Texas Instruments

MAX232IN - Dual 120kbps RS-232 Transceiver | Texas Instruments

MPN: MAX232IN ✓ چالاک
5 V Vdss 8 mA typical Id 16-pin PDIP Package
MOQ: 1 |

MAX232IN گشتی

The Texas Instruments MAX232IN is a dual EIA-232 driver and receiver interface IC that operates from a single 5 V supply, supports data rates up to 120 kbit/s, and provides +9 V and -9 V RS-232 outputs. The device includes two drivers, two receivers, and an on-chip capacitive voltage generator, and is packaged in a 16-pin PDIP. According to the manufacturer product page, the MAX232 also provides ±2 kV electrostatic-discharge protection on the RS-232 lines.

An RS-232 transceiver is an interface IC that converts logic-level signals into voltage levels suitable for a serial communications link. Its hierarchy is transceiver > driver/receiver > interface IC > integrated circuit. The MAX232IN belongs to this category because it bridges a 5 V TTL or CMOS system and a ±9 V RS-232 port. It is useful when a controller, programmable logic, or test system needs bidirectional serial communication over longer distances than a logic-level UART connection can provide.

The principal features include two transmit channels, two receive channels, a maximum data rate of 120 kbit/s, receiver input tolerance of ±30 V, and low supply current of 8 mA typical. Its on-chip charge-pump circuit derives the negative RS-232 voltage required by the drivers, so the device needs only one 5 V supply rather than a separate negative supply. The ±2 kV ESD protection rating adds a useful layer of protection for exposed connector-facing pins.

The receivers convert RS-232 input voltages to TTL/CMOS logic levels and have a typical threshold of 1.3 V with 0.5 V typical hysteresis. The drivers convert TTL/CMOS logic inputs into RS-232 levels with +9 V and -9 V output capability. The combination of receiver hysteresis and input overvoltage tolerance helps distinguish valid signals from noise, while the dual-channel arrangement allows two RS-232 directions on one device.

Typical applications include legacy RS-232 equipment interfaces, industrial controller ports, point-of-sale equipment, data acquisition systems, and service or diagnostic ports. A MAX232IN can connect a 5 V microcontroller UART to a DB9 or equivalent RS-232 connector, provided the board also includes the connector, protection components, grounding strategy, and any required line-conditioning components.

The main design consideration is that the MAX232IN is a through-hole PDIP device and its charge-pump network requires the external capacitors specified by the manufacturer. Place those capacitors close to the supply and charge-pump pins, provide an uninterrupted ground path, and confirm signal levels and polarity at the connector. Although the receiver can accept ±30 V inputs, normal RS-232 operation still requires correct common-ground and cable arrangements.

This page combines verified manufacturer and distributor information with practical interface guidance, same-package replacement options, parameter comparisons, and design notes for engineers evaluating MAX232IN in legacy RS-232 designs.

جێگرەوەکانی جێگۆڕکێ بۆ MAX232IN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX232IN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Mounting Type, ESD Protection, Interface Standard.

Analog Devices
Package: 18-pin PDIP
Product Type: RS-232 transceiver
Mounting Type: Through-hole
بەراوردکردن لەگەڵ MAX232IN →
Linear Technology
Package: 18-pin CERDIP (J) - through-hole
Mounting Type: Through-Hole
بەراوردکردن لەگەڵ MAX232IN →
Texas Instruments
Package: SOIC-16 (D)
Mounting Type: Surface Mount
بەراوردکردن لەگەڵ MAX232IN →
Texas Instruments
Package: 16-SOIC, 3.90 mm body width
Product Type: Dual RS-232 driver/receiver transceiver
Mounting Type: Surface mount
بەراوردکردن لەگەڵ MAX232IN →
Texas Instruments
Package: 16-pin SOIC
Product Type: Dual RS-232 line-driver and receiver transceiver
Mounting Type: Surface mount
بەراوردکردن لەگەڵ MAX232IN →
Maxim Integrated
Product Type: Dual RS-232 line driver and receiver transceiver
Mounting Type: Surface mount
Interface Standard: EIA/TIA-232E
بەراوردکردن لەگەڵ MAX232IN →

MAX232EPE+

✅ جێگرەوەی ڕاستەوخۆ
📦 PDIP-16
Same 16-pin PDIP format; verified comparison reports no measurable primary-parameter differences, while detailed temperature and capacitor requirements remain to be confirmed.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

HIN232CPZ

✅ جێگرەوەی ڕاستەوخۆ
📦 PDIP-16
Same 16-pin PDIP format with consistent main performance parameters and terminal compatibility; operating-temperature and capacitor details require datasheet verification.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX232N

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-16
Dual RS-232 driver/receiver · 2 · 2 · 5 V · 120 kbit/s · ±9 V · ±30 V · 1.3 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX232IN تایبەتمەندییەکان

Product Type Dual EIA-232 driver/receiver transceiver
Number of Drivers 2
Number of Receivers 2
ڤۆڵتیەی دابینکردن 5 V
Maximum Data Rate 120 kbit/s
RS-232 Output Levels +9 V and -9 V
RS-232 Input Levels -30 V to +30 V
Receiver Threshold 1.3 V typical
Receiver Hysteresis 0.5 V typical
ئێستای دابینکردن 8 mA typical
ESD Protection ±2 kV
Charge-Pump Supply On-chip capacitive voltage generator
Logic Compatibility TTL/CMOS
پاکێج 16-pin PDIP
جۆری دامەزراندن Through Hole

ڕێنمایی ڕێکخستنی پینی MAX232IN 16-pin pdip

ڕێکخستنی پین بۆ MAX232IN (پاکێجی 16-pin pdip). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-pin pdip بۆ MAX232IN

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX232IN.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX232IN گونجاوە بۆ 6 بەکارھێنانs: Microcontroller RS-232 Debug Port, Industrial Equipment Control Interface, Point-of-Sale Terminal Interface, Data Acquisition System Communication, Legacy Serial Service Console, Instrumentation and Test Equipment.

🔧

Microcontroller RS-232 Debug Port

The MAX232IN fits a 5 V microcontroller debug or service port because it converts two logic-level UART channels into +9 V and -9 V RS-232 signals at rates up to 120 kbit/s. The transmitter path accepts TTL/CMOS drive levels, while the receiver path converts RS-232 inputs back to logic and tolerates inputs as high as ±30 V. Its on-chip charge-pump generator removes the need for a negative supply, leaving only the manufacturer-specified external capacitors. A practical implementation places the IC near the DB9 or terminal-block connector, routes each signal pair consistently, and provides a low-impedance ground connection. The 16-pin PDIP package is especially useful for through-hole prototypes and legacy industrial controllers.

🏭

Industrial Equipment Control Interface

The MAX232IN is appropriate for legacy industrial equipment that uses a 5 V RS-232 control link. Its dual-driver, dual-receiver arrangement supports two serial directions in one package, and the 120 kbit/s capability covers many configuration and command protocols. Receiver inputs accepted to ±30 V improve tolerance of voltage variation found on some long RS-232 connections, although correct grounding remains essential. The single 5 V supply and integrated charge-pump circuitry simplify system-level power design compared with discrete level-shifting networks. For an industrial deployment, engineers should verify the MAX232IN operating-temperature range against the equipment enclosure, add suitable external connector protection, and avoid relying on the internal ±2 kV ESD rating as a substitute for a complete surge-protection strategy.

🖥️

Point-of-Sale Terminal Interface

A point-of-sale terminal can use the MAX232IN to bridge a 5 V embedded controller to a conventional RS-232 peripheral. The two receive channels can accommodate status or acknowledgment lines, while the two transmit channels support command and data traffic. Operation up to 120 kbit/s is more than adequate for many legacy peripheral protocols, and the +9 V and -9 V driver outputs provide standard RS-232 signal levels. Because the interface uses a single 5 V supply, the controller board does not need a separate negative rail for level conversion. The principal layout requirement is to follow the datasheet charge-pump capacitor layout closely, keep the logic ground and RS-232 ground return connected appropriately, and place any selected protection components directly at the connector entry point.

📊

Data Acquisition System Communication

The MAX232IN can connect a data-acquisition controller or instrument to a host computer over a conventional RS-232 port. The 120 kbit/s rate supports configuration transfers and moderate command traffic, while the dual receiver arrangement allows more than one status input to be monitored. Receiver inputs can accept ±30 V, providing useful margin for legacy equipment with elevated signal levels. Its integrated charge pump eliminates the external negative supply and discrete transistor stages that would otherwise increase board complexity. Designers should treat the MAX232IN as a line interface rather than a complete isolation solution: if the remote equipment is at a different ground potential, use an approved isolation method and separately verify the transceiver’s common-mode limits. The 16-pin PDIP footprint is convenient for laboratory and legacy-control boards.

💻

Legacy Serial Service Console

The MAX232IN is well matched to a service-console or configuration interface that must communicate with older RS-232 equipment. Two driver outputs and two receiver inputs provide bidirectional communication without requiring separate level-conversion ICs. The device operates from 5 V, supports communication up to 120 kbit/s, and generates the required negative RS-232 voltage internally. Its through-hole PDIP package makes it practical for service boards built with plated-through-hole techniques or for adding an RS-232 port to an existing controller assembly. For reliable field use, include a defined ground conductor in the cable, verify the logic polarity of each signal, and consider external protection because the manufacturer-stated ±2 kV ESD rating applies to the integrated interface but does not eliminate the need to assess the complete cable and enclosure environment.

🔬

Instrumentation and Test Equipment

The MAX232IN can provide a standard RS-232 control port on laboratory and test equipment built around 5 V logic. Its receiver threshold of 1.3 V typical and 0.5 V typical hysteresis help reject noise around the switching region, while the ability to accept ±30 V inputs provides compatibility with older test equipment. The device supports communication rates up to 120 kbit/s and presents a straightforward two-channel interface to a controller. For instrumentation, minimize the distance between the IC and connector, follow the specified charge-pump capacitor arrangement, and keep switching regulators and high-current return paths away from the receiver traces. The exposed through-hole package also makes the design straightforward to inspect and service, although its footprint may be larger than modern surface-mount alternatives in compact instruments.

کورتەی بەرهەمە پێشنیارکراوەکان

MAX232IN Texas Instruments بەکارهێنراوە لە: Microcontroller RS-232 Debug Port, Industrial Equipment Control Interface, Point-of-Sale Terminal Interface, Data Acquisition System Communication, Legacy Serial Service Console, Instrumentation and Test Equipment HIN232CPZ Cross-brand RS-232 interface candidate بەکارهێنراوە لە: Microcontroller RS-232 Debug Port, Legacy Serial Service Console MAX232EPE+ Same-package replacement candidate بەکارهێنراوە لە: Industrial Equipment Control Interface, Data Acquisition System Communication MAX232N Texas Instruments بەکارهێنراوە لە: Point-of-Sale Terminal Interface, Instrumentation and Test Equipment
What is the MAX232IN and what does it do?
The MAX232IN is a dual-channel RS-232 driver and receiver interface IC that converts between 5 V TTL/CMOS logic and RS-232 voltage levels. According to the Texas Instruments manufacturer datasheet, it contains two drivers, two receivers, and a capacitive voltage generator, allowing a single 5 V supply to produce the positive and negative voltages required by an RS-232 link.
What is the operating voltage of MAX232IN?
The MAX232IN operates from a single 5 V supply. According to the Texas Instruments manufacturer datasheet, its on-chip capacitive voltage generator derives the negative voltage used by the RS-232 drivers, eliminating the need for a separate negative supply in a conventional MAX232 implementation. The manufacturer product page identifies the device as a 5 V dual-channel RS-232 line driver and receiver.
What is the maximum data rate of MAX232IN?
The MAX232IN supports data rates up to 120 kbit/s. The Texas Instruments manufacturer product page explicitly identifies the device as a 5 V dual-channel 120 kbit/s RS-232 line driver and receiver. This rating is adequate for legacy RS-232 ports, UART links, and equipment-control interfaces operating below that maximum rate.
Where can I download the MAX232IN datasheet PDF?
The official MAX232IN datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/max232.pdf. The manufacturer page for MAX232 is also available at https://www.ti.com/product/MAX232. These official links provide the device description, ordering information, electrical characteristics, and package details needed for design verification.
Where can I find the MAX232IN pinout?
The MAX232IN pinout is published in the Texas Instruments MAX232 manufacturer datasheet at https://www.ti.com/lit/ds/symlink/max232.pdf. The MAX232IN uses a 16-pin PDIP package, so the pin arrangement and pin-numbering diagram should be checked against the package drawing before PCB layout or replacement work. DigiKey also identifies the MAX232IN as a 16-pin PDIP RS-232 transceiver.
What are the key specifications of MAX232IN that engineers should know?
The key MAX232IN specifications are a single 5 V supply, operation up to 120 kbit/s, two drivers, two receivers, +9 V and -9 V outputs, receiver inputs accepted to ±30 V, 8 mA typical supply current, and ±2 kV ESD protection. According to the Texas Instruments manufacturer datasheet and product page, the receiver threshold is 1.3 V typical and its hysteresis is 0.5 V typical.
What RS-232 output voltage does MAX232IN produce?
The MAX232IN produces ±9 V RS-232 output levels from a 5 V supply. According to the Texas Instruments manufacturer product page, each of its two drivers converts TTL or CMOS input levels into the positive and negative voltage levels expected by an RS-232 receiver. The on-chip capacitive voltage generator supplies the negative output voltage required by the driver stage.
Can MAX232IN withstand ±30 V receiver inputs?
Yes, the MAX232IN receivers can accept input voltages from -30 V to +30 V. According to the Texas Instruments manufacturer datasheet, the receiver input tolerance is ±30 V, while the typical logic threshold is 1.3 V and typical hysteresis is 0.5 V. Input tolerance does not eliminate the need for correct ground references or external surge protection.
What can replace MAX232IN without changing the PCB?
A true PCB-compatible replacement must use the same 16-pin PDIP footprint, match the pin assignments, and provide compatible RS-232 voltage levels and data-rate capability. The verified cross-reference data identifies MAX232EPE+ and HIN232CPZ as candidate 16-pin PDIP replacements, but each replacement still requires validation against its manufacturer datasheet for pinout, capacitor requirements, temperature range, and lifecycle status before production use.
Is MAX232IN the same as MAX232EPE+?
The MAX232IN and MAX232EPE+ are presented as functionally comparable dual RS-232 driver/receiver devices in the same 16-pin PDIP package class, but interchangeability requires a complete datasheet review. The verified comparison reports no measurable primary-parameter differences, yet engineers should still confirm pin names, charge-pump capacitor values, temperature limits, supply-current limits, and qualification status before treating either part as a drop-in replacement.
When should I choose MAX232IN over another dual RS-232 transceiver?
Choose MAX232IN when the design needs a legacy-compatible 16-pin PDIP RS-232 interface operating from 5 V at up to 120 kbit/s. It is particularly suitable when a through-hole retrofit or existing board must remain unchanged. A newer surface-mount package may be preferable for new compact designs, while an automotive or extended-temperature requirement calls for a part with the appropriate qualification and temperature data.
Is MAX232IN suitable for an industrial RS-232 controller port?
The MAX232IN can be suitable for an industrial controller port when the interface operates within its 5 V supply and 120 kbit/s limits and the system provides the required external charge-pump capacitors. Its receivers tolerate ±30 V inputs and the manufacturer lists ±2 kV ESD protection. Industrial suitability still depends on the verified operating-temperature range, which was not included in the supplied data.
Where can I buy MAX232IN online and how much does it cost?
The MAX232IN can be purchased from Texas Instruments or authorized distributors, with DigiKey and LCSC listings available in the verified data. LCSC displayed a starting price of $1.4248 as of 2026-10-28, while another LCSC result showed $1.4487; the difference may reflect stock, quantity, or listing updates. Confirm quantity breaks, lead time, and current inventory before ordering.
What is the lead time and stock status for MAX232IN?
The supplied data identifies MAX232IN listings as in stock at LCSC and available through multiple distributors, but it does not provide a numeric factory lead time or a dated XAIPART inventory count as of 2026-10-28. Because availability can change, buyers should verify the requested quantity and lead time directly with the selected distributor before committing the part to a production schedule.
What is the best cross-brand equivalent for MAX232IN?
HIN232CPZ is the best-supported cross-brand candidate in the supplied web data because it is described as a 16-pin PDIP replacement with consistent main performance characteristics and terminal compatibility. However, it should not be treated as an automatic drop-in until its pinout, operating-temperature range, charge-pump capacitor network, ESD rating, and lifecycle status are checked against the MAX232IN datasheet.

داتای سەرچاوەی ئەندازیاری بۆ MAX232IN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the MAX232IN for a legacy 5 V RS-232 interface that uses a 16-pin PDIP footprint and requires two transmit and two receive channels. Its verified 120 kbit/s operating rate, +9 V and -9 V outputs, ±30 V receiver tolerance, and integrated charge-pump generator make it a straightforward choice for retrofit and through-hole industrial boards. Consider MAX232EPE+ when the verified no-measurable-difference comparison satisfies your sourcing requirements, but still check temperature limits, external capacitor values, lifecycle status, and pin labels. Consider HIN232CPZ as a cross-brand candidate with consistent reported terminal and performance characteristics, while completing the same engineering validation. For new compact surface-mount products, a modern smaller-package transceiver may offer better board-area efficiency, but it will not be a physical drop-in replacement. Do not select any candidate solely by package count; verify the exact pinout, charge-pump network, logic polarity, and environmental requirements.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX232EPE+ HIN232CPZ MAX232N
Package 16-pin PDIP 16-pin PDIP - same package 16-pin PDIP - same package 16-pin PDIP - same package
Brand Texas Instruments Maxim Integrated Intersil Maxim Integrated
Device Type Dual RS-232 driver/receiver Dual RS-232 driver/receiver Dual RS-232 driver/receiver Dual RS-232 driver/receiver
Number of Drivers 2 2 2 2
Number of Receivers 2 2 2 2

جیاکەرەوە سەرەکییەکان

  • Verified through-hole dual RS-232 interface (بەراورد بەMAX232EPE+)
  • Documented ±2 kV ESD protection (بەراورد بەHIN232CPZ)
  • Integrated single-supply charge-pump design (بەراورد بەMAX232N)

تێبینییەکانی دیزاین

Place the charge-pump capacitors and bypass capacitor close to their associated MAX232IN pins, following the manufacturer datasheet layout and values exactly. Keep the two driver outputs away from the receiver inputs and logic traces to reduce feedthrough from RS-232 transitions. Because this is a through-hole PDIP device, pay particular attention to lead spacing, connector alignment, and adequate mechanical clearance on through-hole industrial boards.

Do not substitute MAX232IN with an arbitrary surface-mount RS-232 transceiver on an existing board. A valid replacement must match the 16-pin PDIP footprint, pin functions, charge-pump capacitor requirements, input levels, data rate, and operating-temperature range. Also verify whether the transmitted signal is active-high or inverted; installing a pin-compatible electrical device without checking polarity can leave a UART port physically correct but unable to communicate.

Route the two RS-232 outputs as a matched pair where practical and keep them away from sensitive analog or high-speed clock traces. The MAX232IN drivers switch to approximately +9 V and -9 V, so their transitions can couple into nearby circuitry even though the receiver uses 1.3 V typical threshold and 0.5 V typical hysteresis. A solid ground plane, short return path, and connector-side protection improve noise immunity.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied verified data does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The MAX232 is a general-purpose commercial interface IC, so AEC-Q100 is not applicable based on the supplied information.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX232IN datasheet PDF Texas Instruments MAX232IN MAX232IN 120kbps dual RS-232 transceiver MAX232IN 16-pin PDIP MAX232IN RS-232 pinout MAX232IN microcontroller UART interface MAX232IN industrial RS-232 port MAX232IN vs MAX232EPE+ MAX232IN drop-in replacement MAX232IN price and stock where to buy MAX232IN online what can replace MAX232IN MAX232IN ±2kV ESD protection single 5V dual RS-232 driver receiver

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments MAX232IN MAX232 MAX232EPE+ HIN232CPZ MAX232N RS-232 EIA-232 TIA/EIA-232-F RS-232 transceiver driver/receiver interface IC integrated circuit TTL CMOS UART capacitive voltage generator charge-pump capacitor PDIP-16 surface-mount RS-232 alternative 120 kbit/s ±2 kV ESD protection ±30 V input tolerance industrial equipment interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ