and output swing are limited relative to the supply rails, so the input signal must stay inside the specified common-mode window and the output must stay within the achievable swing. If your signal can reach the rails, or if you need a common-mode range extending to ground on a single 5 V supply, specify a rail-to-rail amplifier instead.
Where can I buy the LM2902KVQDRG4Q1 and what is the lead time?
You can request a quote for the LM2902KVQDRG4Q1 using the Request a Quote form on this page, which covers pricing, stock confirmation and lead time for the SOIC-14 automotive-qualified ordering option. The part ships in a standard 14-pin SOIC surface-mount package and is offered in tape-and-reel quantities suitable for production assembly; the manufacturer lists the device as an active product.

داتای سەرچاوەی ئەندازیاری بۆ LM2902KVQDRG4Q1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2902KVQDRG4Q1 when you need four general-purpose amplifier channels in a 14-pin SOIC, a supply in the 30 V class, and AEC-Q100 automotive qualification with extended -55 C to +125 C operation. Choose the LM2902KAVQDRG4Q1 when you want the same footprint and identical 1.2 MHz bandwidth but prefer the A-grade offset screening; it is listed as a complete replacement. Choose LM2902DR for commercial-grade industrial designs where automotive screening is unnecessary. Choose the onsemi LM2902VDR2G when a cross-brand second source matters, re-verifying temperature grade and ESD rating. Choose LM2902B if you need the higher 36 V supply class of the next-generation part. Do not choose any of these if your design requires rail-to-rail input or output operation, a common-mode range reaching the rails, or offset accuracy tighter than the 10 mV maximum of this family.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2902KAVQDRG4Q1 LM2902KAVQDRQ1 LM2902DR LM2902VDR2G LM2902B
Package SOIC-14 (PDSO14), MS-012AB SOIC-14 (PDSO14) - same SOIC-14 (PDSO14) - same SOIC-14 (PDSO14) - same SOIC-14 (PDSO14) - same SOIC-14 (PDSO14) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments onsemi Texas Instruments
Number of Amplifiers 4 4 4 4 4 4
Supply Voltage Range 5 V to 30 V class 5 V to 30 V class 5 V to 30 V class 5 V to 30 V class 5 V to 30 V class Up to 36 V class
Gain-Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz
Slew Rate 0.5 V/us 0.5 V/us 0.5 V/us 0.5 V/us 0.5 V/us 0.5 V/us

جیاکەرەوە سەرەکییەکان

  • Automotive-qualified grade in a standard 14-pin SOIC without a footprint change (بەراورد بەLM2902DR)
  • Directly listed as a complete replacement with identical terminals and package (بەراورد بەLM2902KAVQDRG4Q1)
  • Second-source flexibility with a genuine cross-brand drop-in option (بەراورد بەLM2902VDR2G)
  • Improved ESD robustness over legacy LM2902 versions (بەراورد بەLM2902B)

تێبینییەکانی دیزاین

The LM2902KVQDRG4Q1 is a class-AB voltage-feedback amplifier, so the supply pins still draw current dynamically as the output swings. Place a 100 nF ceramic bypass capacitor directly at pin 4 (V+) and pin 11 (V-) with the shortest possible ground return, and add 1 uF to 10 uF of bulk capacitance near the device when the amplifier is driven by a fast load step. On a single 5 V supply, tie V- to ground at the device and keep the return current out of the analog ground path of any ADC reference.

Keep the four channels' feedback networks close to their pins. A standard non-inverting stage places the feedback divider between pins 1 (or 7, 8, 14) and the inverting input, and routing these nets over the device body couples output into input. For the inverting configuration, use the non-inverting pin as the reference and keep that reference node on a low-impedance, quiet return rather than a shared analog ground plane carrying motor or switching currents.

This amplifier is not rail-to-rail on either input or output, so two checks catch most field failures. First, confirm that the signal common-mode voltage stays inside the specified input range for the lowest supply voltage in your system, especially on 5 V single-supply designs where an input near 0 V can saturate the input stage. Second, verify that the required output amplitude fits within the achievable swing; at 5 V supply and light load the usable output range is well below the rails.

Do not substitute this part into a design that expects a rail-to-rail amplifier, and do not use it in a high-gain precision DC amplifier without checking the offset contribution. The maximum input offset voltage of 10 mV at the highest temperature, combined with 80 dB CMRR, is adequate for audio, industrial signal conditioning and general buffering, but a precision instrumentation loop may need a trimmed or low-offset amplifier instead. The 1.2 MHz bandwidth also means noise gain must be kept low at low frequencies for stable operation.

Estimated: with a 30 V maximum supply and a 24 V rail, the maximum power dissipation in the output stage is bounded by the output swing times the load current, since the class-AB bias current is small. In a 14-pin SOIC with no exposed pad, keep continuous load current well below the point where the die temperature rise becomes significant; use a modest output load (tens of milliamperes into high impedance or a few milliamperes into a low-impedance load) and, if more current is required, drive the load through an external transistor rather than the amplifier output.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The device is AEC-Q100 qualified for automotive applications and the body is described as green plastic (lead-free). ESD capability is specified as less than 500 V per MIL-STD-883, Method 3015 and more than 200 V using the machine model. RoHS and REACH status were not stated for this ordering option.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2902KVQDRG4Q1 LM2902KVQDRG4Q1 datasheet LM2902KVQDRG4Q1 datasheet pdf LM2902KVQDRG4Q1 pinout LM2902KVQDRG4Q1 equivalent LM2902KVQDRG4Q1 drop-in replacement LM2902KVQDRG4Q1 vs LM2902DR LM2902KVQDRG4Q1 vs LM2902KAVQDRG4Q1 Texas Instruments LM2902KVQDRG4Q1 LM2902KVQDRG4Q1 SOIC-14 quad op amp LM2902KVQDRG4Q1 price LM2902KVQDRG4Q1 stock AEC-Q100 quad operational amplifier 30V LM2902KVQDRG4Q1 automotive sensor signal conditioning LM2902KVQDRG4Q1 footprint and pin functions

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments National Semiconductor LM2902KVQDRG4Q1 LM2902KAVQDRG4Q1 LM2902KAVQDRQ1 LM2902DR LM2902B onsemi LM2902VDR2G quad operational amplifier operational amplifier voltage amplifier analog amplifier IC integrated circuit semiconductor voltage-feedback topology class-AB output stage gain-bandwidth product slew rate common-mode rejection ratio (CMRR) input offset voltage AEC-Q100 RoHS REACH MIL-STD-883 SOIC-14 PDSO14 MS-012AB surface mount automotive electronics industrial control signal conditioning
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ