onsemi

LM358SNG - Dual Op-Amp, 3-32V, 8-PDIP | onsemi

MPN: LM358SNG ✓ چالاک
3 V to 32 V Vdss 45 nA Id 8-PDIP (0.300 in, 7.62 mm) Package
MOQ: 1 |

LM358SNG گشتی

The onsemi LM358SNG is a single-supply dual operational amplifier with two independent general-purpose amplifier circuits in an 8-pin PDIP (0.300 in, 7.62 mm) package. It operates from a 3V to 32V single supply (or ±1.5V to ±16V dual supplies) and features a low input bias current of 45 nA, making it a classic value-line bipolar op-amp for cost-sensitive analog designs.

A general-purpose operational amplifier is an analog building block that amplifies the voltage difference between its two inputs with high open-loop gain and is configured for gain, filtering, buffering, or comparison through external passive components. Op-amps sit at the core of the analog signal chain hierarchy: op-amp -> amplifier IC -> linear/analog IC -> semiconductor, and the LM358 family was the first industry-standard dual op-amp optimized for single-supply operation.

Key features include dual matched amplifiers sharing one bias network for low offset drift, an input common-mode range that includes ground (true single-supply capability), and wide supply operation from 3V to 32V. The two circuits are internally matched, which reduces quiescent power per amplifier and simplifies dual-channel designs on a single rail.

Technically, the LM358SNG uses bipolar process technology with internal frequency compensation, so it is unity-gain stable without external capacitors. The output stage can source and sink current to ground on a single rail, though output swing is limited to within roughly one diode drop of the negative rail. This makes it well suited to low-frequency analog front ends rather than high-speed signal processing.

Typical applications include transducer signal conditioning, DC gain blocks and active filters, voltage comparators and level detection, current sensing on single-supply microcontroller boards, and audio preamp stages in battery-powered equipment where a single positive rail must be used.

When designing with this device, reserve gain-bandwidth-limited topologies to audio-range frequencies and always provide a supply decoupling capacitor close to pin 8. For precision designs, verify input offset voltage over temperature because value-line bipolar input stages drift more than modern precision CMOS parts.

This page synthesizes distributor availability, drop-in alternatives, package pinout, and practical design notes in one place, going beyond a plain datasheet listing.

جێگرەوەکانی جێگۆڕکێ بۆ LM358SNG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358SNG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Supply Configuration, Mounting Type, Product Type, Amplifier Type.

Texas Instruments
Package: 8-pin PDIP
Supply Configuration: Single supply or split supply
Mounting Type: Through-hole
بەراوردکردن لەگەڵ LM358SNG →
Texas Instruments
Package: 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source
Supply Configuration: Single supply operation emphasized in the verified LM358 family description
Mounting Type: Through-hole
بەراوردکردن لەگەڵ LM358SNG →
onsemi
Supply Configuration: Single supply or split supply operation
Mounting Type: Through-hole
Product Type: Dual general-purpose operational amplifier
بەراوردکردن لەگەڵ LM358SNG →
Diodes Incorporated
Package: 8-SO
Supply Configuration: Single supply
Mounting Type: Surface mount
بەراوردکردن لەگەڵ LM358SNG →

LM2904NG

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
onsemi
📦 8-PDIP (7.62 mm)
General Purpose · 2 · 1 MHz · 0.6 V/µs · 3 V to 26 V · -40C to +105C · PDIP-8 (0.300 in, 7.62 mm) · Through Hole

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358NG

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
onsemi
📦 8-PDIP (7.62 mm)
Dual general-purpose operational amplifier · 2 channels · 3 V to 32 V · 1 MHz · 0.6 V/µs · 7 mV · 100 nA · Extends to ground/VEE

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM358N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-PDIP (7.62 mm)
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-PDIP (7.62 mm)
2 amplifiers · 26 V · 1 MHz · Dual independent operational amplifiers · Internally frequency compensated · Single supply or split supply · Extending to ground/VEE

پەیوەندی بۆ نرخ

بینینی داتاشیت →

RC4558N

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP (7.62 mm)
audio-oriented dual op-amp, same DIP-8 pinout, different noise/bandwidth profile and no ground-sensing input range

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TL072CN

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP (7.62 mm)
JFET-input dual op-amp, same DIP-8 pinout, picoamp bias current and higher slew rate but weaker single-supply ground sensing

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM358SNG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type General Purpose Operational Amplifier
Number of Circuits 2
پاکێج 8-PDIP (0.300 in, 7.62 mm)
Supply Voltage (Single) 3 V to 32 V
Supply Voltage (Dual) ±1.5 V to ±16 V
Input Bias Current 45 nA
Amplifier Class Class AB (value line)
جۆری دامەزراندن Through Hole
Packaging Tube (50 per tube)
Product Type Family Single Supply Dual Operational Amplifiers

ڕێکخستنی پینی LM358SNG

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 V- / GND — Negative supply or ground (single supply)
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 V+ — Positive supply, 3 V to 32 V

بەکارهێنانە باوەکان

LM358SNG گونجاوە بۆ 6 بەکارھێنانs: Transducer Signal Conditioning, DC Gain Blocks and Active Filters, Voltage Comparison and Level Detection, Current Sensing on Single-Supply Boards, Battery-Powered Portable Instruments, Legacy Equipment Repair and Retrofit.

🔧

Transducer Signal Conditioning

Sensor front ends such as thermistors, photodiodes with load resistors, and pressure bridges frequently produce millivolt-level, ground-referenced signals on boards that carry only a single positive rail. The LM358SNG fits this role because its input common-mode range extends to ground and it operates down to 3V, so 5V or even 3.3V-derived rails can power it directly. A typical topology is a non-inverting amplifier with gain set by two resistors, giving 10x to 100x amplification of a ground-near sensor voltage into the ADC range of a microcontroller. Because the value-line bipolar input carries 45 nA bias current, keep source impedances below roughly 100 kilo-ohms to limit offset errors, and decouple the 3V to 32V supply pin with a 100 nF capacitor placed close to pin 8.

🎧

DC Gain Blocks and Active Filters

The two matched amplifier circuits inside the LM358SNG make it efficient for second-order active filters and multi-stage DC gain blocks, since both stages share one 8-pin PDIP footprint and one bias network. With internal compensation the device is unity-gain stable, so Sallen-Key and multiple-feedback topologies can be built without external frequency-compensation parts. The practical limit is bandwidth: this value-line bipolar part is intended for audio-range and low-frequency filtering, so cutoff frequencies in the tens of kilohertz are comfortable while megahertz filters require a faster amplifier. On a 24V industrial rail the device tolerates the full 3V to 32V single-supply range per the datasheet, allowing high-headroom filter outputs, but keep the output swing expectations about a diode drop away from each rail.

⚡

Voltage Comparison and Level Detection

Using one amplifier of the LM358SNG as a comparator is a classic low-cost technique for window detectors, over-voltage flags, and battery-low monitors on single-supply boards. The open-collector-free push-pull output of the bipolar stage drives logic inputs directly, and the ground-including input common-mode range lets one input sit at a ground-referenced divider while the other references a zener or regulator threshold. Because the device is not specified as a dedicated comparator, switching speed is modest and switching near the rail can be slow, so for fast edge detection use hysteresis of tens of millivolts via positive feedback or move to a true comparator. The second amplifier in the same PDIP-8 package is then free for the reference buffer or a pre-scaling gain stage.

⚡

Current Sensing on Single-Supply Boards

Low-side current sensing pairs a small shunt resistor near ground with an amplifier that translates the shunt voltage into a microcontroller-readable signal, and the LM358SNG is well matched because its inputs read accurately at ground potential. With a 0.1 ohm shunt and a non-inverting gain of 50, a 1 A load produces a 5 V output on a 12V or 24V rail within the 3V to 32V supply rating. The 45 nA input bias current creates negligible shunt error, but the output cannot reach the rail exactly - reserve roughly one diode drop of headroom when defining full-scale. Add a small RC filter between shunt and input to reject PWM noise, and use a 100 nF decoupling capacitor at pin 8 to keep switching ripple out of the measurement.

📱

Battery-Powered Portable Instruments

Portable meters, data loggers, and test probes run from single cells or small battery packs, and the LM358SNG accepts supplies down to 3V, matching two alkaline cells or a single lithium cell with a regulator. Each amplifier draws modest quiescent current appropriate for value-line battery designs, and the dual channels let one package handle both signal amplification and reference buffering, halving the IC count versus two single op-amps. The through-hole PDIP-8 package also suits hand-repairable field instruments and educational kits. For maximum battery life, avoid resistive dividers below 100 kilo-ohms on the inputs so that bias-current loading stays negligible, and keep gains modest since open-loop headroom near the rails is limited on this bipolar output stage.

🖥️

Legacy Equipment Repair and Retrofit

Industrial controllers, test fixtures, and audio gear from the 1980s onward used LM358-family dual op-amps in socketed DIP-8 footprints, and the LM358SNG is the natural service replacement because it preserves the exact package, pinout, and bias behavior of the original onsemi part. Distributor cross-reference catalogs list the LM358 family across manufacturers as pin-to-pin interchangeable, which means a failed generic LM358 in a socket can be replaced by this part without board modification. When retrofitting, inspect the surrounding circuit for rail-to-rail output assumptions - older designs expected the classic diode-drop output swing limit, so direct substitution preserves correct behavior whereas replacing with a modern rail-to-rail op-amp can actually change comparator thresholds and calibration points in legacy boards.

What is the LM358SNG?
The LM358SNG is onsemi's single-supply dual operational amplifier in an 8-pin PDIP through-hole package. It contains two independent, internally compensated general-purpose amplifier circuits that operate from a 3V to 32V single supply, or from dual supplies of ±1.5V to ±16V. According to the onsemi datasheet, the input bias current is 45 nA, and the two amplifiers share matched biasing for consistent performance across both channels.
What is the supply voltage range of the LM358SNG?
The LM358SNG operates from a single supply of 3V to 32V, or from split supplies of ±1.5V to ±16V, according to the onsemi product listing. This wide range lets one device serve 5V microcontroller boards, 12V and 24V industrial rails, and traditional dual-rail analog systems, as long as the total supply voltage across the part stays within 32V.
Why is the LM358 good for single supply operation?
The LM358 family was the first industry-standard dual op-amp designed specifically for single-supply use. Its input common-mode voltage range includes the negative (ground) rail, and its output stage can drive close to ground on a single positive rail. This lets the LM358SNG amplify ground-referenced sensor signals without a negative supply, which simplifies battery-powered and microcontroller-based designs where only a positive rail exists.
What is the difference between LM358SNG and LM358N?
Both are dual general-purpose op-amps in the same 8-pin PDIP package with identical pinouts, so they are drop-in interchangeable. The LM358SNG is onsemi's catalog number for the through-hole DIP version, while LM358N is the naming used by Texas Instruments and other manufacturers for the same industry-standard circuit. According to distributor cross-reference listings, LM358N is listed as a pin-to-pin replacement for LM358 parts; always verify temperature range and offset specifications on the specific manufacturer datasheet before production.
What is the best drop-in replacement for LM358SNG?
The closest drop-in replacements are other LM358-family parts in 8-pin PDIP: onsemi LM2904N (same pinout, automotive/industrial temperature grade) and TI LM358N (same circuit, same footprint). Distributor cross-reference tools including the DigiKey cross-reference search list LM358N and LM2904 as pin-compatible substitutes. For slightly better performance, the TL072 offers the same DIP-8 pinout but uses JFET inputs, so input bias current drops to the picoamp range while behavior at rail-to-rail conditions differs.
Can TL072 replace LM358SNG?
Yes, the TL072 is pin-compatible in the 8-pin DIP package and can physically replace the LM358SNG, but it is not a perfect electrical equivalent. The TL072 uses JFET inputs with much lower bias current and higher slew rate, which improves AC performance, but its input common-mode range does not reach the negative rail as gracefully and it is not specified for the same single-supply ground-referenced operation. For circuits that sense ground-level signals on a single rail, prefer an LM358-family replacement; for AC-coupled audio paths, the TL072 often performs better.
When should I choose LM358SNG over LM2904N?
Choose the LM358SNG when your design stays within the commercial/industrial temperature environment and you want the standard commercial-grade part at the lowest cost. Choose the LM2904N when the product must survive automotive or extended industrial temperatures, since the LM2904 family is qualified for wider temperature ranges. Both share the same 8-pin PDIP pinout, so switching between them does not require PCB changes - only the temperature and drift specifications in the datasheets differ.
Is LM358SNG suitable for audio applications?
The LM358SNG can be used for basic audio preamp and mixer stages, and it is unity-gain stable with internal compensation, so no external capacitor is needed. However, it is a value-line bipolar part with limited slew rate and bandwidth, so for demanding hi-fi circuits or high-gain wideband stages, a faster part such as the TL072 or an audio-specialized op-amp gives lower distortion. For battery-powered, single-rail audio products, the LM358SNG remains a proven, low-cost choice.
What package does the LM358SNG come in?
The LM358SNG comes in an 8-pin plastic dual in-line package (PDIP) with 0.300 inch (7.62 mm) row spacing, intended for through-hole mounting on 2.54 mm grid boards. It ships in tubes of 50 units per the distributor listing. The PDIP package makes it popular for prototyping, educational kits, breadboard designs, and repair of legacy equipment where socketed ICs are standard.
What are the key specifications of the LM358SNG engineers should know?
The key facts are: two internally compensated op-amps in one 8-pin PDIP, 3V to 32V single-supply operation (±1.5V to ±16V dual), 45 nA input bias current per the onsemi datasheet, and input common-mode range that includes ground. These parameters define its role: a low-cost, ground-sensing, dual-channel amplifier for low-frequency signal conditioning, filtering, and comparison on single positive rails up to 32V.
Where can I download the LM358SNG datasheet PDF?
The onsemi LM358SNG datasheet PDF is available through the datasheet link on this page and from the onsemi official website product page. The document, titled Single Supply Dual Operational Amplifiers, contains the complete pin description, electrical characteristic tables over temperature, typical application circuits, and package dimensional drawings for the 8-PDIP package. Always use the latest revision from the manufacturer for design work.
What is the pinout of the LM358SNG in PDIP-8?
The LM358SNG follows the standard dual op-amp DIP-8 pinout: pin 1 is amplifier 1 output, pin 2 is amplifier 1 inverting input, pin 3 is amplifier 1 non-inverting input, pin 4 is ground or negative supply (V-), pin 5 is amplifier 2 non-inverting input, pin 6 is amplifier 2 inverting input, pin 7 is amplifier 2 output, and pin 8 is the positive supply (V+). This pinout is shared across the entire LM358 family, enabling direct substitution.
Where to buy LM358SNG and what is its price?
The LM358SNG is stocked by major electronics distributors, and current pricing and availability for this page are handled through the Request a Quote form - enter your quantity and you will receive a response with price, stock, and lead time. Distribution listings for this part exist on multiple channels, and as a value-line general-purpose amplifier it is a low-cost, widely available catalog part rather than a constrained or allocation item.
What is the lead time and MOQ for LM358SNG?
The LM358SNG is an active, mass-produced general-purpose amplifier, so it is generally a short-lead-time catalog item stocked in tube packaging of 50 pieces. Exact lead time depends on order quantity and current channel inventory. Submit your required quantity and delivery date through the Request a Quote form on this page and the response will confirm current stock, minimum order quantity, and shipping schedule for your region.
Is the LM358SNG RoHS compliant and lead-free?
Current production onsemi PDIP components such as the LM358SNG are supplied in RoHS-compliant, lead-free finishes; the manufacturer product page and distributor listings are the authoritative source for the exact compliance declarations for the specific date code you purchase. Because PDIP leads on legacy families historically used tin-lead plating on older stock, verify the compliance statement on the onsemi product page or request the material declaration sheet before qualifying the part for a new RoHS-controlled product.

داتای سەرچاوەی ئەندازیاری بۆ LM358SNG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM358SNG when you need a proven, low-cost dual op-amp for ground-referenced signals on a single 3V to 32V rail, in a through-hole PDIP-8 footprint that suits prototyping, education, and legacy repair. Choose the onsemi LM2904NG or TI LM2904N when the product must operate over extended or automotive temperature ranges - both are pin-identical drop-ins. Choose TI LM358N when supply-chain diversification across manufacturers matters; distributor cross-reference tools list it as a pin-to-pin substitute. Choose the TL072CN only for AC-coupled or high-impedance circuits where its JFET picoamp bias current and higher speed help, accepting its weaker single-supply ground behavior. Avoid this whole value-line family for precision offset-critical or megahertz-bandwidth designs - a modern precision CMOS or high-speed amplifier is the right tool there.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2904NG LM358N LM2904N TL072CN
Package 8-PDIP (7.62 mm) 8-PDIP (7.62 mm) - same 8-PDIP (7.62 mm) - same 8-PDIP (7.62 mm) - same 8-PDIP (7.62 mm) - same
Brand onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Number of Circuits 2 2 2 2 2
Input Bias Current 45 nA similar bipolar level (datasheet value) 45 nA typical class similar bipolar level (datasheet value) picoamp-range (JFET input)
Input Technology Bipolar Bipolar Bipolar Bipolar JFET
Single-Supply Ground Sensing Yes (input includes ground) Yes Yes Yes Limited (JFET common-mode range)

جیاکەرەوە سەرەکییەکان

  • True single-supply ground sensing (بەراورد بەTL072CN)
  • Ultra-low JFET-class bias current alternative exists at same footprint (بەراورد بەTL072CN)
  • Extended-temperature sibling available without PCB change (بەراورد بەLM2904NG)

تێبینییەکانی دیزاین

Decouple pin 8 (V+) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a bulk 10 uF electrolytic on the board supply. On single-supply rails above 24V, remember the absolute total supply limit of 32V per the datasheet - automotive 12V systems with load dump need protection upstream. Estimated: at a typical 0.5 mA per-amplifier quiescent level, self-heating in the PDIP-8 is well under thermal limits for any rail within the rated 32V range.

The output stage does not swing to the rails: on a single supply, expect the output to sit roughly one diode drop above ground at the low end. Designs that assume output reaches 0V (for example driving a comparator threshold or ADC zero-scale) will show a residual offset. Also keep input source impedances moderate - with 45 nA bias current, a 1 mega-ohm source adds tens of millivolts of apparent offset. For ground-near sensing with high impedance sources, add a buffer stage or select a CMOS-input op-amp.

The LM358 is unity-gain stable but bandwidth-limited; estimated from value-line bipolar family behavior, closed-loop bandwidth above roughly 100 kHz at gains of 10 or more is not realistic, so do not use it for fast comparators or megahertz filtering without verifying transient response on the bench. When using one amplifier as a comparator, add 10-50 mV of hysteresis via positive feedback to prevent output chatter from slow edges crossing the threshold, and keep amplifier 2's feedback components physically separated from amplifier 1's summing node on the PCB.

The PDIP-8 through-hole footprint (7.62 mm row spacing, 2.54 mm pitch) fits standard sockets, which simplifies rework in prototype and service contexts. Keep the input traces (pins 2, 3, 5, 6) short and guard them with ground when high-impedance nodes are used, because leakage across the board can exceed the 45 nA bias current itself. Route the amplifier 1 output away from amplifier 2 inputs to prevent crosstalk in high-gain two-stage chains.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance declarations were not stated in the retrieved product listings; confirm on the onsemi official product page or request a material declaration for the specific date code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm358 single supply lm358s datasheet LM358SNG datasheet LM358SNG datasheet pdf LM358SNG pinout LM358SNG equivalent LM358SNG replacement LM358SNG cross reference LM358SNG vs LM358N LM358SNG price LM358SNG stock onsemi LM358SNG LM358 PDIP-8 pinout LM358 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

onsemi LM358SNG LM358 LM2904NG LM358N TL072CN operational amplifier op-amp dual op-amp amplifier IC analog IC PDIP-8 DIP (0.300 inch, 7.62 mm) through-hole mounting single-supply operation input bias current RoHS transducer signal conditioning active filter voltage comparator
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ