MAX338ESE+T - 8:1 CMOS Analog Multiplexer | Analog Devices
MPN: MAX338ESE+T ✓ چالاکMAX338ESE+T گشتی
An analog multiplexer is an analog switch that routes one of several input signals to a shared output. The MAX338 belongs to the broader hierarchy of CMOS analog switch, multiplexer, interface IC, and semiconductor devices. Its eight channels are selected by a 3-bit binary address, while an enable input provides control over the selected connection. The device can therefore operate as a multiplexer or serve as a demultiplexer when the direction of signal routing is reversed.
The MAX338/MAX339 family uses Maxim's 44 V silicon-gate process. This process supports operation from a single +4.5 V to +30 V supply or from dual ±4.5 V to ±20 V supplies. All address and enable controls remain TTL-compatible over their specified ranges, with a +0.8 V to +2.4 V input threshold identified for the control inputs. These characteristics make the multiplexer suitable for systems that must route wide-range analog signals.
The 400 ohm on-state resistance identifies the MAX338 as a low-leakage CMOS multiplexer option intended for precision signal routing rather than high-current power switching. Its eight-to-one configuration reduces the number of physical connections required when several measured or conditioned signals must reach one processing channel. The common output architecture can also simplify board routing when a controller selects among sensor, instrument, or test-point signals.
Typical applications include automated test equipment, data-acquisition systems, instrumentation, industrial control, and measurement setups. In each case, the 3-bit address bus identifies the desired channel and the enable input controls whether the common output is connected. The part is particularly useful where one analog input must be presented to a shared amplifier, converter, or measurement circuit without duplicating that downstream circuitry.
A key design consideration is that the MAX338 is not a power switch. Its 400 ohm on-state resistance contributes signal attenuation and, when driving a finite load, can introduce an interaction between switch resistance and downstream input impedance. Layout should keep analog traces short, maintain a stable return path, and avoid placing high-current switching nodes near the selected input channels.
This page consolidates the manufacturer's supply-range information, package details, functional characteristics, verified alternatives, and practical routing guidance into an engineering-focused guide for selecting and implementing the MAX338ESE+T in high-voltage analog multiplexing systems.
جێگرەوەکانی جێگۆڕکێ بۆ MAX338ESE+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX338ESE+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Multiplexer Configuration, Number of Channels, Address Control, Process Technology.
MAX338CSE+T
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX338MSE/PR3+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX338ESE+T تایبەتمەندییەکان
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| On-State Resistance | 400 ohm |
| Single Supply Voltage Range | +4.5 V to +30 V |
| Dual Supply Voltage Range | ±4.5 V to ±20 V |
| Address Control | 3-bit binary |
| TTL-Compatible Control Threshold | +0.8 V to +2.4 V |
| Process Technology | 44 V silicon-gate CMOS |
| Number of Channels | 8 channels |
| پاکێج | 16-SOIC |
| Package Width | 3.90 mm |
| Delivery Format | Tape and reel |
| Multiplexer or Demultiplexer Operation | Configurable by signal-routing arrangement |
| Pin-Configurable Replacement Reference | DG508A and DG509A industry-standard devices |
ڕێنمایی ڕێکخستنی پینی MAX338ESE+T 3.90 mm
ڕێکخستنی پین بۆ MAX338ESE+T (پاکێجی 3.90 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX338ESE+T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX338ESE+T گونجاوە بۆ 6 بەکارھێنانs: Automated Test Equipment, Data Acquisition Systems, Industrial Process Monitoring, Precision Instrumentation, Battery-Powered Measurement, Interface Signal Routing.
Automated Test Equipment
The MAX338ESE+T fits automated test systems that must route multiple analog test points to a shared measurement channel. Its 8:1 configuration uses a 3-bit address to select one of eight inputs, reducing the number of signal-conditioning paths required on the motherboard. The 400 ohm on-state resistance is relevant when the selected source sees a finite input impedance, while the single +4.5 V to +30 V supply range supports higher-voltage instrumentation. Keep the common output and selected input routing short, and account for switch resistance when setting gain and input-impedance limits.
Data Acquisition Systems
In a data-acquisition system, the MAX338ESE+T can present eight conditioned analog inputs to one converter or amplifier through a common output. This arrangement is useful when several sensors share a measurement front end but must be selected under digital control. The 3-bit binary address simplifies sequencing, and TTL-compatible control inputs support common digital-control systems. The 400 ohm switch resistance must be included in source-impedance calculations, while low-leakage CMOS characteristics help when handling high-impedance sources. Place the mux close to the acquisition node to minimize sensitivity to capacitive pickup and board contamination.
Industrial Process Monitoring
The MAX338ESE+T can multiplex pressure, temperature, or analog control signals in an industrial monitoring controller. Its ability to operate from a single +4.5 V to +30 V supply is useful for systems with a protected high-voltage input stage, while the ±4.5 V to ±20 V dual-supply option supports bipolar sensor signals. A 3-bit address selects the required process channel and the enable input provides direct routing control. Design the source impedance around the 400 ohm on-state resistance, use a stable analog ground reference, and keep switching traces away from high-energy motor or relay wiring.
Precision Instrumentation
Precision instruments often need to compare or scan several low-level analog sources without duplicating expensive front-end circuitry. The MAX338ESE+T routes one of eight channels to a common output for measurement, allowing the downstream amplifier or converter to be reused. Its low-leakage CMOS construction and 400 ohm on-state resistance suit instrumentation where leakage and source impedance can affect accuracy. For highest precision, use short traces, guard the unused inputs according to the manufacturer guidance, and verify that the selected source's impedance does not create unacceptable attenuation through the switch resistance.
Battery-Powered Measurement
A battery-powered monitor can use the MAX338ESE+T to share one analog input path among several sensors, reducing the need for multiple amplifiers or converters. The multiplexer supports a single +4.5 V to +30 V supply, allowing operation from a protected elevated rail as well as a conventional low-voltage system. Control signals remain TTL-compatible over the specified operating range. The device is a signal-routing element rather than a power converter, so system designers should still budget separate regulation for the analog chain and evaluate signal attenuation produced by the 400 ohm on-state resistance.
Interface Signal Routing
The MAX338ESE+T is useful as a configurable analog interface between a controller and external circuitry. A 3-bit address bus can select the source connected to the common output, while enable provides a direct control path for acquisition timing. Its wide supply capability makes it practical in systems that combine low-voltage logic with higher-voltage analog signals. The signal path should be treated as a high-impedance measurement interface: minimize leakage paths, preserve a continuous ground reference, and avoid routing the common output next to high-current switching nodes to prevent crosstalk and ground disturbance.
داتای سەرچاوەی ئەندازیاری بۆ MAX338ESE+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX338CSE+T | MAX338MSE/PR3+ |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | 8:1 | 8:1 | 8:1 |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| On-State Resistance | 400 ohm | 400 ohm | 400 ohm |
| Single Supply Voltage Range | +4.5 V to +30 V | +4.5 V to +30 V | +4.5 V to +30 V |
| Dual Supply Voltage Range | ±4.5 V to ±20 V | ±4.5 V to ±20 V | ±4.5 V to ±20 V |
| Control Interface | 3-bit binary address with TTL-compatible enable | 3-bit binary address with TTL-compatible enable | 3-bit binary address with TTL-compatible enable |
| Process Technology | 44 V silicon-gate CMOS | 44 V silicon-gate CMOS | 44 V silicon-gate CMOS |
جیاکەرەوە سەرەکییەکان
- Wide single-supply operating range (بەراورد بەMAX338CSE+T)
- Eight-to-one routing in a standard 16-SOIC footprint (بەراورد بەMAX338MSE/PR3+)
- Compatible with single-ended and bipolar supply architectures (بەراورد بەMAX338CSE+T)
تێبینییەکانی دیزاین
Treat the 400 ohm on-state resistance as part of the source impedance seen by the downstream amplifier or converter. For a high-impedance receiver, the selected channel normally presents little loading, but a finite input impedance creates a divider with the switch resistance. Verify the worst-case source impedance, selected channel, and downstream input impedance before setting analog gain. Keep the common-output trace short and place the multiplexer close to the receiver when the routed signal is sensitive to pickup.
Separate the analog routing paths from noisy control and switching signals. Maintain a continuous ground reference beneath or adjacent to the analog traces, avoid running channel lines parallel to high-current power conductors, and minimize exposed trace length. The address and enable inputs should be driven by clean logic signals, while supply decoupling should follow the layout guidance in the MAX338/MAX339 manufacturer datasheet. Review unused-channel handling for the selected operating mode.
Do not treat the MAX338 as a power switch or assume that its supply-voltage rating applies to every signal routed through it. Confirm each channel voltage against the complete absolute maximum and operating specifications. Also distinguish single-supply operation from ±4.5 V to ±20 V dual-supply operation because the allowable common-mode range changes with the supply architecture. Validate address transitions, enable timing, and unused-channel states in the final system.
زانیاری پابەندبوون
Compliance attributes are not stated in the available manufacturer and distributor information. Confirm RoHS, REACH, halogen-free, lead-free, automotive qualification, and conflict-minerals status for the exact order code before production release.