Texas Instruments

LM393AP - Dual 36V Open-Collector Comparator | Texas Instruments

MPN: LM393AP ✓ چالاک
2 V to 36 V Vdss 0.4 mA drain current Id 8-pin PDIP Package
MOQ: 1 |

LM393AP گشتی

The Texas Instruments LM393AP is a dual differential comparator with two independent comparator channels, a 2 V to 36 V single-supply operating range, and a 300 ns response time in an 8-pin PDIP package. Each channel provides an open-collector output that can sink useful load current and operate at voltages up to 36 V. The device is intended for general-purpose commercial applications requiring threshold detection, signal conditioning, or simple analog decision-making.

A differential comparator is an analog IC that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM393AP belongs to the comparator hierarchy, where a comparator is a specialized amplifier IC used for voltage-level detection rather than linear signal amplification. Its two independent channels allow one package to implement two separate sensing or control functions.

Key characteristics include a wide 2 V to 36 V supply range, a differential input arrangement, an open-collector output, and a response time of 300 ns. The open-collector architecture requires an external pull-up resistor, but it provides useful flexibility because the output can be pulled to a system-defined voltage and the device can remain off during output high states. The input offset voltage can reach ±5 mV according to the published LM393 comparator information.

The architecture is suited to low- and moderate-speed threshold decisions. Its propagation delay is long compared with a high-speed logic comparator, but it is appropriate for monitoring, sorting, control, and protection functions that do not require sub-microsecond response. The differential inputs support sensing above or below a reference voltage, while the two channels can share a supply but operate independently.

Typical uses include battery monitoring, overvoltage detection, sensor signal conditioning, window comparison, temperature-control thresholds, and industrial control interfaces. In battery systems, the broad operating supply range allows the comparator to monitor divided supply voltages without requiring a low-voltage-only comparator.

When designing a PCB around the LM393AP, place input and pull-up components close to the device and keep sensitive comparator inputs away from switching nodes. Because the output is open collector, never leave an output undefined; fit the appropriate pull-up resistor to a compatible logic or supply rail. Verify differential input limits, output current, and common-mode range against the application’s worst-case voltage conditions.

This page combines device specifications, application guidance, same-package drop-in options, and a parameter-by-parameter comparison to support schematic review, PCB planning, and sourcing decisions.

جێگرەوەکانی جێگۆڕکێ بۆ LM393AP — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM393AP (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Package, Input Offset Voltage, Number of Comparators, Response Time.

Texas Instruments
Input Offset Voltage: 0.37 mV for LM2903B family
Number of Comparators: 2
Response Time: 1 us for LM2903B family
بەراوردکردن لەگەڵ LM393AP →
STMicroelectronics
Comparator Type: Dual independent precision voltage comparator
Package: 8-DIP
بەراوردکردن لەگەڵ LM393AP →
Texas Instruments
Comparator Type: Differential (general purpose)
Package: 8-PDIP (P) through-hole
Number of Comparators: 2 (dual)
بەراوردکردن لەگەڵ LM393AP →

LM393AN

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 8-pin PDIP
Dual independent precision voltage comparator · 2 channels · Single supply or split supply · Open-collector · Common-mode range extending to ground in single-supply operation · 8-DIP · 8 pins · Through-hole

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393P

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
Differential (general purpose) · 2 (dual) · Open-Collector · 2 V to 36 V · ±1 V to ±18 V · ±5 mV · 25 nA · 0.4 mA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393BP

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
B-version family offers lower offset voltage and supply current, with up to 36 V supply capability versus the original family

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2903P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin PDIP
Dual differential comparator · 2 · Open-collector · Rail-to-rail · 2 V minimum · Up to 38 V for LM2903B family · 0.37 mV for LM2903B family · 3.5 nA for LM2903B family

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903BP

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
B-version dual comparator with lower offset voltage and supply current, plus automotive-grade operating limits

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM393AP زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Comparator Type Dual differential comparator
Number of Channels 2 channels
Single-Supply Voltage Range 2 V to 36 V
Dual-Supply Voltage Range ±18 V
Propagation Delay 300 ns
جۆری دەرچوون Open-collector
Input Offset Voltage ±5 mV maximum
Output Sink Current 0.4 mA drain current
Power Dissipation 660 mW maximum
Differential Input Voltage Range ±38 V
پاکێج 8-pin PDIP
جۆری دامەزراندن Through-hole

ڕێکخستنی پینی LM393AP

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 OUT1 — Channel 1 open-collector output
پین 2 IN1- — Channel 1 inverting input
پین 3 IN1+ — Channel 1 non-inverting input
پین 4 GND — Ground connection
پین 5 IN2+ — Channel 2 non-inverting input
پین 6 IN2- — Channel 2 inverting input
پین 7 OUT2 — Channel 2 open-collector output
پین 8 VCC — Positive supply connection

بەکارهێنانە باوەکان

LM393AP گونجاوە بۆ 6 بەکارھێنانs: Battery Voltage Monitoring, Overvoltage Protection, Industrial Sensor Thresholding, Temperature Control Hysteresis, LED Bar-Level Detection, Open-Collector Logic Interface.

⚡

Battery Voltage Monitoring

The LM393AP fits battery threshold monitoring because its 2 V to 36 V operating range accommodates systems that operate from low-voltage cells through multi-cell packs. A resistor-divider network can scale the battery voltage into the differential input range, allowing the comparator to identify an undervoltage or overvoltage condition. Its 300 ns response is more than adequate for normal energy-storage supervision. Both open-collector outputs require pull-up resistors, allowing the fault signals to connect to a system logic rail or remain electrically isolated until needed. Designers should include input filtering where battery wiring can pick up noise and verify the divider values against the comparator’s input common-mode limits.

🛡️

Overvoltage Protection

LM393AP can implement a fast overvoltage indication by comparing a divided supply voltage against a reference threshold. The open-collector output can directly pull an enable, reset, or fault line low, which is useful when the protected circuit expects an active-low fault signal. With a 300 ns propagation delay, the comparator can react quickly to short-duration excursions, although filtering should be added where switching transients are expected. The external pull-up resistor must connect to a voltage compatible with both the receiving logic and the output isolation behavior. Board layout should keep the divider and threshold network away from inductors and high-current switching nodes.

🏭

Industrial Sensor Thresholding

The LM393AP is appropriate for industrial sensors whose outputs must be converted into digital threshold states, such as float switches, potentiometers, and resistive sensor bridges. A differential comparison reduces sensitivity to common input offsets, while the two independent channels can handle separate thresholds or implement a window detector. Its 300 ns response time supports moderately responsive process-control signals without imposing the power and complexity of a faster comparator. Because the output is open collector, a pull-up resistor is mandatory. For long sensor cables, protect the inputs against transients and maintain a low-impedance reference network close to the device.

🌡️

Temperature Control Hysteresis

LM393AP can implement temperature-control switching by comparing a temperature-derived voltage with a setpoint reference. Positive feedback can introduce hysteresis, preventing rapid output chatter when the measured temperature oscillates around the threshold. The dual-channel arrangement allows two independent switch points, such as separate heating and cooling outputs, or one channel can monitor a second safety limit. The comparator’s 2 V to 36 V supply range supports compatibility with many industrial control supplies. Use hysteresis resistors sized against input offset and noise, add local supply bypass capacitance, and verify that the sensor-reference network remains inside the allowed common-mode range over the complete temperature range.

💡

LED Bar-Level Detection

The two LM393AP channels can detect separate LED-bar thresholds or create a window comparator for a slowly changing analog signal. The open-collector outputs can each drive an LED through a current-limiting resistor and pull-up arrangement, or they can feed a digital indicator. Its 300 ns response is appropriate for visual indication rather than high-speed modulation. The wide 2 V to 36 V supply range permits operation from industrial control voltages, while the dual structure saves board area compared with two single comparators. Use the input offset rating of ±5 mV as one factor when choosing divider values and resistor tolerances, and add hysteresis to prevent indicator flicker near each switching threshold.

🔧

Open-Collector Logic Interface

LM393AP can serve as an open-collector interface between analog sensing circuitry and digital control hardware. Its output can sink current while remaining disconnected from the positive rail, allowing multiple devices to share a wired signal with an external pull-up. This arrangement is useful for simple alarm, interlock, and power-sequencing signals where active-low logic is acceptable. The 300 ns response is adequate for ordinary control signals and provides a defined transition after the differential input changes state. Confirm that the receiver recognizes the selected pull-up voltage and that the comparator’s sink-current limit remains below the required low-state current.

What are the key specifications of LM393AP that engineers should know?
The LM393AP is a dual differential comparator operating from 2 V to 36 V with a 300 ns response time and open-collector outputs. According to the Texas Instruments LM393 product page and the published device description, each channel can operate independently and the outputs require external pull-up resistors. The device is packaged in an 8-pin PDIP format. Its principal strengths are the wide supply range, dual-channel integration, and ability to pull outputs above the device supply through open-collector isolation.
Where can I download the LM393AP datasheet PDF?
The LM393AP datasheet can be obtained from the Texas Instruments LM393 product page at https://www.ti.com/product/LM393 and the orderable-parts link at https://www.ti.com/lit/gpn/lm393a. The manufacturer describes LM393B, LM2903B, LM193, LM293, LM393, and LM2903 as dual comparators. Use the orderable-parts document to confirm the exact LM393AP package, electrical limits, pin configuration, and ordering information for the 8-pin PDIP device.
Where can I find the LM393AP pinout?
The LM393AP pinout is available in the Texas Instruments LM393 datasheet, with the manufacturer product page located at https://www.ti.com/product/LM393. The 8-pin PDIP device uses pin 1 for OUT1, pins 2 and 3 for the first differential input, pin 4 for ground, pins 5 and 6 for the second differential input, pin 7 for OUT2, and pin 8 for the positive supply. Assign PCB tracks and input polarity directly from the manufacturer pin-description table.
Is LM393AP suitable for battery voltage monitoring?
Yes, the LM393AP is suitable for battery voltage monitoring because it operates from 2 V to 36 V. Resistors can divide the battery voltage into the differential input range, while the open-collector output can drive a fault indicator or digital control input through a pull-up resistor. Texas Instruments describes the device as a commercial-grade dual comparator with a 300 ns response, which is more than adequate for ordinary battery threshold alarms and power-management supervision.
Where can I buy LM393AP online and what is its current price?
Use the Request a Quote form on this page to request LM393AP availability, current pricing, and a quotation for the required quantity. The public listing identifies LM393AP as a Texas Instruments 8-pin PDIP dual comparator, but it does not provide an exact quantity-break price suitable for direct copying into structured pricing. The quotation team can confirm package readiness, current lead time, and the order quantity for your design.
What is the lead time for LM393AP?
The current LM393AP lead time and minimum order quantity should be confirmed through the Request a Quote form on this page. The device is listed as a Texas Instruments dual comparator in an 8-pin PDIP package, and its commercial availability can vary with order quantity and inventory. When requesting a quotation, identify the required quantity, target date, and whether you need tube, tray, or another approved shipping format.
Is LM393AP currently in stock?
Current LM393AP inventory status is best confirmed through the Request a Quote form on this page. Public listings identify the part and describe commercial availability, but inventory changes frequently and should not be treated as a guaranteed allocation. Provide your required quantity and target delivery date so the quotation team can confirm the latest stock position and production lead time.
What is the difference between LM393AP and LM393AN?
LM393AP and LM393AN are members of the same Texas Instruments LM393 dual-comparator family, but their orderable package suffixes differ. LM393AP is identified as an 8-pin PDIP device, while LM393AN is a distinct orderable entry shown in the cross-reference results. A replacement must match the physical footprint, pin arrangement, input common-mode limits, output sink capability, supply range, and temperature grade rather than relying on the family name alone.
LM393AP vs LM393P - which is better for a DIP-8 design?
LM393AP is the correct choice when the PCB requires the exact A-grade orderable designation and an 8-pin PDIP footprint. The verified comparison identifies LM393P as another 8-pin DIP comparator entry, but it does not establish that every electrical grade is identical. For a production redesign, compare the input common-mode range, propagation delay, offset voltage, supply current, temperature range, and qualification markings in the manufacturer documents before treating the two MPNs as interchangeable.
When should I choose LM393AP instead of LM393P?
Choose LM393AP when the bill of materials specifies that exact orderable part and the design uses an 8-pin PDIP footprint. Choose LM393P only after confirming that its grade, temperature range, common-mode input range, offset voltage, and other electrical limits meet the system requirements. Because both are dual-comparator DIP devices, the deciding factors are qualification and operating limits rather than board-level pin placement alone.
Is LM393AP suitable for industrial sensor interfaces?
Yes, LM393AP can be used for industrial sensor interfaces when its input and output limits match the sensing circuit. Its 2 V to 36 V supply range, differential inputs, and 300 ns response support threshold-based sensing of scaled sensor outputs. For noisy environments, use filtering, controlled grounding, and hysteresis at the input network. The open-collector output must receive a suitable pull-up resistor before it can drive a logic input reliably.
What can replace LM393AP in an existing 8-pin DIP circuit?
The closest documented replacements include LM393AN and LM393P from the Texas Instruments LM393 family, subject to package and electrical verification. A valid drop-in replacement must use the same 8-pin DIP footprint and preserve the differential-input and open-collector pin functions. Review common-mode range, differential voltage limits, propagation delay, output sink current, supply current, and temperature grade before substituting a part, especially in industrial or automotive equipment.
Is LM393AP the same as LM393B?
No, LM393AP and LM393B are related but not automatically identical orderable versions. Texas Instruments states that the B-version family provides lower offset voltage, lower supply current, higher supply-voltage capability, and improved ruggedness relative to the original LM393 family. A physical substitute is valid only when the exact package, pinout, input limits, output behavior, and environmental requirements are compatible.
What is the best cross-brand equivalent for LM393AP?
A cross-brand equivalent must provide a dual comparator in an 8-pin DIP package with the same differential-input and open-collector pin arrangement. The cross-reference results advise checking open-collector output and pinout evidence rather than assuming that every LM393-marked device is interchangeable. Confirm supply range, input common-mode limits, offset voltage, response time, output sink current, and temperature grade against the Texas Instruments datasheet before approving a substitute.
How should pull-up resistors be selected for LM393AP outputs?
Select the pull-up resistor according to the required output voltage, sink-current capability, rise-time limit, and current consumed while the output is low. The LM393AP output is open collector, so it can pull the node low but cannot actively drive it high. Place the resistor near the output or receiving logic input, verify that the low-state current remains within the comparator’s output limits, and calculate the RC rise time with the total capacitance connected to the node.
Does LM393AP need a bypass capacitor for stable operation?
Yes, a bypass capacitor should normally be placed close to the positive supply and ground pins to reduce supply noise and improve transient response. Follow the capacitor value and placement recommendations in the Texas Instruments LM393 datasheet, and keep the connection between the capacitor and the device pins short. The capacitor also helps prevent switching noise on the supply rail from changing the comparator decision near its threshold.

داتای سەرچاوەی ئەندازیاری بۆ LM393AP — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM393AP when the PCB requires an 8-pin PDIP dual comparator, a 2 V to 36 V supply range, and open-collector outputs for threshold detection or fault signaling. LM393AN and LM393P are same-family candidates when their exact grade and electrical limits satisfy the design, but the orderable suffix must be checked rather than inferred from the device name. LM393BP can be considered where the improved B-version offset and supply-current characteristics are useful, after verifying package and absolute-maximum requirements. LM2903P and LM2903BP are preferable when automotive temperature grading is required. For very low-voltage or low-power systems, a modern low-voltage comparator may consume less power and operate from a narrower supply than the LM393AP. Regardless of the selected MPN, preserve the differential-input and open-collector pin functions, include pull-up resistors, and verify common-mode range, response time, sink current, and temperature grade against the worst-case system conditions.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM393AN LM393P LM393BP LM2903P LM2903BP
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Comparator Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector

جیاکەرەوە سەرەکییەکان

  • Wide single-supply operating range (بەراورد بەLM393BP)
  • Dual independent comparator channels in one package (بەراورد بەLM201AD)
  • 300 ns response for general-purpose threshold detection (بەراورد بەTLV2402ID)

تێبینییەکانی دیزاین

Do not treat the open-collector outputs as actively driven logic outputs. Each output requires a pull-up resistor, and the resistor must connect to a rail compatible with the receiving device. Calculate the low-state sink current from the pull-up voltage and resistance, verify the output-current limit, and check the RC rise time at the connected load. Leaving either output without a pull-up can produce an undefined or slowly rising voltage.

Place the supply bypass capacitor directly between pins 8 and 4 with a short, low-inductance return path. Route both differential inputs away from switching nodes and keep the threshold or divider network close to pins 2, 3, 5, and 6. For sensitive sensor signals, use a grounded guard structure where practical and terminate long input traces close to the source to minimize capacitive pickup.

Add intentional hysteresis when the input can cross the threshold slowly or when noise may cause repeated output transitions. Positive feedback through a resistor can create a controlled switching gap, but the resistor value must account for the ±5 mV maximum input offset and the network impedances. Verify the resulting thresholds with the actual reference tolerance and signal source impedance rather than relying only on nominal resistor calculations.

Keep the supply within the 2 V to 36 V operating range and observe the differential input limit of ±38 V. Transients on industrial sensor lines can exceed those limits even when the main supply is controlled. Use suitable input clamping or series impedance where cables are exposed to noisy environments, and confirm that the absolute maximum ratings are not exceeded during power-up, shutdown, or fault conditions.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The LM393AP is identified as a commercial-grade general-purpose comparator. Specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 statements were not identified in the manufacturer or distributor information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm393ap datasheet LM393AP pinout LM393AP datasheet pdf Texas Instruments LM393AP LM393AP 36V comparator LM393AP 300ns response time LM393AP 8-pin PDIP LM393AP open collector output LM393AP battery monitoring LM393AP vs LM393P LM393AP drop-in replacement LM393AP price and stock LM393AP equivalent LM393AP application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM393AP LM393 LM393B LM2903 LM393AN LM393P LM393BP LM2903P LM2903BP dual differential comparator comparator analog comparator amplifier IC open-collector output voltage threshold detector 2 V to 36 V supply 300 ns propagation delay ±38 V differential input PDIP-8 DIP package through-hole package battery monitoring industrial sensor interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ