MAX232N - 5V Dual RS-232 Transceiver | Texas Instruments
MPN: MAX232N ✓ چالاکMAX232N گشتی
An RS-232 interface transceiver is an interface IC that converts low-voltage digital logic levels into the bipolar voltage levels required by RS-232, then converts received bipolar signals back into TTL or CMOS levels. In the product hierarchy, the MAX232N belongs to the RS-232 transceiver class within interface ICs. The dual-channel architecture supports two simultaneous communication paths, while the integrated voltage generator eliminates the need for a separate negative supply rail.
The MAX232N's principal features include support for data rates up to 120 kbit/s, two transmit channels, two receive channels, ±30 V receiver input tolerance, and ±2 kV ESD protection. Its capacitive voltage generator produces the negative voltage required by the RS-232 drivers from a single 5 V supply. The receiver threshold is typically 1.3 V with approximately 0.5 V hysteresis, helping reject noise while resolving valid logic states.
The MAX232N combines TTL/CMOS-compatible inputs and outputs with RS-232 line-driver outputs. According to the manufacturer datasheet, the receivers accept signals as high as ±30 V, while the drivers produce approximately ±9 V output levels. This combination is useful when a system must tolerate legacy serial connectors, ground-potential differences, or electrostatic-discharge exposure while maintaining a conventional 5 V logic interface.
Typical uses include industrial serial controllers, service equipment, data-acquisition systems, point-of-sale terminals, and legacy computer serial ports. The 120 kbit/s maximum data rate suits asynchronous RS-232 links that operate below high-speed differential-interface rates. The two-driver, two-receiver arrangement can also implement one bidirectional data path and one unidirectional status path, or two lower-speed channels.
Designers should provide the charge-pump capacitors specified by the manufacturer and connect the interface connector through protection components suited to the required ESD and surge environment. The device is not a multi-drop RS-232 solution, and cable length, termination, grounding, and logic levels must be checked against the target system rather than inferred only from the 120 kbit/s headline specification.
This page consolidates the verified manufacturer and distributor information, same-package replacement guidance, and practical interface-design considerations for engineers evaluating the MAX232N. It also distinguishes documented MAX232N characteristics from package or lead-time details that were not supplied by the retrieved sources.
جێگرەوەکانی جێگۆڕکێ بۆ MAX232N — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX232N (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Supply Voltage, Interface Standard, ESD Protection.
MAX232CPE
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX232DPE
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX232EPE
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX232AEPE
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM232AAN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX232N تایبەتمەندییەکان
| Device Type | Dual RS-232 driver/receiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| ڤۆڵتیەی دابینکردن | 5 V |
| Maximum Data Rate | 120 kbit/s |
| Driver Output Voltage | ±9 V |
| Receiver Input Voltage Tolerance | ±30 V |
| Receiver Typical Threshold | 1.3 V |
| Receiver Typical Hysteresis | 0.5 V |
| ESD Protection | ±2 kV |
| Voltage Generation | On-chip capacitive voltage generator |
| ئێستای دابینکردن | 8 mA typical |
| Interface Standard | TIA/EIA-232-F |
| Recommendation | ITU V.28 |
| پاکێج | 16-pin PDIP |
| جۆری دامەزراندن | Through-hole |
| Logic Compatibility | TTL/CMOS |
ڕێنمایی ڕێکخستنی پینی MAX232N 16-pin pdip
ڕێکخستنی پین بۆ MAX232N (پاکێجی 16-pin pdip). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX232N.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX232N گونجاوە بۆ 6 بەکارھێنانs: Industrial Serial Controller Interface, Point-of-Sale Terminal Connectivity, Data-Acquisition Equipment, Legacy Computer Serial Port, Service and Diagnostic Equipment, Communication and Networking Equipment.
Industrial Serial Controller Interface
The MAX232N fits legacy industrial controllers that expose a 5 V TTL/CMOS UART as an RS-232 port. Its two drivers and two receivers permit two RS-232 channels, while operation up to 120 kbit/s covers common asynchronous control protocols. The integrated capacitive voltage generator derives negative driver voltage from one 5 V supply, avoiding a separate negative rail. Designers should still verify industrial temperature requirements, isolate ground differences, and add connector-side surge protection for long cables.
پێشنیارکراو
Point-of-Sale Terminal Connectivity
Point-of-sale peripherals commonly use RS-232 where the host runs at TTL logic levels and the peripheral cable reaches outside the equipment enclosure. The MAX232N converts two UART directions to approximately ±9 V RS-232 levels at rates up to 120 kbit/s, and its receivers tolerate inputs up to ±30 V. Its single 5 V supply simplifies system power design, while the transmitter and receiver count can support separate data and status lines. ESD protection is ±2 kV, so additional connector protection may be appropriate for exposed installations.
پێشنیارکراو
Data-Acquisition Equipment
The MAX232N can connect a data-acquisition controller to legacy measurement equipment using a wired RS-232 link. Its 120 kbit/s operating limit is suitable for many instrument-control and status-reporting channels, and the ±30 V receiver tolerance improves robustness when exposed to larger bipolar input excursions. The two transmitters and two receivers allow concurrent command and response traffic on separate pairs. Designers should minimize cable-loop area, maintain compatible signal grounds, and select data rates that remain reliable over the installed cable length.
پێشنیارکراو
Legacy Computer Serial Port
The MAX232N is suitable for adding an RS-232 port to a modern controller board that retains a legacy PC or peripheral DB9 connector. It provides the required TIA/EIA-232-F line levels from a 5 V logic system at up to 120 kbit/s, with ±2 kV ESD protection on the interface. The 16-pin PDIP package is straightforward to assemble but occupies more board area than modern surface-mount transceivers. Firmware must also configure the UART baud rate and parity to match the connected device.
پێشنیارکراو
Service and Diagnostic Equipment
Service technicians often connect older test instruments, programming fixtures, or configuration tools through RS-232. The MAX232N supports 120 kbit/s communication and uses two full driver/receiver channels, allowing a fixture to exchange commands and status without adding another level-shifting device. Receiver inputs can withstand ±30 V, which helps separate logic signals from line-side transients. A production fixture should include defined connector wiring, ground reference, and suitable fault protection rather than assuming every RS-232 port uses the same signal polarity.
پێشنیارکراو
Communication and Networking Equipment
The MAX232N can provide a point-to-point management or control channel in communications equipment that still uses RS-232. The 120 kbit/s maximum data rate is appropriate for configuration links, status reporting, and low-bandwidth service interfaces rather than bulk network traffic. Two driver/receiver pairs can support two point-to-point links, and the single 5 V supply reduces system-level power complexity. Installations should account for RS-232 ground-offset limitations, control electrostatic-discharge exposure at the connector, and avoid assuming that the interface replaces a differential network transceiver.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX232N — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX232CPE | MAX232DPE | MAX232EPE | MAX232AEPE | ADM232AAN |
|---|---|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP - same | 16-pin PDIP - same | 16-pin PDIP - same | 16-pin PDIP - same | 16-pin PDIP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Device Type | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver | Dual RS-232 driver/receiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
جیاکەرەوە سەرەکییەکان
- Exact MAX232N sourcing identity (بەراورد بەMAX232CPE)
- Documented line-side input robustness (بەراورد بەADM232AAN)
- Single-supply RS-232 conversion (بەراورد بەMAX232AEPE)
تێبینییەکانی دیزاین
Route the RS-232 driver and receiver nets directly to the connector-side protection network, and keep the MAX232N logic-side traces away from those nets. The 120 kbit/s capability does not eliminate susceptibility to external cable transients, so maintain practical spacing between the bipolar interface and sensitive logic or clock routes. Place the required charge-pump capacitors close to their associated device pins and follow the exact capacitor values and polarity shown in the manufacturer datasheet.
Do not substitute the generated RS-232 supply rails for the logic supply or connect the charge-pump capacitor pins incorrectly. The MAX232N derives negative driver voltage from a single 5 V supply, and incorrect capacitor connection can prevent valid ±9 V outputs. Also verify connector pin numbering and signal direction at the assembled board because RS-232 DB9 implementations can differ. Confirm whether the application requires hardware handshake lines before relying on the two available driver and receiver channels.
Use the shortest practical path between the transceiver and the serial connector, and place any approved series impedance, clamping, or protection components directly at the connector entry. The integrated ±2 kV ESD rating does not automatically cover larger surge events. For long or industrial cables, evaluate ground offsets, common-mode noise, and an external protection network using application-specific surge requirements rather than treating the IC rating as a complete connector-protection solution.
زانیاری پابەندبوون
The supplied verified sources do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for MAX232N. The part is an industrial-capable interface IC, but no AEC-Q100 qualification was identified in the provided data.