Texas Instruments

LM358AN - Dual 1MHz Op Amp, 3-36V Single Supply | Texas Instruments

MPN: LM358AN ✓ چالاک
3 V to 36 V Vdss 20 nA typical Id PDIP-8, 8-pin plastic dual in-line (through-hole) Package
MOQ: 1 |

LM358AN گشتی

The Texas Instruments LM358AN is a dual, general-purpose operational amplifier providing two independent channels in an 8-pin PDIP (through-hole) package, with an A suffix indicating the lead-free (RoHS-compliant) finish. Each channel offers a 1.0 MHz unity-gain bandwidth, 0.3 V/us slew rate, and operation from a single 3 V to 36 V supply, making it the standard dual single-supply op amp for cost-sensitive analog signal conditioning.

An operational amplifier is an analog building block that amplifies the voltage difference between its two inputs. The LM358 belongs to the single-supply, rail-to-rail-input-capable general-purpose family: it is designed to run from one positive rail and a ground reference, so its input common-mode range extends from 0 V up to roughly 1.5 V below the positive supply. This topology sits at the bottom of the hierarchy of integrated circuit amplifiers: operational amplifier -> voltage-feedback amplifier -> amplifier IC -> analog semiconductor.

Key features include differential input stage trimming for low offset, internal frequency compensation so no external nulling or compensation components are required, and output-stage design that sources up to 40 mA and sinks up to 20 mA while staying within a few tens of millivolts of the supply rails. The two amplifiers are independent, allowing them to be used in separate signal chains or in differential and instrumentation configurations within a single package.

Technically, the LM358 uses a class-B output stage, so crossover distortion around 0 V output is a consideration in precision AC applications. The open-loop gain is typically 100 dB with a unity-gain bandwidth of 1 MHz, so closed-loop stability depends on keeping the feedback network noise-gain flat across the frequency range. Input bias current of roughly 20 nA and input offset voltage of a few millivolts make it appropriate for impedance levels above about 100 kOhm.

Typical applications include DC amplifier stages in sensor front ends, low-side current sensing with a shunt, active filters, comparators with reference inputs, audio mixers, and general instrumentation in industrial control and consumer equipment. The DIP-8 package is favored for through-hole assembly, prototype boards, and legacy repair where a surface-mount footprint would be impractical.

When designing with the LM358AN, keep input and output signals within the input common-mode range, and remember that at supply voltages below about 5 V the output swing limitations consume a larger share of the rail-to-rail span. For low-offset or low-noise instrumentation, add an external offset trim or select a higher-grade precision amplifier instead.

This page consolidates distributor availability, drop-in replacement options, and application-specific design guidance for the LM358AN into a single engineering reference that goes beyond a manufacturer datasheet.

جێگرەوەکانی جێگۆڕکێ بۆ LM358AN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358AN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Gain-Bandwidth Product, Supply Configuration, Mounting Type.

onsemi
Package: 8-PDIP, 0.300 inch (7.62 mm) pitch
Amplifier Type: General Purpose
Gain-Bandwidth Product: 1 MHz
بەراوردکردن لەگەڵ LM358AN →
onsemi
Package: 8-PDIP (DIP-8)
Amplifier Type: Standard (General Purpose)
Mounting Type: Through Hole
بەراوردکردن لەگەڵ LM358AN →
Texas Instruments
Package: 8-PDIP
Amplifier Type: General-purpose operational amplifier
Gain-Bandwidth Product: 700 kHz
بەراوردکردن لەگەڵ LM358AN →
Texas Instruments
Package: 8-PDIP
Gain-Bandwidth Product: 1 MHz
Supply Configuration: Single supply operation
Texas Instruments
Package: 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source
Supply Configuration: Single supply operation emphasized in the verified LM358 family description
بەراوردکردن لەگەڵ LM358AN →

LM358N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904P3

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8
General-purpose operational amplifier · 2 circuits · 26 V · 700 kHz · 8-PDIP · Through-hole · Operational amplifier · Operational amplifier

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 DIP-8
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 DIP-8
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

پەیوەندی بۆ نرخ

بینینی داتاشیت →

RC4558P

✅ جێگرەوەی ڕاستەوخۆ
📦 PDIP-8
Same 8-pin PDIP footprint and pinout as LM358; gain-bandwidth product is lower and the supply-voltage envelope differs, so bandwidth differs by roughly -50% but pinout matches

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM358AN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 2 (independent channels)
Amplifier Type General-purpose, internally frequency-compensated, single-supply operational amplifier
Supply Voltage Range (single supply) 3 V to 36 V
Maximum Total Supply Voltage 36 V
Input Common-Mode Voltage Range 0 V to (V+ minus 1.5 V)
Open-Loop Gain 100 dB minimum
Gain-Bandwidth Product 1.0 MHz
Slew Rate 0.3 V/us
Input Offset Voltage 2 mV typical, 3 mV maximum
Input Bias Current 20 nA typical
Input Offset Current 2 nA typical
Output Current 40 mA typical source, 20 mA typical sink
Output Voltage Swing Approximately 20 mV from each rail into 2 kOhm load
مەودای پلەی گەرمیی کارکردن 0 C to +70 C
پاکێج PDIP-8, 8-pin plastic dual in-line (through-hole)
Lead-Free Status Lead-free (A suffix), RoHS compliant
جۆری دامەزراندن Through-hole
Number of Outputs per IC 2

ڕێکخستنی پینی LM358AN

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 OUT A — Amplifier A output
پین 2 IN- A — Amplifier A inverting input
پین 3 IN+ A — Amplifier A non-inverting input
پین 4 V- — Negative supply / ground reference
پین 5 IN+ B — Amplifier B non-inverting input
پین 6 IN- B — Amplifier B inverting input
پین 7 OUT B — Amplifier B output
پین 8 V+ — Positive supply voltage

بەکارهێنانە باوەکان

LM358AN گونجاوە بۆ 6 بەکارھێنانs: Low-Side Current Sensing, Sensor Signal Conditioning, Audio Preamplifier and Mixer, Active Filters and Control Loops, Comparator and Threshold Detection, Industrial Control and Legacy Through-Hole Assemblies.

⚡

Low-Side Current Sensing

The LM358AN suits low-side shunt current sensing because its input common-mode range reaches down to 0 V, allowing the shunt to sit near the ground rail of a 5 V or 12 V system. With 1.0 MHz unity-gain bandwidth and 0.3 V/us slew rate it amplifies the millivolt-level shunt signal quickly enough for most motor and power-supply control loops, while the 20 nA typical input bias current keeps the error in a 100 milliohm shunt below 2 uV. The output stage sourcing 40 mA allows direct drive of the ADC input without a buffer, and the two channels can monitor shunt and temperature in the same package. For designs needing lower offset error, add an external trim or select a precision dual amplifier instead.

🏭

Sensor Signal Conditioning

For thermocouple, RTD, and resistive bridge front ends, the LM358AN provides the differential input stage needed to reject common-mode noise while operating from a single supply. Its 100 dB minimum open-loop gain and 1 MHz bandwidth support gains of 10 to 100 with ample phase margin in a single-pole configuration, and the differential input capability suits bridge excitation where the wanted signal is small relative to the 2.5 V or 5 V common-mode voltage. The 2 mV typical input offset voltage translates to roughly 0.2 C of error on an RTD at 100 ohms per degree, so critical temperature loops should be calibrated. The independent dual channels allow a second stage to be used for gain or filtering without adding another package.

🎧

Audio Preamplifier and Mixer

The LM358AN is widely used in low-cost audio preamplifier and mixing stages because both channels operate from a single supply while the output can swing to within about 20 mV of the positive rail into a 2 kOhm load. The 1 MHz gain-bandwidth product and 0.3 V/us slew rate provide ample bandwidth for audio band signals up to 20 kHz with modest closed-loop gain. Designers should note the class-B output stage, which introduces crossover distortion when the output idles near 0 V; biasing the stage slightly above ground or adding a small DC offset removes the audible effect. For low-noise headphone or line-level designs, a CMOS-input family such as the MCP6043-E/P offers lower distortion and lower noise.

🔧

Active Filters and Control Loops

The LM358AN is frequently used as the active element in second-order Sallen-Key and multiple-feedback filters because the internal frequency compensation removes the need for external nulling while the 1 MHz bandwidth keeps loop gain adequate at audio and low-kHz cutoff frequencies. Both channels can implement a matched pair, which is valuable for anti-alias and reconstruction filters where filter pairs must track closely. Care is needed with the input bias current: with 20 nA typical bias and 100 kOhm feedback resistors, that produces about 2 mV of DC error, so film resistors below 100 kOhm are preferred. Where the signal must swing near 0 V or the filter must be accurate at higher frequencies, a rail-to-rail CMOS dual amplifier is a better fit.

🖥️

Comparator and Threshold Detection

Although sold as an amplifier, the LM358AN is often used as an open-loop comparator for slow threshold detection because it operates from a single 3 V to 36 V supply with an input common-mode range reaching 0 V, so a sensor signal can be compared against a reference without a mid-supply bias. The 0.3 V/us slew rate and 1 MHz bandwidth give a response time on the order of tens of microseconds, adequate for over-voltage, over-temperature, and battery-low detection rather than for fast protection loops. Because the output is push-pull, the output stays high or low rather than drifting, though the crossover dead zone near 0 V should be avoided by offsetting the reference. For faster or more precise decisions, a dedicated comparator IC is the appropriate choice.

🏭

Industrial Control and Legacy Through-Hole Assemblies

The 8-pin PDIP package of the LM358AN is still widely used in industrial control boards, motor drive auxiliaries, and instrumentation where through-hole assembly is preferred for repairability and mechanical robustness. Because the two amplifiers are independent, one channel can close a slow current or voltage regulation loop while the other provides an output buffer for a reference or actuator driver. The 40 mA source capability is adequate for driving logic-level inputs and opto-isolator LED bias resistors directly, reducing component count. The 0 C to +70 C rating suits ambient-controlled cabinets, and the A suffix provides the lead-free finish required for RoHS-compliant industrial equipment. For extended temperature cabinets, the pin-compatible LM2904P3 covers -40 C to +125 C.

What is the LM358AN and what are its key specifications?
The LM358AN is a dual general-purpose operational amplifier in an 8-pin PDIP package from Texas Instruments, with each channel offering a 1.0 MHz unity-gain bandwidth, 0.3 V/us slew rate, and operation from a single 3 V to 36 V supply. According to the Texas Instruments LM358/LM358A datasheet, the open-loop gain is 100 dB minimum, input bias current is typically 20 nA, and input offset voltage is 2 mV typical / 3 mV maximum. The two amplifiers in the package are electrically independent, so they can be used in two separate signal chains or in a differential and instrumentation configuration.
What is the pinout of the LM358AN?
The LM358AN is a standard 8-pin dual op-amp pinout: pin 1 is amplifier A output, pin 2 amplifier A inverting input, pin 3 amplifier A non-inverting input, pin 4 is ground, pin 5 amplifier B non-inverting input, pin 6 amplifier B inverting input, pin 7 amplifier B output, and pin 8 is the positive supply. Pin 1 is marked by the notch or dot on the package body. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks or socket wiring.
Where can I download the LM358AN datasheet PDF?
The manufacturer datasheet for the LM358/LM358A family is available from the Texas Instruments product documentation server, and distributor-hosted copies are published by Fairchild Semiconductor, STMicroelectronics, NXP Semiconductors, and onsemi. The document covers the LM2904, LM358/LM358A, and LM258/LM258A descriptions, including the two independent, high-gain, internally frequency-compensated operational amplifiers designed to operate from a single power supply over a wide range of voltages. Request a Quote on this page and the datasheet link can be provided with your order confirmation.
What does the A suffix mean on LM358AN?
The A suffix in LM358AN indicates the lead-free, RoHS-compliant version of the device, while N designates the standard PDIP-8 package code used by the LM358N. For example, the LM358N from STMicroelectronics and onsemi is listed as an 8-pin DIP while the LM358AN from Texas Instruments is listed as an 8-PDIP, both sharing the same dual-op-amp footprint and pin assignment. The distinction matters for RoHS documentation in new designs rather than for the electrical connection.
Is the LM358AN suitable for single 5V supply operation?
Yes, the LM358AN is designed to work from a single supply of 3 V to 36 V, which makes it a natural fit for 5 V systems built around microcontrollers. Note that at 5 V the input common-mode range extends from 0 V to about 3.5 V, and the output can typically swing only from roughly 0.2 V to 4.8 V into a 2 kOhm load, so headroom for large signal swings is limited at low supply voltages.
What is the difference between the LM358AN and the LM2904P3?
The main difference is temperature range and supply rating: the LM2904P3 is rated from -40 C to +125 C for industrial and automotive use, while the LM358AN is specified from 0 C to +70 C for commercial applications. Both are dual internally compensated op amps with a 1 MHz gain-bandwidth product in an 8-pin PDIP footprint with identical pin numbering, so the LM2904P3 can be used as a drop-in replacement where extended temperature operation is required.
What are the best drop-in replacements for the LM358AN?
The closest drop-in replacements are the LM358N from Texas Instruments, STMicroelectronics, and onsemi, all of which share the 8-pin PDIP footprint and identical pinout with the same 1 MHz bandwidth and 3 V to 36 V supply capability. The LM2904P3 is the pin-compatible choice when a -40 C to +125 C temperature range is needed. For the RC4558, the pinout matches but supply-voltage and bandwidth details differ, so verify the operating envelope before substitution.
Can I replace the LM358AN with the LM358N?
Yes, the LM358N is functionally and pin compatible with the LM358AN, differing mainly in the lead-free marking convention of the part number. Both are 8-pin PDIP dual op amps with 1.0 MHz unity-gain bandwidth, 0.3 V/us slew rate, and 3 V to 36 V single-supply operation. Confirm that your production documentation accepts the non-A-suffix ordering code if RoHS reporting must match the original component.
When should I choose the LM358AN over a precision amplifier?
Choose the LM358AN when the signal path needs moderate gain-bandwidth product, single-supply operation, and low cost, such as in current-sense amplifiers, active filters, or audio preamplifier stages. Choose a precision or rail-to-rail amplifier instead when input offset voltage below 1 mV, output swing closer to the rails, or input bias current in the femtoamp range is required, since the LM358AN's 2 mV typical offset and 20 nA bias current set the achievable accuracy.
Is the LM358AN still suitable for new designs?
Yes, the LM358AN remains a widely used general-purpose dual op amp for new designs because it runs from a single 3 V to 36 V supply with no external compensation or nulling parts required. For new precision or low-voltage designs, modern families offer lower offset, better rail-to-rail behavior, and lower noise, but the LM358AN remains appropriate where cost, availability, and through-hole DIP assembly dominate the design decision.
How much output current can the LM358AN source and sink?
The LM358AN output stage can source up to approximately 40 mA and sink approximately 20 mA according to the manufacturer datasheet typical characteristics. The ability to source more than it sinks comes from the push-pull output topology with a class-B bias scheme. Keep the load within these limits and observe the maximum output swing of roughly 20 mV from each rail at a 2 kOhm load, since the swing degrades at lighter loads.
Why does the LM358AN show crossover distortion near 0 V output?
The LM358AN uses a class-B output stage, so both output transistors are off near 0 V and a dead zone of a few tens of millivolts appears around the crossover point. This distortion is inaudible in most instrumentation and control loops but can be heard in high-fidelity audio paths. Solutions include adding a small output bias network, choosing a rail-to-rail CMOS input amplifier such as the MCP6043-E/P, or shifting the signal operating point so the output does not idle near 0 V.
Where can I buy the LM358AN and what is the price?
The LM358AN is a broadly stocked dual op amp offered by multiple authorized distributors and manufacturers, including Texas Instruments, STMicroelectronics, onsemi, Fairchild, and NXP Semiconductors. Live pricing, stock levels, and lead time are maintained on this product page, and the Request a Quote form on this page returns a current quotation for the exact MPN, including lead time and packaging options.
What is the lead time for the LM358AN?
Lead time for the LM358AN varies by manufacturer, package variant, and current inventory, and the same MPN is produced by several suppliers. Submit the MPN through the Request a Quote form on this page to receive the current lead time and stock confirmation for the package and quantity you need. For design stability, note that the non-suffix versions such as the LM358N and the LM2904P3 are equally available and pin compatible.
Is the LM358AN RoHS compliant and suitable for automotive use?
The A suffix of LM358AN denotes the lead-free, RoHS-compliant ordering code, so it is appropriate for RoHS-restricted consumer and industrial equipment. It is not an AEC-Q100 qualified automotive part; for automotive temperature requirements of -40 C to +125 C, use the pin-compatible LM2904P3 in the same 8-pin PDIP footprint.
How should I decouple and lay out the LM358AN on a PCB?
Decouple the positive supply pin 8 with a 100 nF ceramic capacitor placed as close to the pin as possible, and add a bulk electrolytic or ceramic capacitor of a few microfarad on the rail to handle transient current. Keep the feedback resistors close to the input pins to minimize parasitic capacitance that can destabilize the 1 MHz amplifier, and route the ground return from pin 4 directly to the ground plane to avoid shared return paths with output current.

داتای سەرچاوەی ئەندازیاری بۆ LM358AN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM358AN when you need a low-cost, single-supply dual amplifier in a through-hole package for general-purpose signal conditioning, current sensing, filtering, or threshold detection at 3 V to 36 V. Choose the LM358N when you need an identical device but with a non-lead-free ordering code acceptable to your documentation process, or when dual-sourcing across Texas Instruments, STMicroelectronics, and onsemi. Choose the LM2904P3 when the enclosure reaches -40 C to +125 C and the extra offset tolerance is acceptable. Choose the RC4558P only when cost dominates and the halved bandwidth is acceptable for your signal. If your design needs offset below 1 mV, rail-to-rail output swing, or sub-nA bias current, a precision or CMOS dual amplifier such as the TLV2462ID or MCP6043-E/P is a better fit even though it is not a pin-compatible DIP-8 substitute. For new PCB designs, prefer the surface-mount LM358DR form factor if you are not constrained to through-hole assembly.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM358N LM2904P3 LM358N LM358N RC4558P
Package PDIP-8 (through-hole, lead-free A suffix) PDIP-8 (through-hole) - same footprint PDIP-8 (through-hole) - same footprint DIP-8 (STMicroelectronics) - same footprint DIP-8 (onsemi) - same footprint PDIP-8 - same footprint
Brand Texas Instruments Texas Instruments onsemi STMicroelectronics onsemi Texas Instruments
Number of Amplifiers 2 2 2 2 2 2
Internal Frequency Compensation Yes, no external nulling required Yes Yes Yes Yes Yes

جیاکەرەوە سەرەکییەکان

  • Pin-compatible sourcing from multiple manufacturers on the same 8-pin PDIP footprint (بەراورد بەLM358N)
  • Extended temperature drop-in for industrial and automotive environments (بەراورد بەLM2904P3)
  • Lead-free ordering code for RoHS-compliant new production (بەراورد بەLM358N)
  • Two independent channels in one package with class-B push-pull output (بەراورد بەRC4558P)

تێبینییەکانی دیزاین

Estimated: with a 12 V supply, 5 V output, and 20 mA load, the LM358AN dissipates roughly (12 V - 5 V) x 20 mA = 140 mW, which is negligible for the PDIP-8 thermal design. Estimated: at a 36 V supply with 20 mA output current and 5 V output, dissipation rises to about (36 V - 5 V) x 20 mA = 620 mW, still within the package capability but worth checking against the board ambient. Keep a 100 nF ceramic decoupling capacitor at pin 8 and connect pin 4 directly to the ground plane to prevent supply ripple from modulating the output.

Place the input, feedback, and decoupling components adjacent to the DIP-8 pins to minimize parasitic capacitance on the summing node. Because the amplifier is unity-gain stable at 1 MHz, keep the feedback resistors physically short and avoid long traces between pins 2 and 1 (channel A) and pins 6 and 7 (channel B). For through-hole boards, use a socket when field replacement is likely, and ensure the socket pin-1 orientation matches the package marking so the pinout table can be applied directly.

Do not allow input signals to exceed the common-mode range of 0 V to V+ minus 1.5 V; exceeding it can cause phase reversal and latch-up-like behavior in the input stage, particularly on the negative rail during power-up. Also remember that the class-B output stage introduces a crossover dead zone around 0 V, and that at 5 V supply the output cannot reach either rail. Avoid forward-biasing the input protection diodes by ensuring the input stays within the supply rails during power sequencing.

The 20 nA typical input bias current multiplied by a 1 MOhm feedback resistor creates a 20 mV DC error, so prefer feedback values of 100 kOhm or less for high-gain stages. If higher impedances are unavoidable, add a bias compensation resistor equal to the parallel combination of the input resistors on the non-inverting input. For AC-only applications, place small capacitors across the feedback resistors to stabilize noise gain when the source impedance is high.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Qualified
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The A suffix in LM358AN denotes the lead-free, RoHS-compliant ordering code. The device is a commercial-temperature (0 C to +70 C) part and is not AEC-Q100 qualified; use the pin-compatible LM2904P3 for automotive temperature requirements. REACH, halogen-free status, and conflict-minerals declarations are not published on the manufacturer product pages reviewed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm358an datasheet lm358an pinout lm358an nopb lm358an datasheet pdf lm358an op amp lm358an nopb datasheet LM358AN equivalent LM358AN drop-in replacement LM358AN vs LM2904P3 LM358AN DIP-8 footprint LM358AN single supply 3V to 36V LM358AN current sensing amplifier Texas Instruments LM358AN LM358AN price and stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM358AN LM358N LM2904P3 RC4558P STMicroelectronics onsemi Fairchild Semiconductor NXP Semiconductors operational amplifier voltage-feedback amplifier dual op amp single-supply amplifier gain-bandwidth product slew rate input offset voltage input bias current common-mode voltage range open-loop gain class-B output stage internally frequency-compensated PDIP-8 DIP-8 surface mount RoHS AEC-Q100 LEAD-FREE current-sense amplifier Sallen-Key filter
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ