STMicroelectronics

LM2904AYPT - Dual Low-Power Op-Amp, 1.1MHz | STMicroelectronics

MPN: LM2904AYPT ✓ چالاک
3 V to 30 V Vdss 20 nA (typical) Id TSSOP-8 Package
MOQ: 1 |

LM2904AYPT گشتی

The STMicroelectronics LM2904AYPT is a low-power dual operational amplifier with two independent general-purpose amplifier circuits, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a single supply of 3 V to 30 V, housed in an 8-pin TSSOP package. The A suffix and Y suffix identify the automotive-grade version, which STMicroelectronics qualifies for harsh automotive and industrial environments with extended temperature capability.

An operational amplifier (op-amp) is an analog building block that amplifies the voltage difference between its two inputs with very high open-loop gain. As a member of the operational amplifier hierarchy, the LM2904 family sits under linear amplifiers, then amplifier ICs, then analog integrated circuits. Dual op-amps such as the LM2904A integrate two matched amplifiers in one package, saving board area and improving channel matching in multi-stage analog signal chains.

Key features include an input offset voltage of typically 2 mV (maximum 7 mV per the LM2904A grade), an input bias current of 20 nA, a large common-mode input range that extends to the negative rail, and single-supply operation down to 3 V. A power drain of only 0.7 mA per amplifier (typical) makes the part suitable for battery-powered and always-on circuits. Output current capability of approximately 20 mA per channel drives moderate loads directly.

The bipolar process technology used in the LM2904A provides rugged, well-understood behavior: graceful performance degradation near the rails, low 1/f-noise characteristics typical of bipolar input stages, and a unity-gain stable configuration requiring no external compensation capacitor. The internal 100 dB-class DC open-loop gain and good channel-to-channel matching support precision comparator, amplifier, and filter topologies.

Typical applications include automotive sensor signal conditioning (oxygen sensors, position sensors), battery monitors and current-sense amplifiers in 12 V and 24 V vehicle systems, industrial transducer front ends, active filters, comparators with hysteresis, and low-speed signal buffering in HVAC and appliance controllers.

When designing with the LM2904AYPT, remember that the output cannot swing fully to the positive rail and that phase reversal is avoided on the inverting input only within the specified common-mode range; keep gain-setting resistors above 10 kohm to limit bias-current error, and place a 100 nF decoupling capacitor within 5 mm of pin 8.

This page adds value beyond the manufacturer datasheet by combining drop-in alternative comparisons, application-specific design notes, parametric comparison tables, and sourcing guidance in one place.

جێگرەوەکانی جێگۆڕکێ بۆ LM2904AYPT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904AYPT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Gain-Bandwidth Product, Common-Mode Input Range, Number of Amplifiers.

STMicroelectronics
Package: 8-pin TSSOP
Amplifier Type: Dual general-purpose operational amplifier
Gain-Bandwidth Product: 1.1 MHz
بەراوردکردن لەگەڵ LM2904AYPT →
Texas Instruments
Package: 8-pin TSSOP (PW)
Amplifier Type: Dual general-purpose operational amplifier
Gain-Bandwidth Product: 700 kHz
بەراوردکردن لەگەڵ LM2904AYPT →
STMicroelectronics
Package: 8-TSSOP
Amplifier Type: Dual general-purpose operational amplifier
Gain-Bandwidth Product: 1.1 MHz
بەراوردکردن لەگەڵ LM2904AYPT →

LM2904YPT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
STMicroelectronics
📦 TSSOP-8
Dual general-purpose operational amplifier · 2 channels · Single-ended output per channel · 1.1 MHz · 100 dB · Low power · 8-TSSOP · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904APT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 TSSOP-8
A grade without Y automotive temperature designation, otherwise pin-to-pin identical

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM358AYPT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 TSSOP-8
LM358A commercial/industrial grade in same TSSOP-8, narrower guaranteed temperature range (-50% temperature margin vs +125C)

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904BPWR

✅ جێگرەوەی ڕاستەوخۆ
📦 TSSOP-8
TI newer silicon, improved offset and input characteristics, TI positions as pin-to-pin upgrade

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904BQDR

✅ جێگرەوەی ڕاستەوخۆ
📦 TSSOP-8
same LM2904B upgraded die, TSSOP-8 surface-mount package, automotive temperature grade

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904AYPT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 2
Amplifier Type General-purpose, bipolar, single-ended
Gain Bandwidth Product 1.1 MHz
Slew Rate 0.6 V/us
Supply Voltage Range (Single Supply) 3 V to 30 V
Supply Voltage Range (Dual Supply) +/-1.5 V to +/-15 V
Input Bias Current 20 nA (typical)
Input Offset Voltage 2 mV typical / 7 mV maximum (A grade)
Supply Current per Amplifier 0.7 mA (typical)
Output Current per Channel 20 mA (typical)
Common-Mode Input Range 0 V to VCC - 1.5 V
مەودای پلەی گەرمیی کارکردن -40C to +125C
پاکێج TSSOP-8
جۆری دامەزراندن Surface Mount
Qualification Automotive grade (AEC-Q100 qualified per ST automotive family designation)
دۆخی RoHS Compliant

ڕێکخستنی پینی LM2904AYPT

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
پین 1 OUT1 — Amplifier A output
پین 2 IN1- — Amplifier A inverting input
پین 3 IN1+ — Amplifier A non-inverting input
پین 4 VCC-/GND — Negative supply or ground (single supply)
پین 5 IN2+ — Amplifier B non-inverting input
پین 6 IN2- — Amplifier B inverting input
پین 7 OUT2 — Amplifier B output
پین 8 VCC+ — Positive supply

بەکارهێنانە باوەکان

LM2904AYPT گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Battery Monitoring and Current-Sense Amplification, Industrial Transducer Front Ends, Active Filters and Signal Buffers, Comparators with Hysteresis, HVAC and Appliance Controllers.

🚗

Automotive Sensor Signal Conditioning

The LM2904AYPT is designed for automotive environments: the Y suffix guarantees -40C to +125C operation and the A grade tightens the offset voltage specification, which matters for oxygen-sensor, position-sensor, and pressure-sensor signal chains where millivolt-level accuracy affects closed-loop control. The 3 V to 30 V supply range accepts direct connection to the 12 V vehicle battery rail, including cold-crank and load-dump conditions below the absolute maximum. Typical circuits include differential amplifiers reading grounded sensors, non-inverting buffers driving the ADC input of a body controller, and hysteresis comparators for switch-point detection. Because each package contains two matched amplifiers, one device often handles both a conditioning gain stage and a threshold comparator, reducing BOM count. Decouple pin 8 with 100 nF and route sensor inputs away from ignition noise sources.

⚡

Battery Monitoring and Current-Sense Amplification

In battery monitors and low-side current-sense circuits, the LM2904AYPT's common-mode input range extending to the negative rail is the key parameter: the amplifier reads signals at or near 0 V without phase reversal, enabling accurate low-side shunt measurements. The 20 nA input bias current limits shunt-value error, and the A-grade 7 mV maximum offset keeps threshold accuracy within practical limits for 12 V lead-acid and 24 V industrial battery systems. A common topology uses one amplifier as a difference amplifier across the shunt and the second channel as an undervoltage comparator with hysteresis fed from a resistor divider. The 0.7 mA per-amplifier supply current keeps the monitor's own drain negligible in always-on applications. Power the device from the battery rail through a series resistor plus zener clamp for robustness.

🏭

Industrial Transducer Front Ends

Industrial 24 V control cabinets routinely use the LM2904AYPT to amplify signals from thermistors, strain gauges, and 4-20 mA loop-derived voltages. The 30 V maximum supply accepts the 24 V rail directly without a pre-regulator, and the -40C to +125C temperature range survives unconditioned electrical rooms and outdoor enclosures. A typical design chains the two amplifiers: the first channel amplifies a bridge or divider signal by 10x to 100x with 1% metal-film resistors, and the second channel buffers or filters the result before the plant ADC. The 1.1 MHz bandwidth comfortably covers DC to 10 kHz signals typical of process transducers. Use resistor values above 10 kohm to minimize bias-current error and add RC input filtering for EMI immunity near contactors and variable-frequency drives.

🎧

Active Filters and Signal Buffers

The LM2904AYPT implements Sallen-Key and multiple-feedback active filters for anti-aliasing and noise rejection up to the tens-of-kilohertz range; the 1.1 MHz gain-bandwidth product limits the practical corner frequency to roughly 20-30 kHz for high-Q designs, beyond which filter response deviates from the ideal. The unity-gain stable bipolar design needs no external compensation, simplifying second-order sections to two resistors and two capacitors per amplifier. As a buffer, the 20 mA output current directly drives ADC inputs, cables, and LED indicators, while the output's ability to sink close to ground suits single-supply circuits referencing 0 V. In audio-adjacent industrial applications, place a small series resistor (around 50 ohm) at the output to isolate capacitive cable loads and prevent ringing. Use the two channels for a two-stage cascade in one TSSOP-8 footprint.

🔧

Comparators with Hysteresis

Many designs use one LM2904AYPT channel as a comparator with resistor-programmed hysteresis for battery undervoltage lockout, over-temperature flags, and limit switches. The single-supply common-mode range reaching ground and the output swinging near 0 V produce clean logic transitions into microcontroller inputs without level shifting. Add hysteresis of typically 1% to 5% of the threshold (for example, +/-200 mV on a 5 V threshold) via positive feedback around the non-inverting input to prevent chatter near the switching point. Respect the 0.6 V/us slew rate: propagation to a full swing takes several microseconds, so this technique is appropriate for DC and slowly varying signals, not fast pulse discrimination. The second channel can simultaneously implement the reference divider buffer, keeping the reference stiff against threshold-current changes.

💡

HVAC and Appliance Controllers

Heating, ventilation, air-conditioning, and white-goods controller boards favor the LM2904AYPT for NTC thermistor linearization, fan speed error amplification, and current-limit detection. The wide 3 V to 30 V supply range tolerates the poorly regulated auxiliary supplies common in appliance electronics, and the low 0.7 mA per-amplifier quiescent current supports standby-power budgets mandated by energy regulations. A typical furnace controller uses one channel to amplify the divided thermistor voltage into the ADC range and the other as a flame-current or blower-fault comparator. The A-grade offset specification improves trip-point repeatability across production units. Keep the amplifier inputs away from relay coils and triac snubbers, use a local 100 nF plus bulk 10 uF decoupling pair, and prefer ground-plane routing for the analog section to maintain signal integrity.

What is the supply voltage range of LM2904AYPT?
The LM2904AYPT operates from a single supply of 3 V to 30 V, or from dual supplies of +/-1.5 V to +/-15 V. According to the STMicroelectronics LM2904A datasheet, the wide supply range covers automotive 12 V battery systems, 24 V industrial rails, and low-voltage 3.3 V logic-side analog circuits, all with the same 8-pin TSSOP device.
What is the bandwidth of LM2904AYPT?
The LM2904AYPT has a gain-bandwidth product of 1.1 MHz with a slew rate of 0.6 V/us. This bandwidth suits DC and low-frequency analog work up to roughly 100 kHz at moderate gain, such as sensor conditioning, active filters, and comparator circuits. For signals above several hundred kilohertz, select a faster op-amp family instead of expecting unity-gain operation at 1 MHz.
Is LM2904AYPT automotive qualified?
Yes. The A and Y suffixes designate the automotive-grade LM2904A family from STMicroelectronics, specified from -40C to +125C and qualified for automotive applications. The base LM2904 (without the A suffix) carries a narrower specification set, so use the LM2904AYPT when the design must survive under-hood temperatures or meet automotive quality requirements.
What is the difference between LM2904A and LM2904?
The LM2904A is the enhanced-specification version of the LM2904: STMicroelectronics guarantees a tighter maximum input offset voltage (7 mV versus the wider base-grade limit) and specifies operation to +125C for automotive environments. Both are dual bipolar op-amps with identical 1.1 MHz bandwidth, 0.6 V/us slew rate, and the same industry-standard pinout, so the LM2904A is a drop-in upgrade wherever precision or temperature is a concern.
Can LM358 replace LM2904AYPT?
The LM358 is electrically similar but is the commercial/industrial-grade counterpart. The LM2904AYPT is the automotive-qualified member specified to +125C, so it can replace the LM358 in almost every circuit, but an LM358 cannot always replace the LM2904A where the wider temperature range or automotive qualification is mandatory. Pinout, bandwidth (1.1 MHz), and supply range (3 V to 30 V) are effectively identical between the families.
What is the best drop-in replacement for LM2904AYPT?
For the same footprint in TSSOP-8, the closest drop-in parts are STMicroelectronics LM2904YPT and LM2904APT (same die family, non-A grade limits) and the TI LM2904B family upgrade, which TI lists as a pin-to-pin replacement with improved offset and input characteristics. All share the industry-standard dual-op-amp pinout: pin 1 output A, pin 2 inverting A, pin 3 non-inverting A, pin 4 ground/V-, pins 5-7 channel B, pin 8 VCC/V+.
Where can I download the LM2904AYPT datasheet PDF?
The LM2904AYPT datasheet PDF is available for free download from the STMicroelectronics website (st.com) on the LM2904A product page, and mirrored datasheet repositories such as datasheets.com and alldatasheet.com also host the 28-page document. Always use the STMicroelectronics original as the authoritative reference for electrical limits, application circuits, and package mechanical drawings.
What is the LM2904AYPT pinout in TSSOP-8?
The LM2904AYPT uses the industry-standard dual-op-amp TSSOP-8 pinout. Pin 1 is amplifier A output, pin 2 is amplifier A inverting input, pin 3 is amplifier A non-inverting input, pin 4 is ground (V-) for single-supply use, pin 5 is amplifier B non-inverting input, pin 6 is amplifier B inverting input, pin 7 is amplifier B output, and pin 8 is the positive supply (V+). This pinout is shared across the LM358/LM2904 family, making footprint reuse simple.
What are the key specifications of LM2904AYPT that engineers should know?
The STMicroelectronics LM2904AYPT is a dual bipolar op-amp with 1.1 MHz gain-bandwidth, 0.6 V/us slew rate, 3 V to 30 V single-supply operation, 20 nA input bias current, 2 mV typical (7 mV max) offset voltage in the A grade, and 0.7 mA typical supply current per amplifier. It is rated -40C to +125C in an 8-pin TSSOP package and is automotive qualified. These numbers make it a workhorse for low-frequency, low-power analog signal conditioning.
Is LM2904AYPT suitable for a 24V industrial system?
Yes. The 30 V maximum supply rating of the LM2904AYPT leaves comfortable margin on 24 V industrial rails, and the -40C to +125C operating range covers industrial cabinets and outdoor equipment. Keep the output voltage swing expectations realistic - the output approaches the negative rail closely but stops roughly 1.5 V short of the positive rail - and design gain stages so that full-scale signals stay within this linear window.
Can LM2904AYPT be used as a comparator?
Yes, within limits. The LM2904AYPT can function as a low-speed comparator with hysteresis for signals well below its 1.1 MHz bandwidth, a common practice in battery undervoltage detection and window comparators. However, an op-amp used as a comparator has slower response and no dedicated open-collector output, so for sub-microsecond switching, ESD-sensitive nodes, or logic-level outputs, a purpose-built comparator is the better engineering choice.
LM2904AYPT vs LM2904YPT - which is better for automotive design?
For automotive designs, the LM2904AYPT is the correct choice because the A suffix guarantees the enhanced specification set (tighter offset voltage limits) and the Y suffix denotes automotive temperature qualification to +125C. The LM2904YPT shares the same die, package, and pinout but carries the standard-grade limits, so substituting it would relax guaranteed accuracy in sensor signal chains. Choose the AYPT version whenever a design specification references automotive qualification.
When should I choose LM2904AYPT over TI LM2904B?
Choose the STMicroelectronics LM2904AYPT when your design already qualifies ST automotive parts, requires the documented A-grade offset limits, or when second-sourcing strategy keeps the dual-source pair ST plus TI. Choose the TI LM2904B when you want TI's newer silicon with improved offset and input characteristics, which TI positions as a pin-to-pin upgrade. Both operate from 3 V to 30 V and use the same dual-op-amp pinout, so either drops into the same TSSOP-8 footprint.
What is the TI equivalent for LM2904AYPT?
The closest Texas Instruments equivalent is the LM2904B family, which TI explicitly lists as a pin-to-pin replacement with upgraded functionality compared with the standard LM2904, available in the same 8-pin surface-mount packages including TSSOP. Because TI markets the LM2904B as a pin-to-pin upgrade rather than an A-grade clone, verify the offset voltage and temperature grade in the TI datasheet before committing it as a form-fit-function substitute in an automotive design.
Where to buy LM2904AYPT and how do I get a quote?
LM2904AYPT can be ordered through the Request a Quote form on this page. Submit your required quantity and target delivery date, and the quote response will include current pricing, stock status, lead time, and packing options (tape and reel for the TSSOP-8 package). The manufacturer also lists the part on its own online store, and distributors stock the part regularly, but XAIPART consolidates sourcing, pricing, and support through a single quote channel.

داتای سەرچاوەی ئەندازیاری بۆ LM2904AYPT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2904AYPT when you need an automotive-qualified dual op-amp for 12 V or 24 V systems with guaranteed limits to +125C: battery monitors, sensor conditioning, and appliance controllers are its sweet spot. Choose LM2904YPT for the same silicon at standard grade when your specification does not require A-grade limits. Choose LM2904APT when the tighter offset matters but full automotive temperature qualification does not. Choose LM358AYPT only for commercial/industrial designs to +85C, where it is usually the least expensive A-grade dual in the same footprint. Choose the TI LM2904B family when offset accuracy is the dominant requirement - TI's upgraded die offers roughly 3 mV maximum offset - accepting a typically higher unit price. Trade-off summary: the LM2904AYPT maximizes qualification and cost balance, not bandwidth or precision; for sub-mV offsets or multi-MHz signals, select a precision or high-speed op-amp family instead.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2904YPT LM2904APT LM358AYPT LM2904BPWR
Package TSSOP-8 TSSOP-8 - same TSSOP-8 - same TSSOP-8 - same TSSOP-8 - same
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments
Gain Bandwidth Product 1.1 MHz 1.1 MHz 1.1 MHz 1.1 MHz 1.2 MHz (upgraded die)
Supply Voltage Range 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 36 V
Input Offset Voltage (max) 7 mV (A grade) 9 mV (standard grade) 7 mV (A grade) 7 mV (A grade) 3 mV (B upgrade)
Operating Temperature -40C to +125C (automotive) -40C to +125C -40C to +105C -40C to +85C (industrial) -40C to +125C
Slew Rate 0.6 V/us 0.6 V/us 0.6 V/us 0.6 V/us 0.5 V/us
Automotive Qualification Yes (A + Y suffix) Yes (Y suffix) No (A grade only) No (industrial grade) Yes (automotive family)

جیاکەرەوە سەرەکییەکان

  • Automotive-grade temperature and specification limits (بەراورد بەLM358AYPT)
  • Tighter guaranteed offset than the standard-grade same-package part (بەراورد بەLM2904YPT)
  • Lower supply headroom requirement than the TI upgrade (بەراورد بەLM2904BPWR)

تێبینییەکانی دیزاین

Supply the LM2904AYPT from a single rail between 3 V and 30 V with a 100 nF ceramic capacitor within 5 mm of pin 8 plus a 10 uF bulk capacitor per board. In automotive and industrial environments, add a series resistor and transient suppressor on the supply feed because load-dump and switching transients can exceed the 32 V absolute maximum. Estimated: at 30 V supply and 0.7 mA per amplifier, device dissipation is only about 21 mV-level quiescent power plus output-stage load, so no thermal design effort is needed unless outputs drive heavy DC loads continuously.

The output stage of the LM2904A swings close to ground but stops approximately 1.5 V short of the positive rail; design gain stages so full-scale signals stay within this window or the output clips asymmetrically. Keep gain-setting resistors above 10 kohm so the 20 nA input bias current contributes negligible offset error (for example, 20 nA through 10 kohm is only 0.2 mV). When driving long cables or capacitive loads above about 100 pF, insert a 50 ohm series isolation resistor at the output to prevent ringing and sustained oscillation.

Do not rely on the LM2904A for fast switching: the 0.6 V/us slew rate means a 0 V to 30 V output transition takes about 50 us, and using an op-amp as a comparator adds microseconds of response delay. Avoid applying inputs more than 0.3 V below the V- pin in dual-supply circuits to prevent abnormal input-stage behavior. Verify the suffix on incoming parts - the standard-grade LM2904 and the automotive LM2904AYPT share one pinout but different guaranteed limits, and substituting down silently degrades accuracy in A-grade sensor chains.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS compliant and lead-free per STMicroelectronics product listings; the A/Y suffix denotes ST automotive qualification. Reach and halogen-free status should be confirmed on the ST product page environmental documents.

داتا پشتڕاستکراوەتەوە لە: 2026-11-17 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2904AYPT datasheet LM2904AYPT datasheet pdf LM2904AYPT pinout LM2904AYPT equivalent LM2904AYPT replacement LM2904AYPT cross reference LM2904AYPT vs LM2904B STMicroelectronics LM2904AYPT LM2904A TSSOP-8 pinout dual op amp 1.1MHz automotive grade LM2904AYPT price stock LM2904A application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

STMicroelectronics LM2904AYPT LM2904 LM2904A LM358 LM2904B Texas Instruments operational amplifier op-amp dual amplifier linear amplifier analog IC TSSOP-8 surface mount AEC-Q100 RoHS gain-bandwidth product slew rate input offset voltage automotive sensor conditioning battery monitoring single-supply operation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ