LM324KADRG4 - Quad 32V Op Amp with 2kV ESD | Texas Instruments
MPN: LM324KADRG4 ✓ چالاکLM324KADRG4 گشتی
The LM324 family combines a high-gain differential input stage with single-ended output stages designed for straightforward single-supply operation. According to the Texas Instruments LMx24, LMx24x, LMx24xx, LM2902, LM2902x, LM2902xx and LM2902xxx datasheet, operation from split supplies is also possible when the total supply difference is 3 V to 32 V. This flexibility supports legacy industrial control, sensor conditioning, audio preamplification, and low-frequency filter designs.
Key characteristics include four amplifiers in one package, a 3 V to 32 V supply range, low quiescent current of approximately 0.8 mA typical, and input common-mode voltage that includes ground. The LM324KADRG4 variant also carries 2 kV ESD protection according to its Texas Instruments product listing. The 14-pin SOIC footprint allows direct substitution with compatible LM324-family devices where electrical and temperature requirements are equivalent.
The internal architecture favors general-purpose precision over high-speed or low-noise performance. Each channel is internally frequency compensated, so no external compensation network is required for unity-gain voltage-follower or non-inverting amplifier configurations. Input bias and offset currents remain part of the error budget when the amplifier operates with high-impedance sensors.
Typical uses include four-channel sensor interfaces, low-frequency active filters, buffered ADC inputs, audio preamplifier stages, and general DC signal conditioning. Because all four channels share one package, ground-return and supply-bypass placement directly affect every amplifier and should follow the pinout and layout guidance in the manufacturer datasheet.
For new single-rail designs, first verify output swing, input common-mode limits, output-current capability, and noise at the intended signal bandwidth. The LM324 remains effective where its supply range and low quiescent current outweigh the lower noise, wider bandwidth, and faster slew rate available from modern precision operational amplifiers. This page also organizes practical substitution options, application guidance, and design checks that are not presented together on a standard distributor listing.
جێگرەوەکانی جێگۆڕکێ بۆ LM324KADRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM324KADRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Number of Channels, Slew Rate, Input Offset Voltage.
LM324ADR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324ADG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324AD
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324MX
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TL074CDR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324KADRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifiers | 4 |
| Amplifier Type | Single-ended, frequency-compensated operational amplifier |
| Supply Voltage Range, Single Supply | 3 V to 32 V |
| Supply Voltage Range, Split Supply | 3 V to 32 V total supply difference |
| Typical Supply Current | 0.8 mA |
| Input Common-Mode Voltage Range | Includes ground |
| ESD Protection | 2 kV |
| ژمارەی پینەکان | 14 |
| Package Type | 14-SOIC |
| جۆری دامەزراندن | Surface mount |
| External Compensation | Not required |
ڕێکخستنی پینی LM324KADRG4
| پین 1 | OUT1 — Amplifier 1 output |
| پین 2 | -IN1 — Amplifier 1 inverting input |
| پین 3 | +IN1 — Amplifier 1 non-inverting input |
| پین 4 | V- — Negative supply connection |
| پین 5 | +IN2 — Amplifier 2 non-inverting input |
| پین 6 | -IN2 — Amplifier 2 inverting input |
| پین 7 | OUT2 — Amplifier 2 output |
| پین 8 | OUT3 — Amplifier 3 output |
| پین 9 | -IN3 — Amplifier 3 inverting input |
| پین 10 | +IN3 — Amplifier 3 non-inverting input |
| پین 11 | V+ — Positive supply connection |
| پین 12 | +IN4 — Amplifier 4 non-inverting input |
| پین 13 | -IN4 — Amplifier 4 inverting input |
| پین 14 | OUT4 — Amplifier 4 output |
بەکارهێنانە باوەکان
LM324KADRG4 گونجاوە بۆ 6 بەکارھێنانs: Single-Supply Sensor Signal Conditioning, Buffered ADC Input Conditioning, Audio Preamplifier Stages, Active Low-Frequency Filters, Industrial Control Signal Buffers, Power-Supply Control and Feedback Loops.
Single-Supply Sensor Signal Conditioning
The LM324KADRG4 is appropriate for conditioning a resistive or low-current sensor referenced to ground because its 3 V to 32 V supply range supports 5 V, 12 V, and 24 V systems, while the common-mode input range includes ground. Each of the four channels can provide gain, inversion, or buffering before an ADC input. Input bias current and offset voltage set the accuracy floor for high-impedance dividers, so the sensor impedance and the required measurement resolution should be evaluated together. The low 0.8 mA typical supply-current drain also helps in battery-operated industrial instruments where every milliamp affects the duty cycle.
پێشنیارکراو
Buffered ADC Input Conditioning
Each LM324KADRG4 amplifier channel can provide the input impedance and signal gain needed between a sensor or divider and an analog-to-digital converter. Operating from a single supply simplifies level translation when the signal is ground-referenced, although the output must remain inside the ADC input range at the selected gain. Use the device when low bandwidth and low quiescent current matter more than the short settling time of a precision amplifier. Verify offset error, noise, and ADC acquisition requirements, because the four internal channels share supply and ground connections that can couple noise into each channel.
پێشنیارکراو
Audio Preamplifier Stages
The LM324KADRG4 can implement four low-frequency audio preamplifier or mixer channels in a single package. Its common-mode input range includes ground, which suits microphone and line-level signals referenced to the negative supply in split-supply systems. The internal frequency compensation removes the need for an external dominant-pole capacitor in conventional non-inverting and inverting stages. Bandwidth and slew-rate requirements should be checked against the highest audio frequency and the lowest gain used, because the general-purpose architecture prioritizes cost and supply flexibility over wide-band audio performance.
پێشنیارکراو
Active Low-Frequency Filters
Four independent LM324KADRG4 amplifiers can form second-order low-pass, high-pass, band-pass, or notch stages when higher-order filtering is required. The internal compensation supports standard closed-loop operation without an external compensation capacitor, and the 3 V to 32 V range accommodates both compact battery systems and industrial control panels. Component tolerances and amplifier open-loop gain directly affect filter cutoff accuracy and peaking. Prototype the complete filter, check the response against the required passband and stopband, and keep sensitive input nodes short and away from the supply bypass current path.
پێشنیارکراو
Industrial Control Signal Buffers
The LM324KADRG4 is a practical choice for buffering 4 mA-to-20 mA receiver outputs, potentiometer wipers, and low-level control signals in industrial equipment. Its four channels reduce package count, and the 24 V-compatible supply range supports legacy factory-control architectures. A precision resistor network can establish gain, while the amplifier supplies sufficient drive for downstream ADC or comparator inputs. Confirm output-current capability, output swing, and capacitive-load stability for the connected stage. A dedicated protection network should handle external transients rather than relying on the amplifier input alone.
پێشنیارکراو
Power-Supply Control and Feedback Loops
An LM324KADRG4 channel can amplify the error voltage in a linear regulator or supply-control loop, while additional channels monitor auxiliary conditions. The device's 3 V to 32 V supply range allows it to operate directly from many industrial rails, and its ground-inclusive input range simplifies feedback-divider design. Compensation must be chosen around the amplifier and control-loop transfer function rather than added as a generic capacitor. Verify loop stability under minimum and maximum load, check the output current needed by the feedback network, and keep compensation nodes away from switching or high-current supply paths.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM324KADRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM324ADR | LM324ADG | LM324AD | LM324MX | TL074 | LM2904 |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 | 4 |
جیاکەرەوە سەرەکییەکان
- Four amplifiers in one 14-SOIC package (بەراورد بەLM324MX)
- Documented low supply-current drain (بەراورد بەTL074)
- Wide single- and split-supply operating range (بەراورد بەLM2904)
تێبینییەکانی دیزاین
Route pin 11 directly to the positive supply bypass capacitor and pin 4 directly to the ground plane. Place the capacitor at the package rather than at the board power entry, and keep input and feedback traces away from the supply current path. The four amplifiers share the same supply pins, so supply-noise pickup can appear on every channel even when only one amplifier is active. Follow the manufacturer layout example and preserve a continuous ground return for pin 4.
Do not assume that a ground-referenced input is automatically safe at every gain and load. Verify the actual common-mode range, output swing, and output-current limits for the selected suffix and operating voltage. When substituting another LM324-family device, compare offset voltage, bias current, supply drain, bandwidth, and temperature grade; matching the footprint alone does not guarantee identical circuit behavior. Validate the final analog network at the minimum and maximum supply conditions used in production.
Keep high-impedance input and feedback nodes physically short because input bias current creates an error voltage across the source impedance. Use a low-value feedback resistor or an intermediate buffer when the sensor impedance is high, and keep the resistor network close to the amplifier pins. Avoid running parallel signal traces under noisy switching nodes or beside the supply bypass capacitor. For small-signal filtering, reserve the highest-impedance node for the lowest-frequency node.
زانیاری پابەندبوون
The manufacturer listing confirms a 2 kV ESD-protection configuration, but the available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.