LM2904QPWRQ1 - Dual 26V 700kHz AEC-Q100 Op Amp | Texas Instruments
MPN: LM2904QPWRQ1 ✓ چالاکLM2904QPWRQ1 گشتی
An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is shaped by external feedback components. Op amps belong to the broader amplifier IC and analog-signal-processing hierarchy. They are widely used because a feedback network can set closed-loop gain, improve impedance characteristics, and enable stable implementations of common analog functions using resistors and capacitors.
The LM2904-Q1 family provides the established LM2904 operating characteristics in an automotive-qualified configuration. Key headline features include two amplifier channels, operation from a 26 V-rated supply, a 700 kHz gain-bandwidth product, and AEC-Q100 qualification. The manufacturer identifies the device as an industry-standard dual operational amplifier for automotive applications, where qualification supports controlled introduction into automotive electronic systems.
Its 700 kHz bandwidth makes the amplifier suitable for moderate-speed precision signal paths rather than high-frequency RF or video amplification. The dual architecture reduces package count when two independent gain or filtering stages are required. This is particularly useful in sensor interfaces, actuator drivers, battery-monitoring circuits, and automotive control modules where board area and component count affect reliability.
Typical applications include automotive sensor conditioning, low-side current measurement, transducer amplification, voltage buffering, and general-purpose analog signal processing. The high supply-voltage capability can simplify interfaces to automotive battery-derived rails, although designers must still observe the datasheet limits for input common-mode range, output swing, supply current, and thermal conditions.
A primary design consideration is that the TSSOP package has limited thermal dissipation capability. Follow the manufacturer datasheet for input and output voltage limits, common-mode behavior, electrical characteristics, and application guidance. Place bypassing capacitors close to the supply pins, preserve the recommended feedback topology, and verify common-mode and output-swing limits across the complete operating range.
This product page combines the manufacturer specification summary, automotive qualification information, package details, verified source links, application guidance, and a compatibility-oriented comparison framework. That engineering context helps distinguish the LM2904QPWRQ1 from lower-voltage modern op amps, higher-bandwidth alternatives, and non-automotive versions before a PCB or BOM decision is made.
جێگرەوەکانی جێگۆڕکێ بۆ LM2904QPWRQ1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904QPWRQ1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Operating Temperature Range, Slew Rate, Automotive Qualification.
LM2904BQPWRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904BAQPWRQ1
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2904QPWRG4Q1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904VQPWRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904PWRG3
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904QPWRQ1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Automotive Qualification | AEC-Q100 qualified |
| پاکێج | 8-pin TSSOP |
| جۆری دامەزراندن | Surface mount |
| Automotive Application | Yes |
| ESD Protection | Exceeds 500 V per MIL-STD-883, Method 3015; exceeds 200 V using machine model |
| دۆخی RoHS | Compliant |
| Moisture Sensitivity Level | MSL 1, 260 C/UNLIM |
ڕێکخستنی پینی LM2904QPWRQ1
| پین 1 | OUTA — Amplifier A output |
| پین 2 | IN A- — Amplifier A inverting input |
| پین 3 | IN A+ — Amplifier A non-inverting input |
| پین 4 | V- — Negative supply connection |
| پین 5 | IN B+ — Amplifier B non-inverting input |
| پین 6 | IN B- — Amplifier B inverting input |
| پین 7 | OUTB — Amplifier B output |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM2904QPWRQ1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Low-Side Current Measurement, Battery Monitoring and Line Conditioning, Actuator and Driver Signal Conditioning, Active Filtering and Noise Shaping, Instrumentation and Industrial Control.
Automotive Sensor Signal Conditioning
The LM2904QPWRQ1 fits automotive sensor interfaces because it combines two amplifier channels, a 26 V-rated supply, AEC-Q100 qualification, and a 700 kHz gain-bandwidth product in an 8-pin TSSOP package. Place one channel around a resistive sensor bridge or transducer and use the other channel for offset, filtering, or downstream buffering. The 700 kHz bandwidth is sufficient for many pressure, temperature, position, and level sensors without introducing high-speed design complexity. Validate the sensor output against the input common-mode range, check output swing at the worst-case supply and load, and use the second channel only when its offset and bias requirements remain compatible with the first.
پێشنیارکراو
Low-Side Current Measurement
The LM2904QPWRQ1 is appropriate for amplifying the small voltage produced by a low-side current-shunt amplifier because its 700 kHz gain-bandwidth product supports moderate-bandwidth feedback networks while the 26 V supply rating tolerates automotive-derived operating conditions. One channel can provide gain for the shunt voltage, and the second can buffer the result or drive an anti-alias filter. Component selection for the feedback resistors determines the actual noise, offset, and bandwidth trade-offs. Check the shunt common-mode voltage against the input limits, keep the feedback loop stable with the selected gain, and provide a low-resistance return path to minimize errors caused by supply and ground offsets.
پێشنیارکراو
Battery Monitoring and Line Conditioning
The LM2904QPWRQ1 can support battery-monitor front ends that must operate in electrically harsh environments and amplify a divided battery or load voltage. Its 26 V-rated supply capability and AEC-Q100 qualification make it relevant to automotive and industrial monitoring designs, while the dual channel allows one amplifier to condition the measurement and the other to provide buffering or threshold amplification. The 700 kHz gain-bandwidth product is more than adequate for slow battery-voltage changes and protection filtering. The design must account for transient voltage excursions, common-mode range, output saturation, and the thermal dissipation of the TSSOP package under the highest expected supply condition.
پێشنیارکراو
Actuator and Driver Signal Conditioning
The LM2904QPWRQ1 is useful in the analog control section of an automotive actuator or driver because two channels can condition a command signal and provide an intermediate buffer before a power stage. Its 26 V-rated supply and AEC-Q100 qualification align with automotive environment requirements, and its 700 kHz bandwidth handles control-loop signals well beyond common slow vehicle functions. A typical implementation uses one channel as a non-inverting gain stage with feedback resistors and the other as a unity-gain driver. Confirm that command transients stay within the input and output limits, add output isolation as required, and verify stability over the complete resistive and capacitive load range.
پێشنیارکراو
Active Filtering and Noise Shaping
The LM2904QPWRQ1 can implement first- or second-order active filters around sensor and control signals where a moderate 700 kHz closed-loop bandwidth is useful. The two amplifier channels permit stages such as an anti-alias filter followed by a buffer, or a non-inverting amplifier combined with a low-pass stage. Component tolerances determine the filter's gain accuracy and cutoff stability, while the op amp's offset and noise contribute to the output error. Prototype the selected topology with realistic source and load impedances, verify phase margin, and keep sensitive filter nodes away from switching-current paths to reduce conversion of common-mode disturbances into signal noise.
پێشنیارکراو
Instrumentation and Industrial Control
The LM2904QPWRQ1 can serve as a general-purpose building block in industrial instrumentation where two related analog stages must operate from a relatively high-voltage supply. Typical uses include amplifier input conditioning, reference buffering, gain stages around resistive bridges, and output drivers for slow control signals. Its 700 kHz gain-bandwidth product supports moderate-bandwidth loops, and the dual TSSOP package helps reduce component count. Choose resistor values that balance signal gain against bias-current and offset effects, maintain common-mode headroom, and verify operation at both supply extremes. Automotive qualification can add value in mobile equipment but does not remove the need to validate industrial EMC and environmental requirements.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2904QPWRQ1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2904BQPWRQ1 | LM2904BAQPWRQ1 | LM2904QPWRG4Q1 | LM2904VQPWRQ1 | LM2904PWR |
|---|---|---|---|---|---|---|
| Package | 8-pin TSSOP | 8-pin TSSOP - same footprint | 8-pin TSSOP - same footprint | 8-pin TSSOP - same footprint | 8-pin TSSOP - same footprint | 8-pin TSSOP - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Dual general-purpose operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Supply Rating | 26 V | 36 V | 36 V | 26 V | 26 V | 26 V |
| Automotive Qualification | AEC-Q100 qualified | AEC-Q100 qualified | AEC-Q100 qualified | Automotive-qualified LM2904-Q1 family ordering option | Automotive-qualified LM2904-Q1 family ordering option | Not identified as AEC-Q100 qualified |
| Generation | LM2904-Q1 | Next-generation LM2904B-Q1 | Next-generation LM2904BA-Q1 | LM2904-Q1 family ordering option | LM2904-Q1 family ordering option | Standard LM2904 family |
| Primary Application | Automotive general-purpose analog signal conditioning | Automotive general-purpose amplification | Automotive general-purpose amplification | Automotive general-purpose amplification | Automotive general-purpose amplification | General-purpose amplification |
| Channel Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
جیاکەرەوە سەرەکییەکان
- Established 26 V automotive-rated device with dual-channel integration (بەراورد بەLM2904PWR)
- Lower nominal supply rating can simplify compatibility with an established 26 V automotive interface (بەراورد بەLM2904BQPWRQ1)
- Dual general-purpose channels reduce package count for related analog stages (بەراورد بەTS952IPT)
- Qualified for automotive introduction with established LM2904 behavior (بەراورد بەLM2904BAQPWRQ1)
تێبینییەکانی دیزاین
Place the supply-bypass capacitor close to pins 4 and 8 and keep its current loop short. For signal integrity, route the two amplifier channels away from switching inductors, high-current return paths, and other sources of common-mode disturbance. Connect feedback components directly to their associated output and input pins, and avoid routing sensitive inputs beneath power-current paths. The compact 8-pin TSSOP layout leaves little room for long traces, so decoupling and grounding decisions should be made before placement is finalized.
Do not treat the 26 V supply rating as permission to place 26 V on the pins under every operating condition. Check absolute-maximum and recommended operating limits in the manufacturer datasheet, including input common-mode voltage, output swing, supply current, and behavior during power transitions. Also verify that the selected feedback gain remains stable with the intended source impedance and capacitive load. The 700 kHz gain-bandwidth product is adequate for many general-purpose stages but does not guarantee stability for every topology.
Estimated: at a 26 V supply and a hypothetical 1 mA total supply current, the maximum package dissipation attributable to the amplifier is approximately 26 mW, calculated as 26 V multiplied by 0.001 A. Actual dissipation, junction temperature, and board performance depend on supply voltage, quiescent current, load current, ambient temperature, PCB copper, and adjacent heat sources. Verify the final thermal condition using the manufacturer power-dissipation and maximum-junction-temperature guidance.
When using either channel in a high-gain configuration, calculate the noise gain at every frequency rather than considering only the signal gain. Place compensation or filtering components where their values interact predictably with the amplifier and source impedance. For slow automotive sensor signals, excessive bandwidth can admit more electrical noise than necessary; for faster signals, use the 700 kHz gain-bandwidth product to select a closed-loop bandwidth that preserves required phase margin.
زانیاری پابەندبوون
Texas Instruments identifies the LM2904-Q1 family as qualified to AEC-Q100 specifications. RoHS compliance is identified, while REACH, lead-free, halogen-free, and conflict-minerals status were not established from the cited product information.