LM2904ADMR2G - Dual 1 MHz Op Amp, 8-MSOP | onsemi
MPN: LM2904ADMR2G ✓ چالاکLM2904ADMR2G گشتی
A dual operational amplifier combines two independent amplifier channels in one package. Operational amplifiers are active analog devices used to amplify, buffer, compare, or filter signals. They belong to the broader semiconductor hierarchy of integrated circuits, analog ICs, amplifiers, and operational amplifiers. The LM2904 family is commonly used for industrial control, sensor interfaces, audio signal paths, and low-frequency analog processing where economical dual-channel operation is useful.
Key characteristics include a 3 MHz? No. The device has a 1 MHz gain-bandwidth product according to the manufacturer product description, low power drain, common-mode input voltage range extending to ground/VEE, and support for both single-supply and split-supply operation. The 8-MSOP package provides a compact surface-mount footprint for dual-channel analog designs. The LM2904ADMR2G is an active onsemi part according to the listed product information.
The LM2904ADMR2G uses internally compensated bipolar amplifier circuits. Internal compensation removes the need for an external frequency-compensation network in ordinary closed-loop configurations. Its common-mode behavior is appropriate for many industrial and embedded systems where inputs remain above the negative supply rail, but the design should be checked against the datasheet limits before operating close to the positive rail or outside the specified supply range.
Typical uses include instrumentation buffers, sensor amplifiers, active filters, comparators, audio preamplifier stages, and low-frequency control loops. In a single-supply system, the negative supply pin is connected to ground, while split-supply systems can use positive and negative rails. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance.
The principal design consideration is common-mode and output-range limitation. Unlike modern rail-to-rail-input amplifiers, the LM2904 family is not intended to cover the entire supply range at the input. Verify input common-mode voltage, output swing, supply current, stability, and noise performance against the application requirements. This page summarizes the part family, package, pinout, application considerations, and engineering-focused comparisons for design review and sourcing.
جێگرەوەکانی جێگۆڕکێ بۆ LM2904ADMR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904ADMR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature Range, Package.
LM2904DMR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NCV2904DMR2G
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2904ADMR2
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2904ADMR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Dual operational amplifier |
| Number of Amplifiers | 2 circuits |
| Gain-Bandwidth Product | 1 MHz |
| Supply Voltage Range | 3 V to 26 V |
| مەودای پلەی گەرمیی کارکردن | -40 C to +105 C |
| Input Common-Mode Voltage Range | Extends to ground/VEE |
| Supply Configuration | Single supply or split supply |
| Typical Low Supply-Current Drain | 0.7 mA |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 20 nA |
| Frequency Compensation | Internal |
| پاکێج | 8-MSOP, 0.118 inch width, 3.00 mm width |
| جۆری دامەزراندن | Surface mount |
| جۆری دەرچوون | Rail-to-rail output not specified |
| دۆخی چرخەی ژیان | Active |
ڕێکخستنی پینی LM2904ADMR2G
| پین 1 | OUT1 — Output of amplifier 1 |
| پین 2 | IN1- — Inverting input of amplifier 1 |
| پین 3 | IN1+ — Noninverting input of amplifier 1 |
| پین 4 | V- — Negative supply |
| پین 5 | IN2+ — Noninverting input of amplifier 2 |
| پین 6 | IN2- — Inverting input of amplifier 2 |
| پین 7 | OUT2 — Output of amplifier 2 |
| پین 8 | V+ — Positive supply |
بەکارهێنانە باوەکان
LM2904ADMR2G گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffer Stage, Active Filter and Analog Signal Conditioning, Comparator and Threshold Detection, Power Supply Feedback and Current Monitoring, Embedded Control and Instrumentation.
Industrial Sensor Signal Conditioning
The LM2904ADMR2G is suitable for conditioning low-frequency sensor signals when the sensor output remains within the amplifier's usable common-mode range. Its two independent channels can amplify one sensor signal while monitoring a reference or providing a second gain stage. The 1 MHz gain-bandwidth product supports moderate closed-loop bandwidth, and the typical 20 nA input bias current helps reduce loading on high-impedance sources. In a 5 V single-supply design, the common-mode range extending to ground/VEE helps with sensors that operate close to zero volts. Designers should verify output swing, offset error, noise, and the required gain against the sensor signal range.
پێشنیارکراو
Audio Preamplifier and Buffer Stage
The LM2904ADMR2G can provide gain and buffering in low-frequency audio preamplifier stages where rail-to-rail input operation is not required. Its dual-channel organization allows one channel to amplify an audio signal while the other handles a level-shift, monitor, or auxiliary function. The internally compensated architecture simplifies closed-loop design and supports common feedback configurations. A split-supply arrangement can center the signal around ground, while a single-supply arrangement requires careful input and output biasing. Before selecting it for a microphone or line-level input, check input bias current, input offset voltage, output swing, noise, and the maximum input signal against the circuit requirements.
پێشنیارکراو
Active Filter and Analog Signal Conditioning
The LM2904ADMR2G is appropriate for first-order and moderate-gain active filter stages operating well below its 1 MHz gain-bandwidth product. Two amplifier sections can implement independent low-pass, high-pass, or gain stages in compact analog signal-conditioning modules. Internal frequency compensation makes conventional inverting and noninverting configurations straightforward, while the 3 V to 26 V supply range supports portable and industrial rails. The designer must account for the amplifier's finite gain-bandwidth product, slew rate, output-current capability, and output-swing limits when selecting feedback resistors and capacitor values. Stable operation should be checked across the intended frequency range and supply tolerance.
پێشنیارکراو
Comparator and Threshold Detection
The LM2904ADMR2G can be used as a comparator when the required input and output operating points remain within the specified common-mode and output-swing limits. The two channels allow simultaneous comparison of two analog quantities or implementation of window-style detection with external resistor networks. Its low supply-current drain supports battery-powered or distributed monitoring systems, and operation from 3 V to 26 V covers a broad range of supply environments. The circuit should not be treated as a modern rail-to-rail comparator: verify input overdrive, output saturation, propagation delay behavior, and output drive for the specific logic or relay interface. A pull-up or pull-down arrangement may be required at the output.
پێشنیارکراو
Power Supply Feedback and Current Monitoring
The LM2904ADMR2G can amplify the error signal in a basic power-control loop or monitor a scaled voltage in a regulated supply. One channel may amplify the feedback divider while the other provides a current or voltage monitor for supervisory logic. Its low typical supply-current drain of 0.7 mA is useful when the monitor must operate continuously, while the wide 3 V to 26 V supply range permits operation across common industrial rails. The input common-mode limit is important because the feedback node may operate close to ground. Confirm the output drive, stability, offset contribution, and maximum differential input condition before using it in a power-conversion loop.
پێشنیارکراو
Embedded Control and Instrumentation
The LM2904ADMR2G is useful in embedded instrumentation designs that require two generic analog channels in a compact surface-mount package. Typical tasks include conditioning a transducer, buffering a reference, driving an analog measurement input, or amplifying an error signal before an ADC. Its internal compensation and low supply-current drain simplify analog infrastructure in cost-sensitive control boards, while the 8-MSOP footprint supports dense layouts. The design should include local supply bypassing and should maintain adequate common-mode headroom for the highest expected input voltage. Confirm ADC input range, amplifier output swing, settling requirements, and noise performance when connecting the outputs to a converter.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2904ADMR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2904DMR2G | NCV2904DMR2G | LM2904ADMR2 |
|---|---|---|---|---|
| Package | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP |
| Brand | onsemi | onsemi | onsemi | onsemi |
| Amplifier Configuration | Dual, 2 circuits | Dual, 2 circuits | Dual, 2 circuits | Dual, 2 circuits |
جیاکەرەوە سەرەکییەکان
- Compact dual-channel integration (بەراورد بەLM2904DMR2G)
- Single-supply common-mode operation near ground (بەراورد بەLM2904ADMR2)
- Automotive-oriented family option for qualifying designs (بەراورد بەNCV2904DMR2G)
تێبینییەکانی دیزاین
Place the input, output, and supply bypass components close to their corresponding pins. In single-supply operation, connect V− to the ground plane and provide local supply decoupling at V+. Keep feedback resistors and gain-setting networks close to the relevant input pins to reduce parasitic capacitance and improve switching behavior.
Do not assume rail-to-rail input or output operation. The common-mode range extends to ground or VEE, but the positive input limit and output swing must remain within the datasheet limits. When using the amplifier as a comparator, verify output saturation, input overdrive, and the required pull-up or pull-down network.
Check the selected closed-loop gain and feedback network against the 1 MHz gain-bandwidth product and the required settling behavior. High source impedances can create bias-current and offset errors, while capacitive loading can reduce stability. Use short, quiet signal paths and evaluate the complete analog channel with the intended source impedance and downstream load.
Use the specified 3 V to 26 V supply range and account for the typical 0.7 mA supply-current drain in battery or low-power designs. Because the same package contains two amplifiers, estimate the total supply demand under both channels' operating conditions. Add local bypassing and ensure the output does not exceed the load-current and output-swing limits.
زانیاری پابەندبوون
The available product information identifies onsemi as the manufacturer and lists the LM2904ADMR2G as active, but the required compliance declarations are not stated in the listed source material.