Texas Instruments

LM358APWRG4 - Dual 700 kHz Op Amp | Texas Instruments

MPN: LM358APWRG4 ✓ چالاک
5 V Vdss 0.7 mA typical Id TSSOP-8, green plastic Package
MOQ: 1 |

LM358APWRG4 گشتی

The Texas Instruments LM358APWRG4 is a dual general-purpose operational amplifier in an 8-pin TSSOP package. Each amplifier provides a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 80 dB common-mode rejection, and 2 mV input offset voltage, making the device suitable for general signal conditioning from a single 5 V supply.

An operational amplifier is an analog amplifier that uses very high open-loop gain to increase the voltage applied across an impedance connected to its inverting input. With external feedback, a practical LM358 stage can operate as a voltage amplifier, current-to-voltage converter, comparator, or active filter. The LM358 family belongs to the broader operational amplifier and analog signal-processing IC categories.

The LM358APWRG4 uses a 0.7 mA typical supply-current drain, supports single or dual supplies, and provides a common-mode input range that includes the ground rail. Its 0.3 V/us slew rate limits large-signal bandwidth, while the 80 dB CMRR helps reject common-mode noise. These characteristics make it appropriate for transducers, feedback loops, sensor interfaces, audio paths, and low-to-moderate-frequency control systems.

The device operates from 5 V in the characterized operating condition and belongs to the 26 V maximum supply-voltage class of the LM358 family. Its operating temperature range is 0 C to 70 C for this ordering code. The LM358 dual-amplifier configuration allows both channels to share one package while preserving independent inputs and outputs, reducing board area compared with two single-amplifier packages.

Common applications include buffering sensor outputs, amplifying low-level signals, summing analog signals, driving ADC input stages, implementing active filters, and providing feedback around analog control loops. Because the LM358 output stage is not rail-to-rail, output swing limits and input common-mode restrictions must be checked against the actual signal range before layout is finalized.

Place input, feedback, and bypass capacitors close to their associated pins, and route sensitive input traces away from switching nodes and high-current paths. Verify stability with the manufacturer guidance for capacitive loads, because the 0.3 V/us slew rate and output-capacitance limits can affect transient response. The TSSOP-8 package also requires careful thermal assessment when both channels operate continuously near the supply rail.

This page combines the device specifications, verified sourcing records, application engineering guidance, and same-footprint replacement analysis to support faster component selection and PCB planning.

جێگرەوەکانی جێگۆڕکێ بۆ LM358APWRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358APWRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Mounting Type, Gain-Bandwidth Product, Slew Rate.

Texas Instruments
Package: 8-pin TSSOP, 4.40 mm width
بەراوردکردن لەگەڵ LM358APWRG4 →
Texas Instruments
Package: 8-pin PDIP
Mounting Type: Through-hole
بەراوردکردن لەگەڵ LM358APWRG4 →
STMicroelectronics
Amplifier Type: Standard general-purpose operational amplifier
Package: 8-TSSOP
بەراوردکردن لەگەڵ LM358APWRG4 →
Texas Instruments
Amplifier Type: General Purpose
Package: 8-TSSOP
Gain-Bandwidth Product: 700 kHz typical
بەراوردکردن لەگەڵ LM358APWRG4 →

LM358APWR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 TSSOP-8
Same LM358 dual-amplifier family and TSSOP-8 footprint; ordering-suffix and RoHS documentation must be confirmed

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM358APWE4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 TSSOP-8
General Purpose · 2 circuits · 8-TSSOP · 4.40 mm · Surface Mount · Gull Wing · 8 terminals · Tube

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358APT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
STMicroelectronics
📦 TSSOP-8
Standard general-purpose operational amplifier · 2 channels · 2 circuits · 8-TSSOP · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358APG4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 TSSOP-8
Dual operational amplifier · 2 circuits · General-purpose amplifier · 8-pin PDIP · Through-hole · 0°C to 70°C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358APWRG4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 TSSOP-8
Dual general-purpose operational amplifier · 2 circuits · 700 kHz · 0.3 V/us · 5 V · 26 V · 0.7 mA typical · -0.2 uA typical

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358APWRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type Dual general-purpose operational amplifier
Number of Circuits 2 circuits
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/us
Typical Supply Voltage 5 V
Maximum Supply Voltage 26 V
Supply Current Drain 0.7 mA typical
Input Bias Current -0.2 uA typical
Input Offset Voltage 2 mV
Common-Mode Rejection Ratio 80 dB
Common-Mode Input Voltage Range Includes the ground rail
Supply Configuration Single or dual supply
مەودای پلەی گەرمیی کارکردن 0 C to 70 C
Package Type TSSOP-8, green plastic
جۆری دامەزراندن Surface mount
دۆخی RoHS RoHS-compliant
Lead-Free Status Lead-free
Package Pin Count 8 pins

ڕێنمایی ڕێکخستنی پینی LM358APWRG4 8 pins

ڕێکخستنی پین بۆ LM358APWRG4 (پاکێجی 8 pins). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8 pins بۆ LM358APWRG4

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM358APWRG4.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LM358APWRG4 گونجاوە بۆ 6 بەکارھێنانs: Sensor Signal Conditioning, Audio Preamplifier and Mixer, Active Low-Pass Filter, ADC Front-End Amplification, Current-to-Voltage Conversion, Industrial Control Feedback.

🧩

Sensor Signal Conditioning

The LM358APWRG4 suits resistive-sensor and transducer interfaces that operate from a single 5 V rail. Its common-mode input range includes ground, allowing signals near 0 V to be amplified without a negative supply, while the 80 dB CMRR helps reject common-mode interference coupled into sensor wiring. A noninverting stage can provide gain with the resistor network selected for the intended signal range. The 2 mV input offset and 0.7 mA typical supply-current drain are important considerations for high-impedance sources, and the 0.3 V/us slew rate should be checked against the required transient response.

🎧

Audio Preamplifier and Mixer

The dual LM358APWRG4 provides two independent amplifier channels for microphone preamplification, summing, or a small audio mixing stage. A 700 kHz gain-bandwidth product covers audio-band signals with ample bandwidth margin, and the 0.3 V/us slew rate supports moderate-amplitude waveforms. One channel can amplify the incoming audio signal while the other implements summing or active feedback. Because the output stage does not swing fully to the supply rails, headroom must be maintained for the largest peak voltage, and input bias current should be compared with the source impedance to avoid avoidable DC error.

🔧

Active Low-Pass Filter

The LM358APWRG4 can implement first- or higher-order active filters when the signal bandwidth remains well below its 700 kHz gain-bandwidth product. Its 80 dB CMRR can improve rejection of interference coupled equally into both inputs, while the two channels allow a second-order section or a separate buffer. Component tolerances in the feedback and gain-setting resistors establish the actual cutoff accuracy and Q. Stability with the intended source and load impedances should be checked, particularly when driving capacitive cable or filter loads that approach the amplifier's capacitive-load limit.

📊

ADC Front-End Amplification

The LM358APWRG4 is useful as a gain or buffer stage ahead of an analog-to-digital converter when the converter input can be driven from a single supply. Its 700 kHz bandwidth accommodates many moderate-rate conversion systems, and the two amplifiers can provide independent gain and driver functions. The 2 mV input offset contributes to the system error budget, so gains near 1 may require offset correction or calibration. Output swing limitations must also be checked against the ADC input range, particularly for unipolar systems whose conversion codes depend on approaching the upper rail.

💡

Current-to-Voltage Conversion

A transimpedance stage built with the LM358APWRG4 can convert a current from a photodiode, sensor, or instrumentation loop into a measurable voltage. Using one amplifier as the transimpedance element and the other as an optional buffer or gain stage can reduce the number of packages on a measurement board. The 0.7 mA typical supply-current drain is favorable for low-power instrumentation, but the input bias current of -0.2 uA and the 2 mV offset must be compared with the expected photocurrent and target resolution. Feedback resistor and parasitic-capacitance selection determine bandwidth and stability.

🏭

Industrial Control Feedback

The LM358APWRG4 can provide error amplification in a low-frequency industrial control loop, such as a temperature or slow-position feedback path. Its 80 dB CMRR is useful when the feedback signal is referenced to a noisy common-mode environment, and the 0 to 70 C operating range matches many ambient indoor conditions. The 0.3 V/us slew rate limits loop correction for fast transients, so control bandwidth must remain conservative. Compensation components should be derived from the actual forward-path gain and load, and the output-stage saturation limits must be included in the loop design.

What are the key specifications of LM358APWRG4?
The LM358APWRG4 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 80 dB CMRR, 2 mV input offset voltage, and 0.7 mA typical supply-current drain. It uses an 8-pin TSSOP package and operates from a single 5 V supply in the characterized operating condition. Texas Instruments lists the device as a standard instrumentation or buffer amplifier with two independent channels.
What is the operating voltage of LM358APWRG4?
The LM358APWRG4 is characterized at a 5 V supply, and the LM358 family supports single or dual supply operation. The family specification lists a maximum supply voltage of 26 V. Because the output stage is not rail-to-rail, the usable input and output ranges are more restrictive than the absolute supply limits, so check the manufacturer datasheet before operating near either rail.
Where can I download the LM358APWRG4 datasheet PDF?
The LM358APWRG4 manufacturer datasheet is available through Texas Instruments and the indexed document listings on alldatasheet. The indexed copy identifies the document as the Industry-Standard Dual Operational Amplifiers datasheet and lists 66 pages. Use the pin-description and electrical-characteristics tables in that document when assigning PCB tracks and checking worst-case operating conditions.
Where can I find the LM358APWRG4 pinout?
The LM358APWRG4 uses an 8-pin TSSOP configuration with two operational amplifiers and one shared supply connection arrangement. The manufacturer datasheet contains the authoritative pin-description table and package drawings. Use those tables rather than inferring connections from another LM358 package, because SOIC-8, TSSOP-8, and DIP-8 variants may use different physical pin numbering conventions.
Is LM358APWRG4 suitable for a single 5 V supply?
Yes, the LM358APWRG4 supports single-supply operation and is characterized at 5 V. Its common-mode input range includes ground, making it practical for sensors whose outputs sit near 0 V. The output swing does not reach the positive supply rail, so leave headroom for the largest required output and use gain-shaping feedback if near-rail operation is necessary.
What can replace the LM358APWRG4?
The closest same-footprint replacement is another Texas Instruments LM358 ordering code specified in the 8-pin TSSOP package, provided its temperature grade and suffix requirements match the original design. A component in SOIC-8 or DIP-8 is not a physical drop-in replacement for a TSSOP-8 PCB. Confirm channel pinout, supply rating, temperature grade, and packaging before approving any substitute.
Is LM358APWRG4 the same as LM358APWR?
The LM358APWRG4 and LM358APWR are closely related Texas Instruments LM358 order codes, but a purchasing decision should confirm the exact suffix, temperature grade, packaging configuration, and RoHS documentation. Because both can exist in the same TSSOP family, the footprint may match while orderable configuration and commercial terms differ. Review the manufacturer ordering table before treating them as interchangeable.
What is the best replacement for LM358APWRG4 in an 8-pin TSSOP design?
The best replacement is a pin-compatible dual op amp in the same 8-pin TSSOP footprint whose input, output, supply, common-mode, and stability characteristics satisfy the original circuit. The LM358 family offers the closest functional match, while cross-brand substitutes require verified pinout and electrical equivalence. This page identifies no cross-brand TSSOP-8 candidate with complete drop-in confirmation in the available cross-reference records.
When should I choose LM358APWRG4 instead of a rail-to-rail op amp?
Choose the LM358APWRG4 when the signal and output ranges remain within its common-mode and swing limits and a low-cost, widely supported dual amplifier is preferred. It offers a 700 kHz gain-bandwidth product, 80 dB CMRR, and 0.7 mA typical supply-current drain. Select a rail-to-rail amplifier instead when inputs and outputs must operate very close to the supply rails.
Is LM358APWRG4 suitable for audio preamplifier applications?
Yes, the LM358APWRG4 can serve as a general-purpose audio preamplifier when its input and output ranges remain within the usable swing limits. Its 80 dB CMRR helps reject common-mode interference, while the 0.3 V/us slew rate is adequate for many low-to-moderate-bandwidth audio stages. Use suitable input and feedback networks and follow the manufacturer's guidance for capacitive loading.
Where to buy LM358APWRG4 online?
The LM358APWRG4 is listed for procurement through the manufacturer's authorized distribution network and specialist electronic component suppliers. Current commercial terms, stock, minimum order quantity, and lead time are handled through the Request a Quote form on this page. Provide the exact suffix LM358APWRG4 when requesting a quotation to avoid confusion with other LM358 package or temperature-grade options.
What is the price of LM358APWRG4?
Pricing for LM358APWRG4 depends on order quantity, supplier inventory, and the exact ordering configuration. Use the Request a Quote form on this page for current commercial terms. The available indexed listing shows a starting-price reference rather than a complete quantity-break table, so it is not represented as fixed tier pricing in the structured price data for this page.
What is the lead time for LM358APWRG4?
The current lead time depends on supplier inventory, scheduled production, and the quantity ordered. Submit an LM358APWRG4 request through the Request a Quote form on this page to obtain a current commitment. For production planning, provide your required quantity, target delivery date, and acceptable packaging arrangement so scheduling can be evaluated accurately.
Is LM358APWRG4 in stock?
Stock availability for LM358APWRG4 changes with supplier inventory and replenishment cycles. The indexed distributor records identify the part as purchasable, but they do not establish a fixed quantity available for every order. Use the Request a Quote form on this page for a current availability confirmation and lead-time statement for the quantity you need.
LM358APWRG4 vs LM358APU - which is better for a compact design?
The LM358APWRG4 is the better choice for a compact surface-mount design when an 8-pin TSSOP footprint is already designed in and the 0 to 70 C operating grade is acceptable. An alternative with a different package or temperature rating should only be selected after checking its footprint, pin numbering, channel assignments, and environmental requirements. Confirm the ordering table rather than assuming suffix equivalence.
How do I compare LM358APWRG4 with a cross-brand dual op amp?
Compare the cross-brand dual op amp against the LM358APWRG4 by package, channel pinout, supply range, input common-mode range, output swing, offset voltage, CMRR, slew rate, noise, output-current capability, and capacitive-load behavior. A cross-brand equivalent must also exist in an 8-pin TSSOP package. Equivalent functional performance alone does not establish a drop-in replacement.

داتای سەرچاوەی ئەندازیاری بۆ LM358APWRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM358APWRG4 for dual-channel, single-supply signal conditioning where 700 kHz bandwidth, 80 dB CMRR, and low supply current are more important than rail-to-rail operation. The same-family LM358 TSSOP alternatives can be considered for alternate sourcing, but the exact temperature grade, order suffix, and environmental documentation must match the design. Cross-brand LM358-type amplifiers in DIP-8 or SOIC-8 are not drop-in replacements for this TSSOP-8 PCB. If the signal must operate at or very near either supply rail, select a rail-to-rail amplifier instead. For high-impedance sources, also compare input bias current against the source impedance, and for capacitive loads verify stability using the manufacturer guidance.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM358APWR LM358APW LM358APT LM358APG4 LM358APWRG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package TSSOP-8 TSSOP-8 TSSOP-8 TSSOP-8 TSSOP-8 TSSOP-8
Amplifier Configuration Dual operational amplifier Dual operational amplifier Dual operational amplifier Dual operational amplifier Dual operational amplifier Dual operational amplifier
Gain-Bandwidth Product 700 kHz 700 kHz 700 kHz 700 kHz 700 kHz 700 kHz
Slew Rate 0.3 V/us 0.3 V/us 0.3 V/us 0.3 V/us 0.3 V/us 0.3 V/us
Input Offset Voltage 2 mV 2 mV 2 mV 2 mV 2 mV 2 mV
Common-Mode Rejection Ratio 80 dB 80 dB 80 dB 80 dB 80 dB 80 dB
Supply Current Drain 0.7 mA typical 0.7 mA typical 0.7 mA typical 0.7 mA typical 0.7 mA typical 0.7 mA typical
Typical Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Operating Temperature Range 0 C to 70 C Confirm order-code grade Confirm order-code grade Confirm order-code grade Confirm order-code grade 0 C to 70 C

جیاکەرەوە سەرەکییەکان

  • Two general-purpose amplifiers in one compact 8-pin TSSOP package (بەراورد بەLM358APWR)
  • Low supply-current drain for single-supply instrumentation (بەراورد بەLM358APW)
  • Common-mode rejection suited to noisy sensor environments (بەراورد بەLM358APT)

تێبینییەکانی دیزاین

Do not treat the 26 V maximum supply rating as an indication that the LM358APWRG4 can swing its output to either supply rail. The output stage is not rail-to-rail, so verify the output-voltage headroom for the highest expected signal and load. Likewise, confirm that every input remains within the usable common-mode range, including signals referenced to ground on a single 5 V supply.

Use the pin-description table in the manufacturer datasheet when assigning the two channels; TSSOP-8 and SOIC-8 LM358 variants can use different physical numbering conventions. Keep feedback resistors and compensation networks close to their amplifier pins, place the supply bypass capacitor at the device, and route each inverting input away from switching-node and high-current traces to reduce coupled noise.

Calculate the maximum stable frequency from the intended gain, source impedance, load, and any cable or sensor capacitance. The 700 kHz gain-bandwidth product and 0.3 V/us slew rate describe different limits: small-signal bandwidth can exceed the large-signal capability. Add isolation resistance or an output buffer if the load presents capacitance beyond the manufacturer-recommended operating conditions.

Both amplifiers share one TSSOP-8 package, so the dissipation from two simultaneously loaded channels must be evaluated together. Estimated: at a 5 V supply, a 3.5 V output and 2 mA load per channel, each channel dissipates approximately (5 V - 3.5 V) x 2 mA = 3 mW, or about 6 mW total. Actual self-heating depends on ambient temperature, copper area, and the package thermal resistance.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

A distributor product record identifies the LM358APWRG4 as RoHS-compliant, lead-free, and green. No separate REACH, halogen-free, conflict-minerals, or automotive-qualification statement is confirmed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM358APWRG4 datasheet LM358APWRG4 datasheet pdf LM358APWRG4 pinout LM358APWRG4 TSSOP-8 LM358APWRG4 specifications Texas Instruments LM358APWRG4 LM358APWRG4 equivalent LM358APWRG4 replacement LM358APWRG4 vs LM358APWR LM358APWRG4 drop-in substitute LM358APWRG4 price LM358APWRG4 stock LM358APWRG4 dual op amp 700 kHz LM358APWRG4 sensor signal conditioning LM358APWRG4 audio preamplifier

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM358APWRG4 LM358APWR LM358APW LM358APT LM358APG4 operational amplifier dual operational amplifier general-purpose amplifier analog signal conditioning voltage feedback amplifier common-mode rejection ratio CMRR gain-bandwidth product slew rate input offset voltage input bias current single-supply operation TSSOP-8 TSSOP package family surface mount SMD RoHS lead-free sensor interface audio preamplifier active filter current-to-voltage converter
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ