MAX3380EEUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MPN: MAX3380EEUP+T ✓ چالاکMAX3380EEUP+T گشتی
An RS-232 transceiver is an interface IC that converts between single-ended RS-232 signals and TTL/CMOS-compatible logic. The MAX3380EEUP+T operates as a full-duplex interface with two transmit drivers and two receive receivers, allowing simultaneous bidirectional communication when the connected system provides the required ground and signal arrangement. Its low-power design is intended for portable instruments, data-cable applications, and embedded systems using mixed logic voltage levels.
The device accepts supply voltages from +2.35V to +5.5V. The MAX3380EEUP+T uses a VL reference pin to support mixed-logic systems down to +1.65V, while the datasheet identifies the device as a +2.35V to +5.5V-powered EIA/TIA-232 and V.28/V.24 communication interface. The operating data rate reaches 460 kbps, which is suitable for higher-speed serial links used in instrumentation, industrial controls, and equipment interfaces.
Its integrated protection is a key differentiator for external cable connections. The I/O and logic pins are specified for ±15 kV ESD protection, reducing the need for separate protection networks when the board layout follows the manufacturer's recommended connection guidance. The transceiver family also provides low power requirements and is designed for applications involving RS-232 cables, data acquisition, test equipment, and industrial control systems.
Typical uses include RS-232 interfaces on laboratory instruments, point-of-sale terminals, industrial controllers, data loggers, and service equipment. The two transmitter and two receiver channels make it appropriate for systems that need more than one serial port or a full-duplex connection. The TSSOP-20 package supports compact surface-mount assembly while exposing the individual driver, receiver, logic-reference, supply, and ground connections required for a complete interface.
When laying out the board, keep RS-232-side traces away from sensitive analog and logic signals, connect the transceiver supply and ground pins with low-inductance paths, and follow the datasheet recommendations for decoupling and external protection. Confirm the VL voltage before connecting the logic-side circuitry, especially when the host controller operates below the transceiver supply voltage.
This product page combines the manufacturer specifications with practical interface considerations, package guidance, application examples, and drop-in alternatives. It helps engineers evaluate the MAX3380EEUP+T for data-cable equipment, industrial electronics, and embedded serial communication before completing the PCB footprint and protection strategy.
جێگرەوەکانی جێگۆڕکێ بۆ MAX3380EEUP+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3380EEUP+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Supply Voltage Range, Interface Standard, Communication Standard, ESD Protection, Receiver Count.
MAX3380EEUP+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3380EEUP-T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3380ECUP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3380EEUP+T تایبەتمەندییەکان
| Product Type | RS-232 transceiver |
| Transmitter Count | 2 transmitters |
| Receiver Count | 2 receivers |
| Supply Voltage Range | +2.35V to +5.5V |
| Maximum Data Rate | 460 kbps |
| Logic Reference Voltage | Down to +1.65V |
| ESD Protection | ±15 kV on I/O and logic pins |
| Communication Standard | EIA/TIA-232 and V.28/V.24 |
| Duplex Operation | Full duplex |
| Package Type | 20-pin TSSOP |
| جۆری دامەزراندن | Surface mount |
| ئێستای ئارام | 1 µA |
| I/O Protection | ±15 kV ESD protected |
| Logic Pin Protection | ±15 kV ESD protected |
ڕێنمایی ڕێکخستنی پینی MAX3380EEUP+T 20-pin tssop
ڕێکخستنی پین بۆ MAX3380EEUP+T (پاکێجی 20-pin tssop). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3380EEUP+T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX3380EEUP+T گونجاوە بۆ 6 بەکارھێنانs: Laboratory Instrument Serial Interface, Industrial Controller RS-232 Port, Data-Cable Equipment Connection, Portable Measurement Equipment, Point-of-Sale Terminal Interface, Embedded Service and Configuration Port.
Laboratory Instrument Serial Interface
The MAX3380EEUP+T fits RS-232 connections on laboratory instruments because it provides two transmitters, two receivers, and a 460 kbps maximum data rate in a compact 20-pin TSSOP. Place the transceiver between the instrument controller and an external RS-232 port, using the VL pin to match the controller's logic voltage when it is below the +2.35V to +5.5V transceiver supply range. The ±15 kV ESD protection on I/O and logic pins adds useful defense for a connector exposed to operator-accessible cabling. Confirm the cable length, ground arrangement, and host logic levels before finalizing the interface.
پێشنیارکراو
Industrial Controller RS-232 Port
The MAX3380EEUP+T is appropriate for an industrial controller that must communicate with legacy RS-232 equipment while operating from a compact mixed-logic supply. Its +2.35V to +5.5V supply range and VL reference down to +1.65V allow the interface logic to follow a lower-voltage controller. The 2Tx/2Rx full-duplex arrangement supports equipment that exchanges commands and status simultaneously, while 460 kbps operation provides adequate throughput for supervisory and configuration traffic. Use a protected connector path and verify grounding and signal polarity during board integration.
پێشنیارکراو
Data-Cable Equipment Connection
The MAX3380EEUP+T is designed for data-cable equipment requiring a protected RS-232 interface. Its integrated ±15 kV ESD protection on I/O and logic pins is directly relevant when the serial connector is connected to an external cable. The two transmit and two receive channels allow a board to implement multiple RS-232 paths or a full-duplex link within a limited footprint. A 20-pin TSSOP package supports compact surface-mount assembly, and the +2.35V to +5.5V operating range accommodates several embedded logic systems. Preserve the recommended decoupling and controlled return paths at the connector.
پێشنیارکراو
Portable Measurement Equipment
The MAX3380EEUP+T supports portable measurement equipment because it combines a 1 µA quiescent-current option, compact TSSOP packaging, and a 460 kbps RS-232 interface. The low-power operating characteristic is useful in battery- or USB-powered instruments where the serial interface must remain efficient without dominating the power budget. The VL pin permits the host controller to operate with logic thresholds down to +1.65V. For external probe or service connections, the integrated ±15 kV ESD protection provides an additional layer of robustness, although chassis grounding and connector design remain important.
پێشنیارکراو
Point-of-Sale Terminal Interface
The MAX3380EEUP+T can serve as the RS-232 interface in a point-of-sale terminal that must connect a low-power embedded controller to receipt printers, scanners, or other legacy peripherals. The two transmitters and two receivers support both command transmission and peripheral-status reception, and the 460 kbps rate is sufficient for typical transaction traffic. Its ±15 kV ESD protection is valuable at the external equipment connector, while the 20-pin TSSOP footprint supports compact board layouts. Confirm whether each peripheral requires full-duplex wiring or only one direction before assigning the channels.
پێشنیارکراو
Embedded Service and Configuration Port
The MAX3380EEUP+T fits embedded equipment that exposes a service or configuration port for diagnostics, firmware loading, or parameter adjustment. The full-duplex 2Tx/2Rx arrangement lets the controller exchange data while the host remains active, and the interface operates from +2.35V to +5.5V with logic thresholds referenced through VL. A 460 kbps maximum rate allows faster transfers than a slow character-only console. For field-accessible equipment, route the protected connector through the recommended layout and use the ±15 kV I/O and logic-pin protection as part of a broader electrostatic-discharge design.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX3380EEUP+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX3380EEUP | MAX3380EEUP-T | MAX3380ECUP |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin TSSOP | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same |
| Product Type | 2Tx/2Rx RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Transmitter and Receiver Count | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers |
جیاکەرەوە سەرەکییەکان
- Directly replaceable ordering variant (بەراورد بەMAX3380EEUP)
- Active lifecycle position (بەراورد بەMAX3380ECUP)
- Mixed-logic support in a compact interface (بەراورد بەMAX3380EEUP-T)
تێبینییەکانی دیزاین
Do not treat the MAX3380EEUP+T supply voltage and VL logic-reference voltage as interchangeable. The transceiver operates from +2.35V to +5.5V, while the VL pin allows the logic side to interoperate with systems down to +1.65V. Set VL according to the host controller's levels and follow the manufacturer pin-description table before assigning the logic-side signals.
Place the transceiver and its required bypass capacitors close to the supply and ground pins. Route RS-232 driver outputs directly toward the connector and keep logic-side traces away from cable-side nets. Preserve a low-impedance return path between the transceiver ground and connector ground, and use the manufacturer's recommended application circuit as the reference for the VL and protection connections.
RS-232 edges can radiate or couple into nearby circuitry even when the logic side operates at low voltage. Keep the 2Tx/2Rx cable-side nets short where practical, avoid routing them beneath sensitive analog sections, and maintain separation from clocks, sensors, and reference nodes. The integrated ±15 kV ESD protection improves survivability but does not replace controlled cable routing, grounding, or connector design.
زانیاری پابەندبوون
The product information identifies the MAX3380E family as production, but no explicit compliance declaration is included in the cited listings. AEC-Q100 is not applicable because this is an interface IC rather than an automotive-qualified component.