Texas Instruments

LM324KAD - Quad Op-Amp, 1.2MHz, SOIC-14 | Texas Instruments

MPN: LM324KAD ✓ چالاک
3 V to 32 V Vdss 0.8 mA (typ) Id SOIC-14 (0.154 in, 3.90 mm width) Package
MOQ: 1 |

LM324KAD گشتی

The Texas Instruments LM324KAD is a quadruple general-purpose operational amplifier with four independent, high-gain, frequency-compensated amplifiers in a single 14-pin SOIC package. It operates from a single supply of 3V to 32V (or dual supplies of ±1.5V to ±16V), delivers a gain bandwidth product of 1.2 MHz, a slew rate of 0.5 V/µs, and includes 2kV ESD protection on all pins.

A general-purpose operational amplifier is a voltage amplifier with differential inputs and a single-ended output that, with external feedback networks, performs amplification, filtering, comparison, buffering, and mathematical operations. Op-amps sit at the foundation of the analog signal chain hierarchy: operational amplifier -> analog front end -> signal conditioning IC -> mixed-signal system. The LM324 family is the industry-reference quad op-amp, and the LM324KAD variant adds enhanced 2kV ESD robustness for assembly environments.

Key differentiating features include common-mode input voltage range that extends to ground (negative rail), enabling direct sensing of signals near 0V in single-supply systems; low supply-current drain of typically 0.8 mA per amplifier that is essentially independent of supply voltage; wide supply voltage tolerance for use across 5V, 12V, 24V industrial rails and ±15V analog rails; and four matched amplifiers sharing one bias network for reduced board space and matched thermal drift.

The internal architecture uses high-gain, internally frequency-compensated stages, so no external compensation capacitor is required at unity gain. The differential input stage with PNP input transistors allows inputs to swing to ground, a defining trait of the LM324 topology. Output stages source and sink current with the class-ab biasing characteristic of the family.

Typical applications include transducer amplifiers with ground-referenced sensors, DC gain blocks, active filters, comparators with hysteresis, summing and difference amplifiers, oscillator and multivibrator circuits, and general industrial instrumentation operating from single-ended 24V rails.

A key design consideration: the LM324 output cannot pull fully to the positive rail and its sink capability at low output voltages is limited, so a pulldown resistor or load-to-ground reference is needed for outputs near 0V. Margin of 1.5V to the positive supply is required for linear output swing.

This page adds information beyond the datasheet: verified distributor pricing context, drop-in alternative comparison (LM324AD, TS974IDT, MC3403DR, TL074), pinout table, practical design notes, and application-level selection guidance.

جێگرەوەکانی جێگۆڕکێ بۆ LM324KAD — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM324KAD (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate, Gain-Bandwidth Product, Operating Temperature Range, Mounting Type.

Texas Instruments
Package: 14-pin SOIC
Slew Rate: 0.5 V/µs
Gain-Bandwidth Product: 1.2 MHz
بەراوردکردن لەگەڵ LM324KAD →
Texas Instruments
Package: 14-pin SOIC (D)
Gain-Bandwidth Product: 1.2 MHz
Operating Temperature Range: 0 C to +70 C
بەراوردکردن لەگەڵ LM324KAD →
Texas Instruments
Package: 14-pin SOIC
Gain-Bandwidth Product: 1.2 MHz
بەراوردکردن لەگەڵ LM324KAD →
Texas Instruments
Slew Rate: 0.6 V/µs
Gain-Bandwidth Product: 1 MHz
Operating Temperature Range: −25 °C to 85 °C
بەراوردکردن لەگەڵ LM324KAD →
STMicroelectronics
Package: 14-pin SO package
Slew Rate: 4 V/us
Gain-Bandwidth Product: 12 MHz
بەراوردکردن لەگەڵ LM324KAD →

LM324AD

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14
4 circuits · 30 V · 1.2 MHz · 3 mV · Single supply or split supply · Internally compensated · True differential inputs · 14 pins

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324BIDR

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14
TI B-version: drop-in per datasheet, improved specs - supply 3V-36V vs 3V-32V, offset ±3 mV (B) / ±2 mV (BA)

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM224AD

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC-14
Quad general-purpose operational amplifier · 4 circuits · Four independent high-gain, frequency-compensated amplifiers · 1.2 MHz · 0.5 V/µs · 3 mV · 30 V · ±1.5 V to ±16 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TS974IDT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 SOIC-14
General-purpose operational amplifier · 4 circuits · Yes · 12 MHz · 4 V/us · 4 nV/Hz · 0.003% · ±1.35 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MC3403DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-14
Quad operational amplifier · 4 circuits · ±2.5 V to ±15 V · 30 V · 1 MHz · 0.6 V/µs · −25 °C to 85 °C · True differential inputs

✓ بەردەستە

$0.4102 / یەکە

بینینی داتاشیت →

TL074CDT

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14
JFET-input quad with higher slew rate and lower noise, but inputs do not operate at the negative rail - unsuitable for single-supply ground sensing

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM324KAD زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Channels 4 (quad)
Gain Bandwidth Product 1.2 MHz
Slew Rate 0.5 V/us
Supply Voltage (Single) 3 V to 32 V
Supply Voltage (Dual) +/-1.5 V to +/-16 V
Supply Current per Amplifier 0.8 mA (typ)
Common-Mode Input Range Includes ground (negative rail)
ESD Protection 2 kV (HBM)
پاکێج SOIC-14 (0.154 in, 3.90 mm width)
جۆری دامەزراندن Surface Mount
Internal Compensation Yes (unity-gain stable)

ڕێکخستنی پینی LM324KAD

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 VCC+ — Positive supply (or single supply)
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 OUT3 — Output of amplifier 3
پین 9 IN3- — Inverting input of amplifier 3
پین 10 IN3+ — Non-inverting input of amplifier 3
پین 11 VCC- — Negative supply or ground (single supply)
پین 12 IN4+ — Non-inverting input of amplifier 4
پین 13 IN4- — Inverting input of amplifier 4
پین 14 OUT4 — Output of amplifier 4

بەکارهێنانە باوەکان

LM324KAD گونجاوە بۆ 6 بەکارھێنانs: Transducer Amplifier with Ground-Referenced Sensors, Industrial 24V Signal Conditioning, DC Gain Blocks and Summing Amplifiers, Active Filters and Signal Conditioning Chains, Comparators with Hysteresis and Oscillators, Automotive and Battery-Powered Instrumentation.

🏭

Transducer Amplifier with Ground-Referenced Sensors

Single-supply sensor front ends are the classic LM324KAD use case because the input common-mode range includes ground: thermistors, photodiodes, strain-gauge bridges, and current-sense shunts referenced to 0V can connect directly to the non-inverting input without level shifting or a negative supply. Powered from a 5V or 24V rail at roughly 0.8 mA per amplifier, the device amplifies millivolt-level signals to ADC-friendly levels with a non-inverting gain set by two resistors. The 1.2 MHz bandwidth supports slow-changing physical signals (temperature, light, pressure) with ample margin. Design with the output headroom limitation in mind: keep amplified levels at least about 1.5V below the positive rail for linear swing, or add a pulldown resistor if near-zero outputs are required.

⚙️

Industrial 24V Signal Conditioning

In factory automation, the LM324KAD runs directly from a 24V single-ended rail within its 3V-32V single-supply range, conditioning 4-20 mA current loops, 0-10V sensor signals, and limit-comparator thresholds without an extra regulator stage. The 2kV ESD rating of the KA variant adds robustness for field-wired boards where harness transients reach connector pins. Four amplifiers per package implement transimpedance gain, active low-pass anti-alias filtering, window comparators, and reference buffering in a single SOIC-14, cutting board area and ensuring matched thermal drift across channels. Use input resistors to protect against voltages beyond the negative rail, and verify that fault conditions keep inputs within the stated common-mode range.

🔧

DC Gain Blocks and Summing Amplifiers

The LM324KAD serves as a quad DC gain block for level shifting, offset correction, and analog computation on single supplies. Internally frequency compensation makes it unity-gain stable with no external capacitor, so inverting summer and non-inverting gain stages need only resistors. The ground-including input range allows summing junctions referenced to the negative rail in low-side current sensing and weighted-average circuits. With four matched amplifiers sharing one package, thermal drift between channels is minimized, which matters in multi-channel scaling networks. Keep closed-loop bandwidth demands well inside the 1.2 MHz gain-bandwidth product - a gain of 100 settles to roughly 12 kHz - and bias unused channels as followers tied to a mid-supply reference to prevent parasitic oscillation.

📐

Active Filters and Signal Conditioning Chains

Multiple Sallen-Key and multiple-feedback filter stages fit economically in one LM324KAD: two second-order sections (four op-amps) implement a fourth-order low-pass anti-alias filter on a single 5V or 24V supply. Because the inputs sense down to ground, filters processing unipolar signals biased at 0V work without negative rails. The 1.2 MHz GBW supports corner frequencies up to tens of kilohertz with good Q accuracy; for cutoffs beyond about 50 kHz, Q enhancement and distortion grow as open-loop gain falls, so move to a wider-bandwidth device. Passives should be placed so feedback traces are short, and a 0.1 µF decoupling capacitor per package pin pair keeps supply impedance low across the audio and instrumentation band.

🔍

Comparators with Hysteresis and Oscillators

The LM324KAD doubles as a low-speed comparator and as the active element in relaxation oscillators, Schmitt triggers, and window detectors on single supplies. With the input range including ground and supply operation to 32V, thresholds can be placed anywhere in the 0V-to-near-rail span - useful for battery undervoltage locks, overcurrent flags, and level detection on 12V/24V systems. As an oscillator, the device drives RC astable and triangle-wave generators up to the low tens of kilohertz, limited by the 0.5 V/µs slew rate. Note that a general-purpose op-amp is not a dedicated comparator: recovery from saturation is slower, so for sub-microsecond response use a purpose-built comparator. Add positive-feedback hysteresis resistors to prevent chatter near slow-moving thresholds.

🔋

Automotive and Battery-Powered Instrumentation

Portable and battery-operated instruments exploit the LM324KAD's modest per-amplifier quiescent drain of typically 0.8 mA, which is essentially independent of supply voltage, preserving battery life in multi-channel designs. Operation from 3V means the device still works as the battery approaches end-of-charge on 3.3V and 5V single-cell systems, and direct ground sensing eliminates the charge-pump or negative regulator that ground-incompatible op-amps would require. Applications include handheld meter front ends, gas-detector amplifiers, and low-side current monitors. For duty-cycled designs, gate the supply with a switch rather than relying on a shutdown pin, since the LM324 family has no enable input; four channels powered together draw roughly 3.2 mA when active.

کورتەی بەرهەمە پێشنیارکراوەکان

MC3403DR Texas Instruments بەکارهێنراوە لە: Transducer Amplifier with Ground-Referenced Sensors, DC Gain Blocks and Summing Amplifiers, Comparators with Hysteresis and Oscillators TL074CDT Low-noise JFET quad for higher-bandwidth AC-coupled sensing بەکارهێنراوە لە: Transducer Amplifier with Ground-Referenced Sensors, Active Filters and Signal Conditioning Chains, Automotive and Battery-Powered Instrumentation LM324BIDR B-version upgrade with 3V-36V supply for 24V-rail margin بەکارهێنراوە لە: Industrial 24V Signal Conditioning, Comparators with Hysteresis and Oscillators TS974IDT STMicroelectronics بەکارهێنراوە لە: Industrial 24V Signal Conditioning, Active Filters and Signal Conditioning Chains, Automotive and Battery-Powered Instrumentation LM324AD Texas Instruments بەکارهێنراوە لە: DC Gain Blocks and Summing Amplifiers
What is the supply voltage range of LM324KAD?
The LM324KAD operates from a single supply of 3V to 32V, or from dual supplies of ±1.5V to ±16V. According to the Texas Instruments LM324KAD datasheet, operation from split supplies is possible if the difference between the two supplies is 3V to 32V and common-mode input remains within range. This wide span lets one device serve 5V logic-side circuits, 12V/24V industrial rails, and classic ±15V analog systems without redesign.
What is the difference between LM324KAD and standard LM324?
The LM324KAD is the enhanced-ESD variant of the classic LM324 quad op-amp: it adds 2kV ESD protection on all pins while keeping the same 1.2 MHz bandwidth, 0.5 V/µs slew rate, 3V-32V single-supply range, ground-sensing inputs, and identical SOIC-14 pinout. Functionally it is a drop-in replacement for any standard LM324 part in SOIC-14; the KA suffix signals the robustness upgrade for assembly-floor handling rather than a change in AC or DC performance.
LM324KAD vs TL074 - which is better?
The LM324KAD is better for single-supply, ground-referenced applications: its common-mode input range includes the negative rail, so it senses signals near 0V, and it runs from 3V up. The TL074 (JFET input) offers higher slew rate and lower noise but its inputs do not operate at the negative rail, making it unsuitable for single-supply sensing near ground. Choose LM324KAD for 5V/12V/24V industrial transducer circuits; choose TL074 for audio and AC-coupled circuits where input signals stay away from the negative rail.
LM324KAD vs MC3403 - which should I choose?
For most single-supply designs the LM324KAD is the safer choice. Both are quad general-purpose op-amps in SOIC-14 with ground-including input range, but the LM324KAD is specified down to 3V operation and carries 2kV ESD protection, which the MC3403 does not match at the low end. The MC3403 can be a drop-in footprint substitute when a second supplier is needed for sourcing resilience; verify its supply-voltage floor and offset specifications against your circuit before qualifying it.
Can TS974 replace LM324KAD?
Yes, the STMicroelectronics TS974 is a pin-to-pin drop-in replacement for the LM324KAD in SOIC-14. According to the ST datasheet, the TS974 is a quad rail-to-rail input/output op-amp designed as an improved LM324 equivalent, with the same pinout and footprint. It additionally offers rail-to-rail output swing, which the classic LM324 lacks. For new designs needing outputs closer to the rails, TS974 is an upgrade; for legacy-replacement, it is directly compatible.
What is the best drop-in replacement for LM324KAD?
The best drop-in replacements share the identical SOIC-14 pinout. From Texas Instruments, the LM324AD is the same part without the KA ESD enhancement, and the LM324B is TI's improved B-version, which the manufacturer states is a drop-in replacement for all versions of LM224, LM324, and LM2902 with better offset and supply range. Cross-brand, the ST TS974IDT and onsemi MC3403DR mount on the same footprint. All preserve pin numbering 1-14, so no PCB rework is required.
What is the best STMicroelectronics equivalent for LM324KAD?
The best ST equivalent is the TS974IDT, a quad operational amplifier in SOIC-14 that is pin-to-pin compatible with the LM324KAD. ST markets the TS974 explicitly as a rail-to-rail LM324-type device, so it keeps the same 14-pin assignment (OUT1, IN1-, IN1+, VCC, IN2+, IN2-, OUT2, OUT3, IN3-, IN3+, V-, IN4+, IN4-, OUT4). The TS934 is another ST quad option for lower-voltage operation. Verify output-drive requirements, since rail-to-rail output behavior differs slightly from the bipolar LM324 output stage.
Where can I download the LM324KAD datasheet PDF?
The LM324KAD datasheet PDF is available from Texas Instruments through its product folder on ti.com, and mirrored copies are hosted on datasheet archive sites such as alldatasheet.com (the TI document covers the LMx24, LMx24x, LM2902 families, 64 pages in the current revision). Request the exact document revision for your design record via the Request a Quote form on this page if you need a certified copy. Always design against the latest TI revision, since B-version specifications were added in later updates.
Where can I buy LM324KAD?
The LM324KAD can be sourced through the Request a Quote form on this page, which returns stock, quantity pricing, and lead time from XAIPART for production quantities. Distributors list the part as an active Texas Instruments product in SOIC-14 packaging. When requesting, specify the required package (SOIC-14, 3.90 mm width) and quantity so quotes match the correct suffix; several LM324 variants exist in different packages and the suffix must match your PCB footprint.
What is the lead time for LM324KAD?
The LM324KAD is a long-lived, high-volume commodity op-amp, so lead time is typically short when distributors hold stock; some listings confirm thousands of pieces in inventory. However, exact lead time changes with demand cycles, so submit the Request a Quote form on this page for a current commitment. Because the device is active and multi-sourced by equivalent parts, allocation risk is low compared with niche analog parts, and second sources exist on the same footprint.
What are the key specifications of LM324KAD engineers should know?
The LM324KAD provides four frequency-compensated op-amps with 1.2 MHz gain bandwidth product and 0.5 V/µs slew rate, powered from 3V to 32V single supply or ±1.5V to ±16V dual supplies. Per-amplifier supply current is typically 0.8 mA, the common-mode input range includes ground, all pins carry 2kV ESD protection, and the package is SOIC-14 surface mount. These numbers define it as a low-speed, low-power, single-supply general-purpose amplifier, not a precision or high-frequency part.
Is LM324KAD suitable for single-supply 5V operation?
Yes, the LM324KAD is well suited to 5V single-supply operation because its specified supply range starts at 3V and its input common-mode range includes ground, allowing sensors referenced to 0V to be amplified directly without a negative rail. Design within two limits: the output cannot swing rail-to-rail, so expect headroom of roughly 1.5V below the positive supply at moderate load, and keep closed-loop gain-bandwidth demands within the 1.2 MHz product for stable settling.
Why can LM324KAD outputs not reach 0V when sinking current?
The LM324 output stage sinks current through an NPN device that requires base drive from an internal current source, so near 0V output the device loses sink capability unless an external pulldown resistor (typically a few kilohms to ground) supplies the sink path. This is a documented family characteristic in the TI datasheet. If your circuit must output very close to 0V, add the pulldown resistor or choose a rail-to-rail output alternative such as the TS974IDT, which is footprint-compatible.
Is the LM324B a drop-in replacement for LM324KAD?
Yes. According to the Texas Instruments LM324 datasheet, the new LM324B and LM2902B versions are drop-in replacements for all versions of LM224, LM324, and LM2902, meaning the same SOIC-14 footprint and pinout with no PCB change required. The B version additionally improves specifications: supply range of 3V to 36V and lower input offset voltage (±3 mV for B, ±2 mV for BA). Upgrading to LM324B is a low-risk performance improvement for new builds of existing LM324 designs.
What is the bandwidth of LM324KAD and when is it insufficient?
The LM324KAD has a 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate. This supports audio-band gain blocks (for example, gain of 10 up to roughly 120 kHz) and slow industrial filtering, but it is insufficient for fast comparators, video signals, active filters above a few hundred kHz, or circuits needing slew beyond 0.5 V/µs. For those uses, select faster TI devices or the ST TL074-class JFET parts, which trade the ground-sensing input range for higher speed and lower noise.

داتای سەرچاوەی ئەندازیاری بۆ LM324KAD — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM324KAD when you need a low-cost, low-speed, single-supply quad op-amp that senses inputs at ground and runs from a 5V, 12V, or 24V rail, with the added 2kV ESD robustness for assembly and field environments. Choose the plain LM324AD when ESD handling is not a concern and cost dominates. Choose LM324BIDR when you want TI's improved B-version drop-in upgrade: 3V-36V supply and lower input offset with zero PCB change. Choose TS974IDT when outputs must reach both rails, accepting a narrower supply range. Choose MC3403DR when a second vendor footprint-compatible part is needed for supply resilience. Choose TL074-class JFET quads for audio or higher-speed AC-coupled circuits, never for ground-referenced single-supply sensing. All five share the SOIC-14 footprint, so qualification swaps require layout work only where drive requirements differ.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM324AD LM324BIDR TS974IDT MC3403DR
Package SOIC-14 SOIC-14 - same SOIC-14 - same SOIC-14 - same SOIC-14 - same
Brand Texas Instruments Texas Instruments Texas Instruments STMicroelectronics onsemi
Rail-to-Rail Output No (headroom ~1.5V below positive rail) No No Yes (rail-to-rail output) No

جیاکەرەوە سەرەکییەکان

  • 2kV ESD protection on all pins (بەراورد بەLM324AD)
  • Ground-sensing input on single supply (بەراورد بەTL074CDT)
  • Rail-to-rail output alternative exists on the same footprint (بەراورد بەTS974IDT)

تێبینییەکانی دیزاین

The most common LM324 error is expecting the output to reach 0V under load. The output sink transistor requires base drive from an internal current source, so below roughly a few hundred millivolts the device cannot sink load current. Add a pulldown resistor (typically 2 kOhm to 10 kOhm from the output to the negative rail) whenever the circuit must drive near 0V, or choose a rail-to-rail output part such as the pin-compatible TS974IDT. Similarly, plan about 1.5V of headroom below VCC for positive output swing.

Place a 0.1 µF ceramic decoupling capacitor within a few millimeters of pin 4 (VCC) and pin 11 (VCC-/GND), with a solid ground connection. Because the four amplifiers share one bias network, switching load transients on one channel can couple into the others; keep feedback loops short (under about 15 mm of trace) and route high-current or fast signals away from input pins. For single-supply designs, reference bias networks to a clean mid-supply or ground node rather than to a long shared ground spur.

Inputs of the LM324 family must not be pulled below the negative rail; PNP input-stage transistors can conduct abnormally (phase inversion) when an input goes below ground, latching outputs high. Add a series resistor (10 kOhm typical) on inputs connected to external connectors or inductive sensors to limit current under fault conditions. At closed-loop gains above 10, confirm the design bandwidth: with a 1.2 MHz gain-bandwidth product, a gain of 100 limits the usable bandwidth to roughly 12 kHz before slew-induced distortion appears at 0.5 V/µs.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status not stated in the retrieved distributor listings; confirm RoHS/REACH status on the TI product page before export-controlled builds.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM324KAD datasheet LM324KAD pinout LM324KAD datasheet pdf LM324KAD equivalent LM324KAD replacement LM324KAD cross reference LM324KAD price LM324KAD stock LM324KAD vs TL074 LM324 quad op-amp SOIC-14 pinout single supply quad op amp 1.2MHz LM324 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM324KAD LM324 LM324AD LM324B LM224 LM2902 TS974IDT MC3403DR TL074 STMicroelectronics onsemi operational amplifier quad op-amp general-purpose amplifier SOIC-14 small outline integrated circuit package surface mount gain bandwidth product slew rate single supply operation ESD protection analog signal conditioning transducer amplifier
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ