LM2903PWRG4 - Dual Open-Collector Comparator | TI
MPN: LM2903PWRG4 ✓ چالاکLM2903PWRG4 گشتی
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy, within analog interface ICs and general-purpose semiconductor signal-conditioning devices. Its open-collector transistor output can sink current to a logic-low state while leaving the output node in a high-impedance state when the comparator is inactive. This architecture makes pull-up resistors and compatible pull-up voltage selection important parts of the surrounding circuit.
Key features include two independent comparison channels, rail-to-rail input operation as identified for this device, and a wide supply-voltage range. The 0.37 mV input offset specification helps limit the input differential needed to change an output, while the 3.5 nA bias-current specification reduces disturbance on high-impedance sensing nodes. The 1 us response time is useful for threshold detection, signal conditioning, and control loops that require a defined transition interval.
The device supports single-supply operation and dual-supply operation, giving designers flexibility in industrial, automotive, and embedded systems. Its open-collector outputs can drive multiple pull-up domains when appropriate system-level conditions are met, although each connected node must remain within the device's applicable electrical limits. The 200 uA supply-current value per comparator also makes the part suitable for power-conscious monitoring and control circuits where continuous comparator operation is required.
Typical uses include overvoltage and undervoltage detection, sensor threshold conditioning, industrial control logic, automotive interface circuits, window or level comparison, and general-purpose decision logic. In each case, resistor selection around the open-collector outputs and proper input common-mode limits are central to obtaining predictable operation.
Design with the input common-mode range, supply voltage, output pull-up voltage, and input differential polarity together. Keep sensitive comparison traces short, provide stable bypassing near the supply pins, and account for the open-collector output's rise time, which is influenced by the pull-up resistor and total node capacitance rather than only by the comparator response time.
This page combines manufacturer specifications, packaging details, application guidance, and qualified drop-in comparison information to support faster component selection and PCB implementation. It also highlights the electrical details that distinguish this 8-TSSOP comparator from alternatives with different package or interface requirements.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903PWRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903PWRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Output Type, Input Bias Current, Input Offset Voltage, Response Time.
LM2903PWR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903PWG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903PWRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| جۆری دەرچوون | Open collector |
| Input Characteristics | Rail-to-rail |
| Supply Voltage Range, Single Supply | 2 V to 36 V |
| Maximum Supply Voltage | 38 V |
| Typical Operating Voltage | ±15 V / 30 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| ئێستای دابینکردن | 200 uA per comparator |
| Response Time | 1 us |
| ESD Rating, HBM | 2 kV |
| پاکێج | 8-TSSOP |
| Package Width | 4.40 mm |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی LM2903PWRG4 4.40 mm
ڕێکخستنی پین بۆ LM2903PWRG4 (پاکێجی 4.40 mm). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2903PWRG4.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2903PWRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Overvoltage Detection, Automotive Sensor Threshold Conditioning, Power-Supply Window Monitoring, Battery-Level Detection, Digital Control and Logic Interface, Audio and Communication Signal Level Detection.
Industrial Overvoltage Detection
The LM2903PWRG4 is suitable for detecting when a monitored industrial rail crosses an adjustable threshold. Its 0.37 mV input offset voltage helps the comparator establish a narrow decision boundary, while the 3.5 nA input bias current limits the effect of the sensing divider on a high-impedance node. Each open-collector output can pull a downstream fault or shutdown signal low. Place the divider close to the comparator, bypass the supply pins locally, and account for tolerance and temperature drift when setting the threshold.
پێشنیارکراو
Automotive Sensor Threshold Conditioning
The LM2903PWRG4 can compare a sensor-derived voltage against a reference in automotive interface circuits. Its 1 us response time provides a defined state-change interval, and its 38 V maximum supply rating gives useful margin for 12 V electrical environments when transient protection is present. The low 3.5 nA input bias current helps preserve high-impedance sensor signals. The open-collector output can alert a logic circuit, but its pull-up network must remain compatible with the vehicle's voltage levels.
پێشنیارکراو
Power-Supply Window Monitoring
Two independent LM2903PWRG4 channels can monitor upper and lower limits of a supply rail, creating a voltage-window function with a valid-output indication. The 2 V to 36 V dual-supply span and 38 V maximum rating support broad input ranges, while the 200 uA supply current per comparator reduces the continuous overhead of always-on monitoring. Use resistor-divider inputs with suitable precision, add hysteresis for noise immunity, and pull up each open-collector output to the logic rail used by the supervising circuit.
پێشنیارکراو
Battery-Level Detection
The LM2903PWRG4 can compare a scaled battery voltage with a reference to produce a discrete low-battery event. Its rail-to-rail input characteristic and low input bias current are useful when the sensing divider presents limited loading to the source. The 1 us response time allows rapid threshold transitions, although the open-collector output's rising edge depends on the pull-up resistor and wiring capacitance. Include hysteresis to prevent repeated switching near the threshold and protect the battery input against transients.
پێشنیارکراو
Digital Control and Logic Interface
The LM2903PWRG4 can convert an analog threshold condition into an open-collector digital event for a microcontroller or logic gate. Its 1 us response time supports prompt control-loop participation, while the two independent channels can handle separate decisions or complementary conditions. Because the output transistor actively pulls low and otherwise releases the node, choose a pull-up voltage and resistor that match the receiving logic. Keep the analog input path short and separate from switching-node return currents.
پێشنیارکراو
Audio and Communication Signal Level Detection
The LM2903PWRG4 can detect whether an audio or communications signal exceeds a defined level and then drive an open-collector alarm or control input. The low 3.5 nA bias current reduces loading on a high-impedance detector, and the 0.37 mV offset supports fine threshold placement around the zero crossing. Add controlled hysteresis to avoid chatter, keep the comparator outside strong switching-node fields, and select the output pull-up to suit the receiving audio or communication equipment.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903PWRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903PWR | LM2903PWG4 |
|---|---|---|---|
| Package | TSSOP-8 (PW) | TSSOP-8 (PW) | TSSOP-8 (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open collector | Open collector | Open collector |
جیاکەرەوە سەرەکییەکان
- Two independent channels in a compact 8-TSSOP (بەراورد بەLM2903PWR)
- Low input offset for precise threshold decisions (بەراورد بەLM2903PWG4)
- Wide supply capability with a defined response interval (بەراورد بەLM2903PWR)
تێبینییەکانی دیزاین
Do not treat the 1 us response-time specification as the complete output timing. The open-collector output turns off into a high-impedance state, so the rising edge is also determined by the pull-up resistor, trace capacitance, and input capacitance of the receiving device. Select a pull-up value that establishes the required logic-high voltage while keeping the output-node rise time within the receiving circuit's timing budget.
Place the input-divider components, reference source, and comparator input pins close together to minimize susceptibility to injected noise. Keep the open-collector output routing away from high-energy switching nodes, especially where a pull-up resistor can couple fast edges into the comparison input. Add local supply bypassing and return current directly to the device ground pin to keep supply ripple from disturbing the threshold decision.
Use positive feedback or another controlled hysteresis method when the compared signal can cross the threshold slowly. This prevents output chatter caused by small noise variations near equality. The 0.37 mV offset is only one contributor to the total decision error; resistor tolerance, reference accuracy, input bias current, temperature drift, and propagation delay should also be included when determining the usable threshold margin.
The LM2903PWRG4 has a 38 V maximum supply rating, but that rating is an absolute limit rather than a recommended operating point. Include transient suppression when the monitored source can contain inductive or capacitive energy. Ensure that input voltages, pull-up voltages, and supply combinations remain within the datasheet limits under startup, shutdown, and fault conditions.
زانیاری پابەندبوون
The Texas Instruments product information identifies a 2 kV HBM ESD rating for the B-version family. Separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not identified, so those fields remain unknown.