LM2903QDRG4Q1 - Dual Comparator | Texas Instruments
MPN: LM2903QDRG4Q1 ✓ چالاکLM2903QDRG4Q1 گشتی
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category belongs to the broader amplifier IC and signal-conditioning hierarchy, where open-collector outputs are useful for wired logic, system-level signaling, and driving external pull-up networks. The LM2903-Q1 family combines independent channels with automotive qualification for applications requiring reliable operation across extended temperatures.
Key electrical characteristics include a maximum input-offset voltage of 7 mV at 5 V, a maximum input-bias current of 0.25 µA, typical output current of 20 mA, and maximum quiescent current of 2.5 mA. Its differential architecture supports sensing whether one voltage is above or below another without requiring a feedback network. The open-collector output can sink current while remaining in a high-impedance state when the output transistor is off.
The two channels operate independently, allowing one device to implement two threshold decisions, window-detection functions, or complementary monitoring functions. A supply range extending to 36 V is valuable in automotive and industrial systems where the comparator may be connected to protected battery-derived or higher-voltage signal rails. The low input-bias current helps reduce errors when sensing high-impedance sources, while the specified offset limit establishes the basic threshold-accuracy boundary.
Typical applications include automotive battery and power-rail supervision, sensor threshold detection, overvoltage and undervoltage indication, window comparators, and digital-control interfaces. The open-collector architecture also allows multiple comparators to share a pull-up resistor when wired logic is acceptable. External pull-up selection must account for the required sink current, rise time, bus capacitance, and system-level fault conditions.
Designers should account for input common-mode limits, supply polarity, output pull-up placement, and unused-channel handling. Place the pull-up resistor near the open-collector output or system bus, and verify that the 20 mA typical output-current capability covers the worst-case sink demand. The manufacturer datasheet and pin-description table remain the controlling references for connection, common-mode range, and package details.
This product page combines manufacturer specifications, package information, drop-in replacement guidance, and practical application guidance. It supports faster component selection while preserving the electrical checks required for reliable comparator-based sensing and control systems.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903QDRG4Q1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903QDRG4Q1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature Range, Logic Compatibility, Output Type, Number of Channels.
LM2903QDG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VQDRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903QDRG4Q1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Dual Supply Range | ±1 V to ±18 V |
| جۆری دەرچوون | Open-collector |
| Maximum Input Offset Voltage | 7 mV at 5 V |
| Maximum Input Bias Current | 0.25 µA |
| Typical Output Current | 20 mA |
| Maximum Quiescent Current | 2.5 mA |
| Automotive Qualification | AEC-Q100 Grade 0 and 1 |
| مەودای پلەی گەرمیی کارکردن | -40°C to +125°C |
| پاکێج | 8-SOIC (D), 8 pins |
| Package Width | 3.90 mm |
| Package Length | 0.154 inch |
| جۆری دامەزراندن | Surface mount |
| Single-Supply Operation | 2 V to 36 V |
| Minimum Supply Difference in Dual Operation | 2 V |
| Minimum VCC Margin for Dual-Supply Operation | 1.5 V |
| ESD Qualification | 2 kV ESD performance |
ڕێنمایی ڕێکخستنی پینی LM2903QDRG4Q1 0.154 inch
ڕێکخستنی پین بۆ LM2903QDRG4Q1 (پاکێجی 0.154 inch). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2903QDRG4Q1.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2903QDRG4Q1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Battery Monitoring, Automotive Overvoltage Detection, Sensor Threshold Detection, Power-Supply Sequencing, Window Comparator, Digital Control Interface.
Automotive Battery Monitoring
The LM2903QDRG4Q1 fits automotive battery supervision because it combines a 2 V to 36 V supply range with AEC-Q100 Grade 0 and 1 qualification and operation from -40°C to +125°C. One comparator can compare a divided battery voltage with a precise threshold, while the second channel can monitor a related condition such as regulator enable or charge state. Its maximum input-offset voltage of 7 mV at 5 V defines the basic comparison-accuracy boundary, while the 0.25 µA maximum input-bias current limits error in high-impedance divider networks. The open-collector output can operate as an active-low warning or enable signal. Final design work must verify transient protection, input common-mode limits, pull-up current, and fault behavior throughout the vehicle power environment.
Automotive Overvoltage Detection
The LM2903QDRG4Q1 can implement independent overvoltage and undervoltage thresholds by using its two differential comparator channels. Its 36 V maximum supply rating suits applications that remain connected to protected automotive power rails, while the low 0.25 µA maximum input-bias current helps preserve divider accuracy. A resistive divider can scale a battery or load rail to the comparator input range, and the open-collector outputs can drive pulled-up status inputs or discrete control stages. According to the Texas Instruments LM2903-Q1 documentation, Grade 0 and 1 automotive qualification supports stringent temperature requirements. Designers must still examine common-mode voltage, input protection, output pull-up strength, response time, and system-level false-trip behavior before releasing the circuit for production.
Sensor Threshold Detection
The LM2903QDRG4Q1 is suitable for determining whether a sensor-derived voltage has crossed a defined limit. Its differential inputs accept a sensed signal and a reference, while the 7 mV maximum offset at 5 V provides a defined basis for close-threshold decisions. The 2.5 mA maximum quiescent current is particularly useful in low-power automotive sensing paths, and the 0.25 µA maximum bias current reduces loading on high-impedance sensor networks. One channel can perform threshold detection while the other monitors a complementary condition or supplies a second trip point. Because the outputs are open collector, the circuit requires pull-up resistors and careful routing to avoid excessive bus capacitance or slow rising edges. Reference accuracy and sensor noise often dominate the final threshold error.
Power-Supply Sequencing
The two independent channels of the LM2903QDRG4Q1 can supervise more than one supply threshold in a multi-rail automotive or industrial system. A divided rail voltage can be compared with a reference to produce an open-collector enable request, and the second channel can validate another rail or establish an alternate power-good indication. The wide 2 V to 36 V operating supply range supports low-voltage logic and higher-voltage automotive rails within one device family. Its 20 mA typical output-current capability provides useful pull-up sinking margin, subject to the detailed operating conditions. According to the Texas Instruments product page, the Q1 configuration provides AEC-Q100 Grade 0 and 1 qualification. Sequencing reliability also depends on reference accuracy, hysteresis, delay, and the behavior of external pull-up networks.
Window Comparator
Two LM2903QDRG4Q1 channels can be combined into a window comparator by establishing upper and lower thresholds for a monitored voltage. One channel detects when the input rises above the upper limit, and the other detects when it falls below the lower limit, allowing the open-collector outputs to identify whether the signal is inside or outside its permitted range. The 7 mV maximum input-offset voltage at 5 V is a useful starting point for close comparison windows, although reference tolerance and input-referred noise can widen actual limits. The low 0.25 µA maximum input-bias current helps prevent threshold shifting in resistive dividers. For automotive deployment, the device’s Grade 0 and 1 qualification and -40°C to +125°C rating support harsh conditions, but ESD protection, debounce behavior, and output logic require separate validation.
Digital Control Interface
The LM2903QDRG4Q1 can convert an analog threshold event into a wired digital signal for a controller or safety system. Its open-collector output can pull a low-power logic line low and release it to a pull-up when the comparison state changes, making the interface straightforward to implement. The 20 mA typical output current provides sinking capability, while the 2.5 mA maximum quiescent current limits static supply demand. According to the Texas Instruments LM2903-Q1 documentation, the device operates across a wide supply range and is qualified for automotive temperature grades 0 and 1. In practice, the pull-up value must balance bus rise time against sink current, and the system must define fail-safe states for open-collector or disconnected conditions. Input filtering may also be needed when the compared signal contains switching noise.
داتای سەرچاوەی ئەندازیاری بۆ LM2903QDRG4Q1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903QD | LM2903VQDRQ1 | LM2903D |
|---|---|---|---|---|
| Package | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels |
جیاکەرەوە سەرەکییەکان
- Explicit automotive qualification in the exact ordering option (بەراورد بەLM2903D)
- Wide operating supply range for protected automotive rails (بەراورد بەLM2903QD)
- Two independent channels in an 8-SOIC footprint (بەراورد بەLM2903VQDRQ1)
تێبینییەکانی دیزاین
Do not treat every LM2903-family order code as an automatic automotive substitute. The Q1 order code is identified as AEC-Q100 Grade 0 and 1, while the grade and qualification of other suffixes can differ. Before replacing LM2903QDRG4Q1, compare the full ordering table, package drawing, pin description, temperature range, qualification grade, input common-mode limits, and test conditions. A shared 8-SOIC outline is necessary for PCB compatibility but does not by itself prove functional or qualification equivalence.
Place each open-collector pull-up resistor close to the corresponding output so that switching transients do not couple into sensitive comparison inputs. Keep the pull-up return path and comparator ground connection within a low-impedance loop. Because the outputs can be released to a high-impedance state, the pull-up value determines the rising-edge speed and must satisfy the required logic rise time, bus capacitance, and available sink-current margin.
Add filtering at the compared inputs when the monitored signal contains switching noise or fast transients. A simple input RC network can suppress high-frequency interference, but its time constant must not distort the intended threshold event or create excessive delay. Check the reference node with the same noise and layout discipline applied to the signal input. The 7 mV maximum offset at 5 V is only one contributor to total decision error; divider tolerance, reference accuracy, input noise, and hysteresis can dominate the practical threshold accuracy.
Decouple the comparator supply close to the VCC and ground pins with a short, low-inductance connection. Keep sensitive divider and reference returns away from high-current switching paths. The maximum supply is 36 V, but the complete circuit must also tolerate automotive transients; use an appropriately rated protection network rather than relying on the comparator's supply limit as a surge-protection specification. Confirm that each input remains within the applicable common-mode range under every operating condition.
زانیاری پابەندبوون
Texas Instruments identifies LM2903QDRG4Q1 as AEC-Q100 Grade 0 and 1 qualified for automotive applications. RoHS, REACH, lead-free, halogen-free, and conflict-mineral statuses require confirmation from the current manufacturer material or compliance documentation.