Texas Instruments

LM358PWR - Dual Op Amp, 700kHz, TSSOP-8 | Texas Instruments

MPN: LM358PWR ✓ چالاک
±1.5 V to ±16 V Vdss TSSOP-8 (PW) Package
MOQ: 1 |

LM358PWR گشتی

The Texas Instruments LM358PWR is an industry-standard dual operational amplifier integrating two general-purpose op-amp circuits in a single 8-pin TSSOP (PW) surface-mount package. Each amplifier offers a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operates from supply rails of ±1.5 V to ±16 V (or a single supply from 3 V to 32 V), making it one of the most widely deployed analog building blocks in electronics.

A dual operational amplifier is an analog integrated circuit that combines two independent, internally frequency-compensated, high-gain voltage amplifiers on one die. In the signal-chain hierarchy, an op amp is a foundational linear amplifier used to build gain stages, filters, comparators, integrators, current sinks, and voltage followers; the dual format halves board space and sharing one bias network improves thermal matching between channels.

Key features of the LM358PWR include common-mode input range extending to ground (a single-supply capability that many older op amps lack), high differential input voltage capability, and operation across both single and split supplies. The TSSOP-8 package measures roughly 6.4 mm x 4.4 mm with a 0.65 mm pitch, supporting compact surface-mount assemblies.

Architecturally, the LM358 uses an internally compensated bipolar design with a PNP differential input stage referenced to the negative rail, which is what allows inputs to operate down to 0 V in single-supply systems. The output stage sources and sinks current with a characteristic output swing that reaches near the negative rail.

Typical applications include transducer amplification, DC gain blocks, active filters, voltage comparators, LED drivers, and sensor signal conditioning in industrial controls, consumer appliances, and automotive body electronics (where the related LM2904 variant is common).

A key design consideration: the input offset voltage of the bipolar LM358 input stage (typically a few millivolts) limits precision; for sub-millivolt accuracy, consider the next-generation LM358B, which shares the same pinout with improved specifications.

This page consolidates verified specifications, pin-to-pin alternatives, application guidance, and design notes in one place - content that goes beyond what a raw datasheet listing provides.

جێگرەوەکانی جێگۆڕکێ بۆ LM358PWR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358PWR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Mounting Type, Slew Rate, Packaging.

Texas Instruments
Amplifier Type: General Purpose
Package: 8-TSSOP (PW), 0.173 in / 4.40 mm width
Packaging: Tape and Reel (TR)
بەراوردکردن لەگەڵ LM358PWR →
Texas Instruments
Amplifier Type: Dual general-purpose operational amplifier
Package: 8-pin TSSOP, 4.40 mm width
Packaging: Tape and reel
بەراوردکردن لەگەڵ LM358PWR →
Texas Instruments
Amplifier Type: General Purpose
Package: 8-TSSOP
Packaging: Tape and Reel (TR)
بەراوردکردن لەگەڵ LM358PWR →
Texas Instruments
Amplifier Type: JFET-Input Operational Amplifier
Mounting Type: Through Hole
Slew Rate: 13 V/µs (typical)
بەراوردکردن لەگەڵ LM358PWR →

LM358BPWR

✅ جێگرەوەی ڕاستەوخۆ
📦 TSSOP-8 (PW)
next-generation silicon: 36 V rating, 300 uV typical offset vs millivolt-class offset on LM358; pin-to-pin upgrade per TI product comparison

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904BPWR

✅ جێگرەوەی ڕاستەوخۆ
📦 TSSOP-8 (PW)
automotive/industrial grade variant of LM358B (36 V, 300 uV typ offset), same PW footprint and pinout

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904PWRG3

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 TSSOP-8 (PW)
General Purpose · 2 circuits · Two independent, frequency-compensated operational amplifiers · 26 V · 700 kHz · 0.3 V/us · 0.7 mA · Single supply or split supply

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358PWRG3

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 TSSOP-8 (TSSOP-B)
General Purpose · 2 circuits · 700 kHz · 16 V · 8-TSSOP · 4.40 mm · 0.173 inch · Tape and Reel (TR)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TL072CP

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 TSSOP-8
Texas Instruments · Active · JFET-Input Operational Amplifier · 2 (Dual) · 13 V/µs (typical) · 3 MHz (typical) · 30 pA (typical) · 3 mV (typical, C grade)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358PWR زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 2
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/us
Supply Voltage Range (Dual) ±1.5 V to ±16 V
Supply Voltage Range (Single) 3 V to 32 V
Common-Mode Input Range Extends to ground (single-supply capable)
Differential Input Voltage Capability High differential input voltage (per TI product page)
پاکێج TSSOP-8 (PW)
ژمارەی پین 8
جۆری دامەزراندن Surface Mount
Amplifier Type General Purpose / Standard
Next-Generation Upgrade LM358B (36 V, pin-to-pin upgrade with improved performance)

ڕێکخستنی پینی LM358PWR

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
پین 1 OUT A — Output of amplifier A
پین 2 IN A- — Inverting input of amplifier A
پین 3 IN A+ — Non-inverting input of amplifier A
پین 4 V- — Negative supply / ground in single-supply operation
پین 5 IN B+ — Non-inverting input of amplifier B
پین 6 IN B- — Inverting input of amplifier B
پین 7 OUT B — Output of amplifier B
پین 8 V+ — Positive supply

بەکارهێنانە باوەکان

LM358PWR گونجاوە بۆ 6 بەکارھێنانs: Sensor Signal Conditioning, Active Filter Design, Voltage Comparison and Level Detection, LED Driver and Current Sink Circuits, Audio Preamplifier and Mixer Stages, Industrial Control and Appliance Electronics.

🧩

Sensor Signal Conditioning

The LM358PWR fits transducer front ends because its common-mode input range extends to ground, letting ground-referenced sensor outputs be amplified on a single supply without a negative rail. With a 700 kHz gain-bandwidth product, a gain of 10 (20 dB) still sustains roughly 70 kHz of bandwidth, far above the response time of temperature, pressure, and light sensors. Each of the two channels can buffer and amplify a separate sensor, or one channel can provide gain while the other builds a reference or comparator stage. In a typical single-supply 5 V or 12 V system, the output swings toward the negative rail, maximizing usable dynamic range for small signals. The trade-off is the bipolar input stage's millivolt-class offset, so for sub-millivolt bridges the LM358BPWR upgrade with 300 uV typical offset should be evaluated.

🔧

Active Filter Design

Multiple-feedback and Sallen-Key low-pass or band-pass filters commonly use the LM358PWR because two amplifiers per package implement a complete second-order section with one device. At a 700 kHz gain-bandwidth product, unity-gain Sallen-Key stages remain accurate well into the tens of kilohertz: for example, a 20 kHz cutoff filter sees only minimal Q degradation. In single-supply circuits the input range to ground allows mid-supply biasing with simple resistor dividers, and the output stage drives RC filter networks directly. Designers should keep closed-loop gain-bandwidth usage below roughly one-tenth of 700 kHz per stage to preserve filter response accuracy. Where faster filters or lower noise are needed, the JFET-input TL072 in the same dual footprint is the classic substitute.

⚙️

Voltage Comparison and Level Detection

The LM358PWR doubles as an economical comparator for slow over-voltage, under-voltage, and threshold detection tasks documented in the TI datasheet's application section. One channel monitors a divided-down supply rail while the second remains available for reference buffering, giving two-level supervision in a single 8-pin TSSOP. Because the common-mode input includes ground, signals referenced to 0 V can be sensed directly in single-supply systems. The practical limitation is large-signal speed: at 0.3 V/us slew rate, a full-rail transition takes tens of microseconds, which is acceptable for supervisory and alarm circuits but unsuitable for fast pulse discrimination. Adding positive feedback resistors creates hysteresis to prevent chatter near the threshold, a technique shown in the manufacturer's typical application circuits.

💡

LED Driver and Current Sink Circuits

Constant-current LED drivers built around the LM358PWR exploit its ground-sensing input: the amplifier servos the voltage across a current-sense resistor to a reference, so LED current equals Vref/Rsense. With single-supply operation from 3 V to 32 V, one LM358PWR channel can regulate LED strings in indicator, backlight, and small lighting applications directly from an unregulated DC rail. The output stage sources enough current through a pass transistor to control hundreds of milliamps with proper device selection. The 700 kHz bandwidth closes the control loop fast enough to reject ripple and supply transients, keeping LED brightness stable. Thermal design centers on the external pass transistor, since the TSSOP-8 amplifier itself dissipates little power in this topology.

🎧

Audio Preamplifier and Mixer Stages

The LM358PWR serves cost-sensitive audio preamplification, mixing, and summing amplifier stages where 700 kHz of bandwidth comfortably exceeds the 20 kHz audio band even at moderate gains - a gain of 20 (26 dB) still delivers about 35 kHz of closed-loop bandwidth. Two channels per TSSOP-8 package process stereo signals with matched thermal behavior, and single-supply operation with input range to ground simplifies biasing in portable or USB-powered designs. Designers should note the bipolar input noise and crossover behavior of the classic LM358 output stage are audible in high-fidelity contexts; the next-generation LM358BPWR improves performance on the same footprint. For low-noise applications, JFET or low-noise alternatives in the same dual pinout can be dropped in without PCB changes.

🏭

Industrial Control and Appliance Electronics

In industrial controllers, appliances, and body electronics, the LM358PWR provides buffering, gain, and comparison functions across the wide ±1.5 V to ±16 V supply range, tolerating both regulated 5 V logic rails and higher 12 V to 24 V industrial supplies. The wide operating range and the availability of the automotive-related LM2904 family on the same footprint make board designs portable between consumer and industrial-grade builds. Typical uses include current-loop interfaces, photoelectric sensor amplifiers, motor current monitors, and boiler/appliance control signal chains. Two amplifiers per package reduce BOM line items, and the industry-standard pinout means second sources - including Rohm's LM358PWR - exist for supply-chain resilience. Verify temperature grade requirements against the datasheet for installations outside room-ambient conditions.

کورتەی بەرهەمە پێشنیارکراوەکان

TS321IDR Texas Instruments بەکارهێنراوە لە: Sensor Signal Conditioning, Voltage Comparison and Level Detection, LED Driver and Current Sink Circuits LM358BPWR Low-offset drop-in upgrade for precision sensor front ends بەکارهێنراوە لە: Sensor Signal Conditioning, Voltage Comparison and Level Detection TL072 JFET-input dual op amp alternative for higher-frequency filters بەکارهێنراوە لە: Active Filter Design TS922AID STMicroelectronics بەکارهێنراوە لە: Active Filter Design, Audio Preamplifier and Mixer Stages TS924IPT STMicroelectronics بەکارهێنراوە لە: LED Driver and Current Sink Circuits TS932IDT STMicroelectronics بەکارهێنراوە لە: Audio Preamplifier and Mixer Stages LM2904PWR Texas Instruments بەکارهێنراوە لە: Industrial Control and Appliance Electronics LM2904BPWR Improved 36 V industrial-grade drop-in upgrade بەکارهێنراوە لە: Industrial Control and Appliance Electronics
What is the gain bandwidth product of the LM358PWR?
The LM358PWR has a gain-bandwidth product of 700 kHz. According to the TI LM358PWR specifications, each of the two internal op-amp circuits delivers 700 kHz of bandwidth with a 0.3 V/us slew rate, which is sufficient for audio-frequency gain stages, slow sensor conditioning, and active filters below roughly 50 kHz of closed-loop bandwidth.
What supply voltage range does the LM358PWR support?
The LM358PWR operates from ±1.5 V to ±16 V on dual supplies, or equivalently 3 V to 32 V on a single supply. This wide range makes it usable in 5 V single-supply microcontroller systems as well as traditional ±15 V analog backplanes. A single-supply design benefit is that the common-mode input range extends down to ground, so signals referenced to 0 V can be amplified without a negative rail.
What package is the LM358PWR and what is its pinout?
The LM358PWR comes in an 8-pin TSSOP (PW) package. The industry-standard dual op-amp pinout is: pin 1 OUT A, pin 2 IN A- (inverting), pin 3 IN A+ (non-inverting), pin 4 V- (ground/negative supply), pin 5 IN B+, pin 6 IN B-, pin 7 OUT B, pin 8 V+ (positive supply). This pinout is shared by the entire LM358, LM2904, and most dual op-amp families, enabling pin-to-pin substitution.
Where can I download the LM358PWR datasheet PDF?
The LM358PWR datasheet PDF is available on the Texas Instruments product page at ti.com under the LM358 family, which covers the PW (TSSOP-8) suffix used by the LM358PWR. The datasheet document describes the dual operational amplifier electrical characteristics, typical application circuits, and package dimensions. Request a quote on this page for the current price, stock, and lead time.
What is the difference between LM358PWR and LM358BPWR?
The LM358B is the next-generation silicon revision of the industry-standard LM358, and the LM358BPWR is the same TSSOP-8 (PW) package with the same pinout. According to TI, the LM358B devices are high-voltage (36 V) op amps with improved specifications, including low offset (300 uV typical) versus the older process. TI's own product comparison describes it as a pin-to-pin upgrade with improved performance, so it can directly replace an LM358PWR on the same PCB footprint.
Can the LM358PWR be replaced by LM2904?
Yes, the LM2904 is a pin-to-pin compatible dual op amp in the same family and can be used as a drop-in replacement for the LM358PWR in the same TSSOP-8 package. The LM2904 is the automotive/industrial-grade variant of the same design and shares the 700 kHz class performance. TI's next-generation LM2904B additionally offers 36 V ratings and 300 uV typical offset, providing an improved drop-in path for both industrial and automotive designs.
Is the LM358PWR suitable for single-supply 5V operation?
Yes. The LM358PWR operates from a single 3 V to 32 V supply, so 5 V operation is fully within range. Its common-mode input range extends to ground, which is the defining single-supply feature of the LM358 family: input signals at or near 0 V can be handled, and the output can swing close to the negative rail. Note the output cannot reach the positive rail, so allow headroom near V+ when planning output swing in a 5 V system.
What is the best LM358PWR equivalent from another manufacturer?
Rohm Semiconductor manufactures an LM358PWR in an 8-pin TSSOP-B package that is a direct cross-brand equivalent: same dual general-purpose amplifier function, same industry-standard pinout, and same footprint class. Pin-compatible dual op amps such as the RC4558 share the same footprint but differ in performance class, and the TL072 offers JFET inputs with higher speed but different input common-mode behavior, so verify parameters against your circuit before substituting.
When should I choose the LM358PWR over a precision op amp?
Choose the LM358PWR when your design needs a cost-effective, widely available dual general-purpose amplifier for gain stages above a few tens of millivolts of signal, filtering, or comparison functions, and when 700 kHz bandwidth and a 0.3 V/us slew rate are sufficient. Choose a precision, low-offset op amp instead when input offset in the millivolt class would cause unacceptable DC error, such as in high-gain thermocouple or bridge-sensor front ends.
Can I use the LM358PWR as a comparator?
Yes, the LM358 is commonly used as a comparator and the TI datasheet documents comparator-style application circuits. However, an op amp used as a comparator is not specified for response time or hysteresis behavior the way a dedicated comparator is: with a 0.3 V/us slew rate, large-signal switching is slow, and open-loop operation can be sluggish. For fast over-voltage detection, use a dedicated comparator; for slow level detection, the LM358PWR is an economical choice.
What are the key specifications of the LM358PWR that engineers should know?
The LM358PWR is a Texas Instruments dual general-purpose operational amplifier in an 8-pin TSSOP (PW) package with 700 kHz gain-bandwidth, 0.3 V/us slew rate, and a supply range of ±1.5 V to ±16 V (3 V to 32 V single supply). Its single-supply capability with common-mode input range to ground, two matched amplifiers in one package, and industry-standard pinout are the headline features that explain its ubiquity in cost-sensitive analog designs.
Where to buy LM358PWR online and how much does it cost?
The LM358PWR can be purchased directly through XAIPART using the Request a Quote form on this page, which returns current unit pricing at your required quantity, stock availability, and lead time. The device is an active, high-volume industry-standard part, so multi-source availability is generally excellent. For volume pricing breaks and reel quantities, indicate your annual usage in the quote request.
What is the lead time and packaging of the LM358PWR?
The LM358PWR ships in tape-and-reel format for surface-mount assembly; request the exact standard reel quantity and current lead time through the Request a Quote form on this page. As an active Texas Instruments part in continuous production since it became an industry standard, the LM358PWR is typically a short-lead-time commodity, but lead times vary with market demand and should be confirmed at order time.
Is the LM358PWR the same as the LM358N?
The LM358PWR and LM358N are the same die and function but differ in package: the PWR suffix denotes an 8-pin TSSOP (PW) surface-mount package, while the N suffix denotes an 8-pin PDIP through-hole package. Electrically both provide two 700 kHz class op amps with the identical pinout (1-OUT A, 2-IN A-, 3-IN A+, 4-V-, 5-IN B+, 6-IN B-, 7-OUT B, 8-V+). They are interchangeable electrically, not mechanically - match the suffix to your PCB footprint.
Does the LM358PWR meet RoHS compliance requirements?
RoHS compliance for the LM358PWR is confirmed on the official TI product page; consult the TI product detail page for the current RoHS and REACH status of the PWR (TSSOP-8) suffix. As a currently active, high-volume TI part intended for global markets, the PW package is produced in lead-free surface-mount technology. Request a quote on this page for the part, and confirm the compliance certificate through the manufacturer's environmental documentation.

داتای سەرچاوەی ئەندازیاری بۆ LM358PWR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM358PWR when you need a proven, low-cost dual general-purpose op amp for gains, filters, slow comparisons, or LED/current loops on a 3 V to 32 V single supply or ±1.5 V to ±16 V dual supply, and when millivolt-class input offset is acceptable. Choose the LM358BPWR when you want the same TSSOP-8 footprint with 36 V tolerance and 300 uV typical offset - TI markets it as a pin-to-pin upgrade. Choose the LM2904PWR or LM2904BPWR when automotive or industrial qualification grade matters; they are pin-compatible on the same land pattern. Choose the Rohm LM358PWR for identical function from a second manufacturer. Avoid the classic LM358PWR for precision DC front ends, high-speed paths beyond a few hundred kHz, or rail-to-rail output requirements - select a precision or rail-to-rail dual op amp instead.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM358BPWR LM2904BPWR LM2904PWR LM358PWR (Rohm)
Package TSSOP-8 (PW) TSSOP-8 (PW) - same TSSOP-8 (PW) - same TSSOP-8 (PW) - same TSSOP-8 (TSSOP-B) - same footprint class
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Rohm Semiconductor
Number of Amplifiers 2 2 2 2 2
Gain-Bandwidth Product 700 kHz 700 kHz 700 kHz 700 kHz 700 kHz
Grade / Target Market Standard commercial/industrial Next-generation standard Automotive/industrial grade Automotive/industrial grade Standard general purpose
Pin-to-Pin Compatibility Industry-standard dual op-amp pinout Pin-to-pin upgrade (per TI) Pin-compatible Pin-compatible Pin-compatible (industry standard)

جیاکەرەوە سەرەکییەکان

  • Industry-standard ubiquity and second sourcing (بەراورد بەLM358PWR (Rohm Semiconductor))
  • Single-supply input range to ground (بەراورد بەTL072)
  • Immediate low-offset upgrade path (بەراورد بەLM358BPWR)

تێبینییەکانی دیزاین

Do not expect output swing to the positive rail: the classic LM358 output stage saturates well below V+, typically losing over a volt of headroom. Plan gain and signal levels so the output peak stays below the datasheet output swing limits, or use a rail-to-rail output alternative such as the TS924/TS932 family in headroom-critical single-supply designs. Also remember the input common-mode range includes ground but a high-side input near V+ will saturate the input stage. Ignoring these two limits is the most common cause of clipping and nonlinear behavior in single-supply LM358 designs.

Decouple V+ (pin 8) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus bulk capacitance (1 uF to 10 uF) at the board level. In split-supply configurations, decouple the V- rail as well. Long supply traces on two-layer boards can couple digital switching noise into the 700 kHz bandwidth amplifiers, appearing as buzz in audio circuits. The device's wide supply range of ±1.5 V to ±16 V tolerates unregulated rails, but verify that transient surges in industrial environments stay within the absolute maximum ratings.

The bipolar PNP input stage draws bias current through the external network; keep the resistance seen by both inputs of each amplifier matched so bias-current errors cancel rather than become offset. In high-gain stages (greater than 100), the millivolt-class input offset of the classic LM358 becomes the dominant DC error - use the LM358BPWR (300 uV typical offset, same footprint) for such designs. Use a ground-plane or short return paths for input networks to limit hum and noise pickup at the high-impedance summing junctions.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status should be confirmed on the official TI product page for the LM358PWR suffix; the LM2904/LM2904B family covers the automotive-grade variants of this design.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM358PWR datasheet LM358PWR datasheet pdf LM358PWR pinout LM358PWR equivalent LM358PWR replacement LM358PWR cross reference LM358PWR vs LM358B Texas Instruments LM358PWR LM358 TSSOP-8 dual op amp LM358 single supply op amp 5V LM358 vs TL072 dual op amp LM358PWR price

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM358PWR LM358 LM358B LM2904 LM2904B TL072 Rohm Semiconductor operational amplifier dual op amp general purpose amplifier linear amplifier gain-bandwidth product slew rate single-supply operation common-mode input range TSSOP-8 surface mount PW package RoHS pin-to-pin replacement active filter sensor signal conditioning audio preamplifier
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ