STMicroelectronics

LM2904PT - Dual Low Power Op-Amp, TSSOP-8 | STMicroelectronics

MPN: LM2904PT ✓ چالاک
up to 30 V Vdss 8-TSSOP (PT) Package
MOQ: 1 |

LM2904PT گشتی

The STMicroelectronics LM2904PT is a low-power dual operational amplifier consisting of two independent, internally frequency-compensated op-amps in an 8-pin TSSOP (PT) package. It operates from supply voltages up to 30 V (single-supply) or +/-15 V (dual-supply) and integrates two general-purpose amplifier circuits per package.

A dual operational amplifier is a voltage-regulating analog IC that amplifies the difference between two input terminals while providing high input impedance and low output impedance. Within the amplifier hierarchy, it sits at the general-purpose op-amp level - a subcategory of linear amplifier ICs within the broader analog signal-conditioning and power management semiconductor families. Dual op-amps are preferred where two gain stages or filters are needed in one footprint, saving board space and BOM cost.

Key features of the LM2904PT include single-supply operation with input common-mode range that includes ground, internally compensated unity-gain stability, and a 1.1 MHz gain-bandwidth per the device comparisons published by distributors. The wide supply range of 30 V supports industrial 24 V rails directly, which is the main reason the LM2904 family dominates industrial and automotive signal-conditioning sockets.

Architecturally, the device is a bipolar (bipolar junction transistor) design, as ST describes it as a low power bipolar op-amp. Bipolar process technology gives robust ESD tolerance and predictable behavior over temperature, at the cost of higher quiescent current than CMOS alternatives. The two amplifiers share bias circuitry, so total supply current is lower than two single op-amps.

Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators in non-critical precision roles, motor-control sensing circuits, and general industrial signal conditioning. The single-supply, ground-sensing input is especially convenient for battery-powered and 24 V industrial systems where a negative rail is unavailable.

For design, note that the output stage cannot swing fully to the positive rail - reserve headroom on the high side, and avoid driving the output into deep saturation if fast recovery is needed. Input offset voltage limits use in precision DC measurement; select a precision op-amp for microvolt-level applications.

This page synthesizes distributor cross-references, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

جێگرەوەکانی جێگۆڕکێ بۆ LM2904PT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904PT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Gain Bandwidth Product, Slew Rate, Number of Channels.

STMicroelectronics
Package: 8-pin TSSOP
Amplifier Type: Low-power dual operational amplifier
بەراوردکردن لەگەڵ LM2904PT →
STMicroelectronics
Package: TSSOP-8 (8TSSOP), 8 pins
Number of Channels: 2
بەراوردکردن لەگەڵ LM2904PT →
Texas Instruments
Package: 8-SOIC (D)
Amplifier Type: General Purpose
Gain Bandwidth Product: 700 kHz
بەراوردکردن لەگەڵ LM2904PT →
STMicroelectronics
Package: 14-pin TSSOP
Amplifier Type: Standard general-purpose operational amplifier
Gain Bandwidth Product: 1.3 MHz
بەراوردکردن لەگەڵ LM2904PT →
STMicroelectronics
Package: 8-TSSOP
Amplifier Type: Standard general-purpose operational amplifier
بەراوردکردن لەگەڵ LM2904PT →
STMicroelectronics
Package: 8-pin TSSOP
بەراوردکردن لەگەڵ LM2904PT →
STMicroelectronics
Package: 8-pin SOIC
Amplifier Type: Dual general-purpose operational amplifier
Slew Rate: 1 V/µs
بەراوردکردن لەگەڵ LM2904PT →

LM358PT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 TSSOP-8 (PT)
2 amplifiers · General-purpose operational amplifier · 2 circuits · 3 V to 32 V · Single supply · 1.1 MHz · 100 dB · 0.6 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358APT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 TSSOP-8 (PT)
Standard general-purpose operational amplifier · 2 channels · 2 circuits · 8-TSSOP · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904PT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 TSSOP-8 (PT)
2 · Single-Ended · 1.1 MHz · up to 30 V · +/-15 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 TSSOP-8 (PT)
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TS922AID

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 TSSOP-8 (PT)
Dual general-purpose operational amplifier · 2 circuits · BiCMOS · Yes · Yes · 3 V and 5 V · 12 V · 80 mA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904PT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Circuits 2
جۆری دەرچوون Single-Ended
Gain Bandwidth Product 1.1 MHz
Supply Voltage Range (Single) up to 30 V
Supply Voltage Range (Dual) +/-15 V
Technology Bipolar
پاکێج 8-TSSOP (PT)
جۆری دامەزراندن Surface Mount
دۆخی RoHS ROHS3 Compliant
Amplifier Type Standard (General Purpose)
Product Series LM2904 (Low Power Dual Operational Amplifier)

ڕێکخستنی پینی LM2904PT

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 GND / V- — Ground or negative supply
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 VCC / V+ — Positive supply

بەکارهێنانە باوەکان

LM2904PT گونجاوە بۆ 6 بەکارھێنانs: Industrial Transducer Amplification, Automotive Signal Conditioning, Active Filter Design, Battery-Powered Portable Devices, Motor Control Sensing, Audio Line-Level Signal Chains.

🏭

Industrial Transducer Amplification

Industrial sensors such as pressure bridges, thermocouple conditioners, and current-shunt monitors produce small differential signals that must be amplified before digitization. The LM2904PT fits this role because its input common-mode range extends to ground, allowing direct interface to ground-referenced sensor outputs on a single 24 V industrial rail, and its 30 V supply rating removes the need for a pre-regulator. Each of the two amplifiers handles one gain stage, so a typical two-stage amplification chain fits in one package. With a 1.1 MHz gain bandwidth, the device supports gains of 10 to 100 for DC and low-frequency signals up to tens of kilohertz. Reserve high-side output headroom, since the output does not swing fully to the positive rail, and keep closed-loop gain modest to preserve accuracy.

🚗

Automotive Signal Conditioning

The LM2904 designation denotes STMicroelectronics' industrial and automotive temperature-qualified grade of the LM358 architecture, making the LM2904PT a recurring choice in body electronics, battery monitoring, and sensor buffering modules in vehicles. Its 30 V total supply rating survives automotive load-dump-protected 12 V rails and 24 V truck systems, while the bipolar process tolerates the electrical stress of the vehicle environment. Ground-sensing inputs allow single-supply operation from the vehicle battery without a negative rail, simplifying the analog power tree. Each package provides two channels, so one TSSOP-8 can condition two sensors such as throttle position and coolant level. Designers should verify extended-temperature electrical characteristics in the ST datasheet and account for the non-rail-to-rail output when scaling signals near the positive supply.

🔧

Active Filter Design

Active low-pass, high-pass, and Sallen-Key filters for anti-aliasing and noise removal use general-purpose op-amps as gain elements, and the LM2904PT supplies two independent amplifiers for second-order filter sections in one TSSOP-8 footprint. The internally compensated design is unity-gain stable, so filters can be built at gains of 1 or higher without external compensation, and the 1.1 MHz gain bandwidth supports corner frequencies up to roughly 10 kHz with stable, predictable phase behavior. Single-supply operation with ground-including common-mode range lets filters run from the same 5 V or 24 V rail as the rest of the system, with mid-rail bias generated by a resistor divider buffered by the second amplifier in the package. For filters above approximately 50 kHz, select a wider-bandwidth op-amp.

📱

Battery-Powered Portable Devices

Battery-powered instruments, meters, and handheld devices need amplifiers that operate directly from a single low-voltage cell or regulated rail without a negative supply. The LM2904PT meets this requirement because its input common-mode range includes ground and it remains functional at single supplies of a few volts, while the shared bias network of the dual design keeps total quiescent draw lower than two separate single op-amps. The two channels typically serve one signal-conditioning stage and one comparator-style level detector, consolidating analog functions in a single 8-pin package and reducing board area in compact enclosures. Note that the bipolar process draws more supply current than modern CMOS op-amps, so for multi-year coin-cell operation compare quiescent figures and consider a CMOS rail-to-rail alternative.

⚙️

Motor Control Sensing

Motor-drive systems monitor current through shunt resistors and buffer speed or position feedback signals, tasks where the LM2904PT's 30 V supply rating and ground-sensing inputs are directly useful. A shunt in the low-side return path develops a ground-referenced voltage that the LM2904PT amplifies with a simple non-inverting gain configuration on a single 24 V rail, and the second amplifier can buffer a tachometer or Hall-sensor signal in the same package. The 1.1 MHz bandwidth is sufficient for average-current monitoring loops at switching frequencies of a few kilohertz, though cycle-by-cycle peak current control at higher PWM frequencies needs a faster amplifier. Ensure the output high-side headroom matches the ADC input range when scaling the amplified shunt signal.

🎧

Audio Line-Level Signal Chains

Consumer and industrial audio equipment uses general-purpose dual op-amps for line buffering, mixing, and gain staging, and the LM2904PT serves cost-sensitive roles in these chains. Its 1.1 MHz gain bandwidth supports unity-gain and moderate-gain buffering across the full audio band (20 Hz to 20 kHz) with adequate open-loop gain to keep distortion low at line levels, and the dual channels handle stereo left and right in one TSSOP-8. Operation from a single supply with a mid-rail virtual ground suits battery-powered recorders and intercoms. For high-fidelity designs requiring lower noise, higher output drive, or faster slew, dedicated audio op-amps such as the TS922 or TS972 from ST provide measurably better distortion and drive figures in the same outline.

What is the LM2904PT and what does it do?
The LM2904PT is a low-power dual operational amplifier from STMicroelectronics containing two independent, internally compensated op-amp circuits in an 8-pin TSSOP package. It supports supply voltages up to 30 V single-supply or +/-15 V dual-supply, and its input common-mode range includes ground, which makes it well suited to single-supply industrial and automotive signal conditioning. According to the STMicroelectronics datasheet, the part is a bipolar general-purpose amplifier, and distributor listings classify it as a Standard (General Purpose) Amplifier, 2 Circuit, Single-Ended.
What is the gain bandwidth of the LM2904PT?
The LM2904PT has a gain bandwidth product of approximately 1.1 MHz. This figure appears in distributor comparison data (Utmel lists the LM2904PT as a 30 V, 1.1 MHz low-power dual operational amplifier). At 1.1 MHz GBW, each amplifier delivers a gain of 10 up to roughly 110 kHz and unity-gain stability up to about 1.1 MHz, which covers typical transducer amplification, active filtering, and DC gain-block roles. For applications needing higher bandwidth, consider faster op-amp families.
What is the maximum supply voltage of the LM2904PT?
The LM2904PT supports a total supply voltage of up to 30 V, either as a single supply (0 V to 30 V) or dual supplies (+/-15 V). This wide range is stated in distributor comparison listings and is a signature characteristic of the LM2904 family. The 30 V rating allows direct connection across industrial 24 V rails without a pre-regulator, which is one of the main reasons this family remains a default choice in industrial signal-conditioning designs.
What is the difference between LM2904PT and LM358PT?
The LM2904PT and LM358PT are both STMicroelectronics dual op-amps in the same TSSOP-8 package with an identical pinout; the LM2904 is the industrial/automotive temperature-rated variant of the consumer-grade LM358. Both offer roughly 1.1 MHz gain bandwidth and 30 V supply capability, so for most designs they are pin-to-pin interchangeable. The key difference is the guaranteed operating temperature range and related specifications - the LM2904 carries the extended-range ratings intended for harsh environments. Choose the LM2904PT when the board must operate over industrial or automotive temperature extremes.
What is the best drop-in replacement for the LM2904PT?
The best drop-in replacement for the LM2904PT is the STMicroelectronics LM358PT, which uses the same TSSOP-8 package and identical pinout with matching 1.1 MHz and 30 V ratings. Cross-brand drop-in equivalents include the ROHM LM2904PT in the 8-TSSOP-B package and the SGMicro LM2904, which distributors document as functional equivalents. Before substitution, verify the package suffix matches your PCB footprint, because TSSOP pinout conventions can vary between manufacturers, and check the temperature grade in each datasheet.
Is the ROHM LM2904PT pin-compatible with the ST LM2904PT?
The ROHM LM2904PT is listed in the same 8-pin TSSOP-B package and provides the same dual general-purpose op-amp function rated at +/-16 V or 32 V, per ROHM's distributor listings. The electrical function and pin assignment follow the industry-standard dual op-amp arrangement, so it is commonly used as a cross-brand substitute. However, verify the exact TSSOP-B package drawing against your PCB land pattern, because ROHM's TSSOP-B dimension conventions differ slightly from JEDEC TSSOP on some dimensions; confirm footprint compatibility in both datasheets before committing the layout.
When should I choose the LM2904PT over a CMOS op-amp?
Choose the LM2904PT when you need a low-cost, rugged bipolar dual op-amp for single-supply industrial signal conditioning up to 30 V, especially where the input must sense near ground. The bipolar design tolerates abuse well and behaves predictably over temperature. Choose a CMOS op-amp instead when you need microvolt input offset, picoamp bias current, rail-to-rail output swing, or very low quiescent current for battery-powered designs. The LM2904PT output does not swing to the positive rail, so reserve headroom on the high side in your design budget.
Can the LM2904PT operate from a single 5 V supply?
Yes, the LM2904PT operates from a single 5 V supply and even lower, since its input common-mode range extends to ground and it is fully specified for single-supply operation. The output can pull close to ground under light load, which suits 0 V-referenced sensor signals. Note that the output cannot reach the positive rail - on a 5 V supply, expect roughly a volt or more of high-side headroom depending on load current. For full rail-to-rail output on low-voltage logic supplies, select a rail-to-rail CMOS op-amp instead.
Where can I download the LM2904PT datasheet PDF?
The LM2904PT datasheet PDF is available from STMicroelectronics through its official product and e-store pages (estore.st.com lists the LM2904PT as a low power bipolar op-amp), and mirror copies are hosted on datasheet aggregators such as AllDataSheet, which carries the 22-page ST datasheet for the LM2904PT. The datasheet contains the full electrical characteristics table, package mechanical drawings, pin configuration, and application information. Always prefer the manufacturer's official download for the latest revision before finalizing a design.
Where can I find the LM2904PT pinout?
The LM2904PT follows the industry-standard dual op-amp TSSOP-8 pinout: pin 1 is OUT1, pin 2 is IN1-, pin 3 is IN1+, pin 4 is GND/V-, pin 5 is IN2+, pin 6 is IN2-, pin 7 is OUT2, and pin 8 is VCC/V+. This arrangement is shown in the pin configuration section of the STMicroelectronics datasheet and matches the majority of dual op-amps, which is why cross-brand substitution is generally straightforward. Use the manufacturer datasheet drawing when routing PCB tracks to confirm the TSSOP-8 footprint dimensions.
How much does the LM2904PT cost and where can I buy it?
The LM2904PT is a high-volume commodity op-amp with low unit cost; LCSC lists it in stock with pricing starting in the sub-dollar range. XAIPART offers this part through the Request a Quote form on this page, where you can obtain current unit pricing, stock quantity, and lead time directly. Because pricing for commodity op-amps changes frequently with volume breaks, request a quote with your required quantity rather than relying on static listed prices, and mention any tape-and-reel packaging preference.
Is the LM2904PT in stock and what is the lead time?
The LM2904PT is listed as an active, in-production part by STMicroelectronics, and multiple distributors carry it as a stocked item, so availability is generally good with short lead times. XAIPART confirms live stock and the current lead time through the Request a Quote form on this page - submit your quantity and packaging preference (tape and reel or cut tape) and you will receive an up-to-date commitment. Because this is a mature commodity part, supply risk is low, but confirm lead time for large production volumes.
What can replace the LM2904PT?
You can replace the LM2904PT with the STMicroelectronics LM358PT (same brand, same TSSOP-8 footprint, consumer temperature grade) or the STMicroelectronics LM358APT. Cross-brand, the ROHM LM2904PT (8-TSSOP-B, dual GP op-amp, +/-16 V or 32 V) and the SGMicro LM2904 are documented functional equivalents. All share the standard dual op-amp pin arrangement, making them near drop-in candidates. TI application engineers also note newer family members such as the LM2904B with improved specifications; verify offset voltage and supply range against your requirements before switching.
What is the best SGMicro equivalent for the LM2904PT?
The best SGMicro equivalent for the LM2904PT is the SGMicro LM2904, which cross-reference services (Senneon) document as the closest functional alternative, with no recorded specification differences in the cited evidence. SGMicro manufactures the LM2904 dual op-amp to the same functional specification; confirm the package code (SOP-8 versus TSSOP-8) matches your PCB footprint before ordering, since SGMicro's standard offering is typically the SOP-8 outline. Review both datasheets for operating temperature range and offset voltage limits under your specific application conditions.
What are the key specifications of the LM2904PT that engineers should know?
The LM2904PT is a dual, bipolar, general-purpose operational amplifier from STMicroelectronics in TSSOP-8. Key numbers: two amplifier circuits per package, 1.1 MHz gain bandwidth, supply operation up to 30 V single or +/-15 V dual, input common-mode range extending to ground, and unity-gain internal compensation. The part is RoHS3 compliant, surface mount, and industrially temperature-qualified per the LM2904 designation. Its limitations are bipolar-class offset voltage, non-rail-to-rail output swing, and a modest slew rate - adequate for transducer amplification, active filters, and DC gain blocks, but not for precision or high-speed signal chains.

داتای سەرچاوەی ئەندازیاری بۆ LM2904PT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2904PT when you need a low-cost dual general-purpose op-amp qualified for industrial or automotive temperatures, running single-supply up to 30 V with inputs that sense ground. Choose the LM358PT when the board stays in commercial/industrial environments and lowest cost matters most - it is pin-identical with the same 1.1 MHz bandwidth. Choose the ROHM LM2904PT as a second source for supply-chain resilience, after confirming the 8-TSSOP-B footprint against your land pattern and noting its higher 32 V rating. Choose the SGMicro LM2904 when cost is the dominant criterion in high-volume production, verifying the package suffix. Select the TS922AID instead when the application is audio or needs rail-to-rail output swing; it costs more but delivers measurably better distortion and drive. For precision DC measurements needing microvolt offset, none of these fit - move to a precision op-amp family.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM358PT LM358APT LM2904PT (ROHM) LM2904 (SGMicro) TS922AID
Package TSSOP-8 (PT) TSSOP-8 (PT) - same TSSOP-8 (PT) - same 8-TSSOP-B - verify footprint SOP-8/TSSOP-8 - verify suffix TSSOP-8 (PT) - same
Brand STMicroelectronics STMicroelectronics STMicroelectronics ROHM Semiconductor SGMC (Sagna Microelectronics) ST
Amplifier Circuits 2 2 2 2 2 2
Amplifier Class General purpose, bipolar General purpose, bipolar General purpose, bipolar General purpose General purpose Audio-grade, rail-to-rail output
Output Configuration Single-ended Single-ended Single-ended Single-ended Single-ended Single-ended, rail-to-rail output

جیاکەرەوە سەرەکییەکان

  • Industrial/automotive temperature grade (بەراورد بەLM358PT)
  • Second-source availability with same MPN (بەراورد بەLM2904PT (ROHM))
  • Rugged bipolar architecture over CMOS alternatives (بەراورد بەTS922AID)

تێبینییەکانی دیزاین

The LM2904PT accepts up to 30 V total supply, but output swing never reaches the positive rail - the bipolar output stage leaves roughly 1 to 1.5 V of high-side headroom depending on load current. Budget this dropout when scaling sensor signals to an ADC input range, and never design the circuit so a valid signal requires output within about 1.5 V of VCC. On single supplies, decouple VCC (pin 8) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus bulk capacitance at the board level.

For the TSSOP-8 footprint, connect unused amplifier inputs to a defined potential - never leave them floating, or output chatter and supply-current modulation result. A common configuration ties the unused inverting input to its output (unity-gain buffer of a divider-set mid-rail). Keep input traces short and guard high-impedance nodes with ground ring where board leakage matters. Place the 100 nF decoupling capacitor directly between pin 8 and pin 4 with vias to the ground plane close to pin 4.

Two frequent errors with the LM2904 family: (1) substituting consumer-grade LM358 parts into sockets specified at industrial temperature grades - the LM2904 designation exists specifically for extended-range qualification, so keep the grade when the environment demands it. (2) Assuming rail-to-rail output on low-voltage single supplies - the output saturates well below VCC, so mid-rail bias circuits and signal scaling must leave high-side headroom. Also verify cross-brand footprints: ROHM's 8-TSSOP-B dimensions differ slightly from JEDEC TSSOP, so check the mechanical drawing before reusing land patterns.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

PartGenie lists the LM2904PT as ROHS3 Compliant. REACH, lead-free, halogen-free and conflict-minerals statuses should be confirmed on the STMicroelectronics product page.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm2904pt datasheet LM2904PT datasheet pdf LM2904PT pinout LM2904PT equivalent LM2904PT replacement LM2904PT cross reference LM2904PT vs LM358PT STMicroelectronics LM2904PT LM2904PT TSSOP-8 dual op amp LM2904PT price LM2904PT stock buy LM2904PT application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

STMicroelectronics LM2904PT LM358PT LM358APT ROHM Semiconductor SGMicro TS922AID LM2904 dual operational amplifier op-amp operational amplifier linear amplifier IC bipolar op-amp TSSOP-8 surface mount gain bandwidth product single-supply operation RoHS industrial signal conditioning automotive electronics active filter
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ