onsemi

LM2902VN - Quad Low-Power Op-Amp, 3-32V | onsemi

MPN: LM2902VN ✓ چالاک
3 V to 32 V Vdss 0.5 uA Id PDIP-14 (0.300 in, 7.62 mm) Package
MOQ: 1 |

LM2902VN گشتی

The onsemi LM2902VN is a single-supply quad operational amplifier with four independent, internally frequency-compensated, high-gain amplifier stages in a 14-pin PDIP (0.300 in, 7.62 mm pitch) through-hole package. It operates from a single supply of 3V to 32V (the manufacturer also markets a 3-26V variant rating) or dual supplies of ±1.5V to ±16V, and delivers a high open-loop gain of approximately 70 dB with very low input bias current around 0.5 uA per input.

A quad operational amplifier is an analog signal-conditioning IC that integrates four identical op-amp cores on one silicon die, sharing a common power supply while keeping the signal paths independent. Within the amplifier hierarchy it belongs to the general-purpose operational amplifier class, sitting under linear amplifiers, which in turn sit under analog integrated circuits and signal-chain components in a power management and signal conditioning system.

Key features include true differential inputs that remain linear with input common-mode voltage extending to ground (negative rail) on single supplies, output voltage swing that approaches ground for loads referenced to ground, and low quiescent current that scales with supply rather than with load, making it attractive for battery-operated equipment. Internally compensated frequency response gives unity-gain stability without external components.

Architecturally, the LM2902 family follows the classic LM324 bipolar process: a PNP differential input stage enables ground-sensing inputs, and a Darlington-pair output stage provides moderate source and sink capability. This mature process yields a robust, low-cost part with wide availability and proven field reliability.

Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators in non-critical timing roles, industrial sensor front ends, and automotive subsystems where the extended supply range covers vehicle transients.

A key design consideration: the output stage can sink only limited current near ground (typically tens of microamps below ~0.1V), so a pull-down resistor to ground is recommended when a single-supply design requires the output to reach 0V.

This page adds value beyond the datasheet by consolidating drop-in replacement options, package and pinout details, application guidance, and sourcing information in one AI-citable reference.

جێگرەوەکانی جێگۆڕکێ بۆ LM2902VN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902VN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Mounting Type, Amplifier Type, Package, Architecture, Gain-Bandwidth Product.

Texas Instruments
Mounting Type: Through-hole
Amplifier Type: Quad general-purpose operational amplifier
Architecture: Independent, high-gain, internally frequency-compensated
بەراوردکردن لەگەڵ LM2902VN →
Texas Instruments
Mounting Type: Surface mount
Amplifier Type: General-purpose operational amplifier
Package: 14-SO
بەراوردکردن لەگەڵ LM2902VN →
Texas Instruments
Mounting Type: Through-hole
Package: 14-pin PDIP
Architecture: High-gain, internally frequency-compensated amplifiers
بەراوردکردن لەگەڵ LM2902VN →

LM2902N

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 PDIP-14
4 · 26 V · 1 MHz · Quad general-purpose operational amplifier · Independent, high-gain, internally frequency-compensated · Single-supply operation · 14-pin DIP · DIP-14

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324N

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 PDIP-14
4 independent amplifiers · Low-power quad operational amplifier · Standard general-purpose amplifier · High-gain, internally frequency-compensated amplifiers · Single-supply capable

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-14
4 · 26 V · 1 MHz · Quad general-purpose operational amplifier · Independent, high-gain, internally frequency-compensated · Single-supply operation · 14-pin DIP · DIP-14

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-14
4 independent amplifiers · Low-power quad operational amplifier · Standard general-purpose amplifier · High-gain, internally frequency-compensated amplifiers · Single-supply capable

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-14
4 independent amplifiers · Low-power quad operational amplifier · Standard general-purpose amplifier · High-gain, internally frequency-compensated amplifiers · Single-supply capable

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902VN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Configuration Quad (4 independent amplifiers)
Amplifier Type General-purpose, single-supply operational amplifier
Supply Voltage Range (single) 3 V to 32 V
Supply Voltage Range (dual) ±1.5 V to ±16 V
Supply Voltage (alternate listing) 3 V to 26 V
Open-Loop Voltage Gain 70 dB
Input Bias Current 0.5 uA
Input Common-Mode Range Includes negative rail (ground-sensing inputs)
ژمارەی پینەکان 14
پاکێج PDIP-14 (0.300 in, 7.62 mm)
جۆری دامەزراندن Through Hole

ڕێکخستنی پینی LM2902VN

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 VCC — Positive supply voltage
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 OUT3 — Output of amplifier 3
پین 9 IN3- — Inverting input of amplifier 3
پین 10 IN3+ — Non-inverting input of amplifier 3
پین 11 GND/VEE — Ground or negative supply
پین 12 IN4+ — Non-inverting input of amplifier 4
پین 13 IN4- — Inverting input of amplifier 4
پین 14 OUT4 — Output of amplifier 4

بەکارهێنانە باوەکان

LM2902VN گونجاوە بۆ 6 بەکارھێنانs: Transducer Amplifier Front Ends, DC Gain Blocks, Active Filters, Automotive Signal Conditioning, Battery-Powered Portable Equipment, Comparator and Threshold Detection Circuits.

🏭

Transducer Amplifier Front Ends

The LM2902VN is a classic choice for amplifying low-level signals from pressure, temperature, and light sensors in industrial and automotive systems. Its PNP input stage senses signals at ground potential, so ground-referenced transducer outputs can be amplified directly on a single supply without level-shifting circuitry. With a high open-loop gain of 70 dB and input bias current of only 0.5 uA, it preserves signal fidelity from high-impedance sources. Because one package provides four amplifiers, multi-channel sensor boards use fewer components. The 3V-32V supply range tolerates unregulated industrial and automotive rails, though designers should add local decoupling and account for the limited output sink current near 0V when conditioning low-side signals.

🔧

DC Gain Blocks

As a DC gain block, the LM2902VN provides stable, predictable gain with only external resistors setting the transfer function. The internally compensated design is unity-gain stable, so non-inverting and inverting configurations work without external compensation capacitors. With a supply span of 3V to 32V, gain blocks can operate from 5V logic rails or 24V industrial buses using the same PCB design. Input bias current of 0.5 uA permits resistor values up to the hundreds-of-kilohms range without significant offset error. Designers should bias the reference node near mid-supply for AC-coupled signals and remember that output swing approaches, but does not exactly reach, the negative rail under load, so gain-block headroom should be budgeted accordingly in precision DC designs.

🔧

Active Filters

The LM2902VN implements multiple-pole Sallen-Key and multiple-feedback active filters efficiently, since four amplifier stages in one 14-pin package support cascaded filter sections without extra ICs. Its unity-gain stability ensures the popular unity-gain Sallen-Key topology works reliably, and the 70 dB open-loop gain keeps the actual filter response close to the ideal transfer function at audio and low-instrumentation frequencies. Single-supply operation requires biasing the filter ground reference to a mid-supply virtual ground generated by a resistor divider, buffered by one of the four internal amplifiers. For frequencies well above the low hundreds of kilohertz, the limited gain-bandwidth of this low-power family introduces response droop, so modern faster amplifiers are preferable for high-frequency filter designs.

🚗

Automotive Signal Conditioning

The LM2902 'V' family is specified for the extended temperature ranges demanded by automotive electronics, and the 3V-32V supply range accommodates the wide voltage excursions of a 12V vehicle electrical system when paired with transient suppression. Typical automotive uses include battery-voltage monitoring dividers, throttle and pedal-position sensor amplification, coolant-temperature signal conditioning, and dashboard indicator comparators. The ground-sensing input architecture simplifies interfacing with chassis-referenced sensors, and the quad integration reduces component count on cost-sensitive body-control boards. Designers must add series input resistance and clamp protection for load-dump conditions, and should verify that output sink requirements near 0V, such as low-side indicator drives, include the recommended pull-down resistance for correct low-level switching.

📱

Battery-Powered Portable Equipment

The low-power characteristic of the LM2902VN family, in which supply current is set by the design rather than the load, makes it suitable for battery-operated instrumentation, multimeters, and portable sensor units. Operating from a single 3V supply at the low end, it works directly from two alkaline cells or a single lithium cell through a regulator. Input bias current of 0.5 uA minimizes loading on high-impedance sensor sources, preserving battery life indirectly by allowing larger source resistances. Four amplifiers per package reduce board space and assembly cost in portable designs. For ultra-long-battery-life products, engineers should compare quiescent drain against newer CMOS op-amps, which can cut supply current by an order of magnitude at the cost of supply-voltage range.

⚡

Comparator and Threshold Detection Circuits

In non-critical timing applications, one or more LM2902VN amplifiers can be wired open-loop as comparators for threshold detection, over-voltage flags, and simple level indication. The ground-sensing input range allows comparison of ground-referenced signals against a divider-derived threshold on a single supply. Open-loop gain of 70 dB yields clearly saturated high/low outputs for tens-of-millivolts differentials. However, this family is not specified for comparator propagation speed or hysteresis behavior, so designers must add positive-feedback resistors for hysteresis and must not rely on it for fast edge detection; a dedicated comparator is recommended when response time or speed matters. For slow alarms and supervisory flags, the LM2902VN remains a cost-effective multi-channel solution.

هیچ پرسیارێکی باو بۆ ئەم بەرهەمە بەردەست نییە.

داتای سەرچاوەی ئەندازیاری بۆ LM2902VN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the onsemi LM2902VN when you need a through-hole quad op-amp with ground-sensing inputs, a wide 3V-32V single-supply range, and extended-temperature (V-family) qualification - typical for automotive signal conditioning, industrial sensor front ends, and DC gain blocks on 24V buses. Choose the onsemi or TI LM324N if your product is consumer-grade only and commercial temperature qualification suffices, often at slightly lower cost. Choose the TI LM2902N for an identical extended-grade part from an alternate manufacturer when dual-sourcing. If your application instead demands rail-to-rail output at 0V under load, higher bandwidth, or microvolt offset precision, step up to a modern rail-to-rail amplifier rather than working around the LM2902VN output-stage limits. All listed alternatives share the same PDIP-14 footprint, so qualification requires no PCB change.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2902N (onsemi) LM324N (onsemi) LM2902N (TI) LM324N (TI)
Package PDIP-14 (7.62 mm) PDIP-14 - same PDIP-14 - same PDIP-14 - same PDIP-14 - same
Brand onsemi onsemi onsemi Texas Instruments Texas Instruments
Number of Amplifiers 4 4 4 4 4
Supply Voltage Range 3 V to 32 V 3 V to 32 V 3 V to 32 V 3 V to 32 V 3 V to 32 V
Open-Loop Gain 70 dB 70 dB 70 dB 70 dB 70 dB
Temperature Grade Extended (V suffix) Extended (V family) Commercial Extended (V family) Commercial
Mounting Type Through Hole Through Hole Through Hole Through Hole Through Hole

جیاکەرەوە سەرەکییەکان

  • Extended automotive temperature grade (بەراورد بەLM324N (onsemi))
  • Ground-sensing inputs on single supply (بەراورد بەModern rail-to-rail quad op-amps)
  • Four channels per 14-pin package (بەراورد بەTS321IDR single op-amp)

تێبینییەکانی دیزاین

The most common LM2902VN design error is assuming rail-to-rail output swing on a single supply. The output can source well toward VCC but sinks only tens of microamps when the output is below roughly 0.1V. If your circuit requires the output to reach 0V under load (for example, driving a logic input or an ADC near its zero-code), add a pull-down resistor of a few kilohms from the output to ground, or provide a small negative rail. Verify the exact sink-current curve in the onsemi datasheet for your load resistance.

Place a 0.1 uF ceramic decoupling capacitor directly across pins 4 (VCC) and 11 (GND/VEE) of the LM2902VN, with a low-impedance ground return. On through-hole PDIP layouts, keep the ground node common to all four amplifier reference networks; ground bounce between amplifier sections is the usual cause of crosstalk in quad op-amp boards. Keep high-impedance input traces (2, 3, 5, 6, 9, 10, 12, 13) short and guarded by ground pours to limit leakage with the 0.5 uA bias current.

Estimated: with a 24V single supply and ~1 mA total quiescent draw typical of this low-power family, package dissipation is about 24 mW before load current, comfortably within PDIP thermal limits. However, load current drawn continuously from an amplifier output flows through the die; at 24V supply and a 20 mA output load, dissipation rises to roughly 0.5 W per package, which a PDIP-14 in still air handles but should be verified against the datasheet power-derating curve at elevated ambient temperature.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status should be confirmed on the official onsemi product page and latest datasheet revision.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm2902 pdf LM2902VN datasheet LM2902VN datasheet pdf LM2902VN pinout LM2902VN equivalent LM2902VN replacement LM2902VN cross reference LM2902VN vs LM324N onsemi LM2902VN LM2902VN price LM2902VN stock LM2902 quad op-amp 14-pin DIP

پێکهاتە و زاراوە پەیوەندیدارەکان

onsemi ON Semiconductor LM2902VN LM2902 LM324 LM2902N LM324N Texas Instruments STMicroelectronics quad operational amplifier operational amplifier amplifier IC single-supply op-amp PDIP-14 DIP package through-hole open-loop gain input bias current input common-mode range transducer amplifier active filter automotive electronics battery-powered instrumentation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ