Analog Devices

MAX3485ECSA+ - 12Mbps 3.3V RS-485/RS-422 Transceiver

MPN: MAX3485ECSA+ ✓ چالاک
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

MAX3485ECSA+ گشتی

The Analog Devices MAX3485ECSA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin SOIC package. Its slew-rate-limited driver helps reduce ringing and unwanted reflections on multidrop communication buses.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential physical-layer signals and converts received differential signals back into digital data. Within the product hierarchy, this device is a transceiver, a communications interface IC, and a physical-layer interface component for industrial-control, instrumentation, and embedded data links. The MAX3485ECSA+ supports true differential signaling, making it suitable for noise-resistant communication over longer cable runs than a single-ended interface.

Key features include operation from a 3.3 V supply, data rates up to 12 Mbps, ±15 kV ESD protection on the bus-facing pins, and slew-rate-limited RS-485/RS-422 driver outputs. The integrated half-duplex arrangement allows one driver and one receiver to share a communications pair, while separate driver-enable and receiver-enable inputs provide local control over bus direction and receive state. The 8-SOIC package supports compact surface-mount PCB construction.

The MAX3485 family combines low-power 3.3 V operation with high-speed differential signaling. Slew-rate limiting controls the driver edge rate, helping suppress the high-frequency content that can propagate through cables, connectors, and PCB traces. The protected bus pins add an ESD barrier for ports exposed to industrial wiring, although they do not eliminate the need for correct grounding, cable routing, and external surge protection. The MAX3485E variant is identified by Analog Devices as a production 3.3 V transceiver with enhanced ESD protection.

Typical applications include industrial PLC and factory automation links, RS-485 instrumentation networks, building-control equipment, data-acquisition systems, and embedded controllers requiring a compact, high-speed differential interface. The device can also support point-to-point RS-422 links where the host must control transmit and receive direction independently through its DE and active-low RE inputs.

When laying out a board, place the transceiver close to the connector or transceiver isolation barrier and route the Y and Z bus traces as a tight, balanced pair. Keep the ground reference close to the cable shield connection, avoid long stubs, and follow the interface schematic and termination guidance in the manufacturer datasheet. Component values for termination and biasing should be calculated from the actual cable length, topology, node count, and baud rate.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3485ECSA+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3485ECSA+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, ESD Protection, Maximum Data Rate, Package, Supply Voltage.

Maxim Integrated
Product Type: RS-485/RS-422 transceiver
Package: 8-SOIC, 0.154 inch, 3.90 mm width
بەراوردکردن لەگەڵ MAX3485ECSA+ →
Analog Devices
Product Type: 1/1 RS-422/RS-485 transceiver
ESD Protection: ±15kV
Maximum Data Rate: 12Mbps
بەراوردکردن لەگەڵ MAX3485ECSA+ →
Analog Devices
Product Type: Full-duplex RS-485/RS-422 transceiver
ESD Protection: ±20 kV
Maximum Data Rate: 20 Mbps
بەراوردکردن لەگەڵ MAX3485ECSA+ →
Analog Devices
Product Type: RS-485/RS-422 transceiver
بەراوردکردن لەگەڵ MAX3485ECSA+ →

MAX3485EESA+T

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-SOIC
1/1 RS-422/RS-485 transceiver · 3V to 3.6V · 12Mbps · ±15kV · 1 driver · 1 receiver · RS-422 and RS-485 · Half-duplex

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3485CSA+T

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Analog Devices
📦 8-SOIC
RS-485/RS-422 half-duplex transceiver · 3 V to 3.6 V · 10 Mbps · 1 · 1 · Half-duplex · RS-422 and RS-485 · 8-pin SOIC (NSOIC-8)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3490EESA+

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Analog Devices
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 12 Mbps · ±15 kV · 1 driver · 1 receiver · RS-485 and RS-422 · Slew-rate limited

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3430ESA+

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Related 8-pin SOIC MAX transceiver; maximum data rate, enable behavior, and electrical limits differ and require verification

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3442EASA+T

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Same-brand 8-pin SOIC MAX-family interface; data rate, protection level, and control logic must be confirmed before substitution

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3443EASA+T

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Same-brand 8-pin SOIC MAX-family interface; bus configuration and electrical performance differences require datasheet verification

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3485ECSA+ تایبەتمەندییەکان

Product Type Half-duplex RS-485/RS-422 transceiver
Driver/Receiver Count 1 driver and 1 receiver
ڤۆڵتیەی دابینکردن 3.3 V
Maximum Data Rate 12 Mbps
ESD Protection ±15 kV
Driver Edge Control Slew-rate limited
Supported Standards RS-485 and RS-422
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount
دۆخی RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

ڕێکخستنی پینی MAX3485ECSA+

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 RO — Receiver output
پین 2 RE — Active-low receiver enable
پین 3 DE — Driver enable
پین 4 DI — Driver input
پین 5 GND — Ground
پین 6 Y — Non-inverting driver output and receiver input
پین 7 Z — Inverting driver output and receiver input
پین 8 VCC — Positive supply voltage

بەکارهێنانە باوەکان

MAX3485ECSA+ گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Automation Bus, Point-to-Point RS-422 Data Link, Data-Acquisition Instrumentation, Building Control and HVAC Equipment, Embedded Controller Communication Port, Robotics and Motor-Control Networks.

🏭

Industrial RS-485 Automation Bus

The MAX3485ECSA+ suits industrial automation equipment that communicates over an RS-485 multidrop bus. Its 3.3 V supply operation integrates directly with modern embedded controllers, while the 12 Mbps capability supports high-speed data transfer when cable length and topology permit. The slew-rate-limited driver helps limit high-frequency edge content that can contribute to EMI and reflections on industrial wiring. Place the device near the bus connector, route Y and Z as a balanced pair, and install termination or fail-safe biasing according to the actual network configuration.

🌐

Point-to-Point RS-422 Data Link

The MAX3485ECSA+ can form a point-to-point RS-422 link when the system requires differential signaling over a dedicated cable pair. Its integrated one-driver and one-receiver arrangement simplifies the physical layer, and separate DE and active-low RE controls allow transmit and receive states to be managed independently by the host controller. The 12 Mbps rating provides ample link-rate capability for nearby instruments, although the actual maximum distance depends on cable characteristics, baud rate, termination, grounding, and common-mode conditions.

📟

Data-Acquisition Instrumentation

The MAX3485ECSA+ is appropriate for laboratory and industrial data-acquisition modules that must collect measurements from remote sensors or instrument controllers. Differential RS-485 signaling improves noise immunity compared with a single-ended connection, while the enhanced 3.3 V MAX3485E provides ±15 kV ESD protection on the communications interface. Its 8-pin SOIC package supports compact board construction, and its 12 Mbps maximum rate permits rapid polling when each sensor’s distance and termination permit the higher communication speed.

🏠

Building Control and HVAC Equipment

The MAX3485ECSA+ fits building-control units, HVAC controllers, and room equipment that use RS-485 or RS-422 supervisory networks. The 3.3 V interface is well matched to low-voltage embedded processors, and the slew-rate-limited driver helps control edge-generated interference in compact control cabinets. Use the transceiver near the field-wiring connector, maintain a nearby ground reference, and apply bus termination and biasing according to the number of nodes and cable length. The ±15 kV-enhanced interface adds useful electrostatic-discharge protection for connected equipment.

🧩

Embedded Controller Communication Port

The MAX3485ECSA+ can add a robust differential communications port to an embedded controller, sensor gateway, or remote terminal. Its one-driver and one-receiver configuration reduces the number of external interface components, while the 8-pin SOIC footprint simplifies routing on compact boards. At 3.3 V, the device integrates naturally with low-voltage digital systems. The host controller should manage DE and active-low RE in a defined sequence to prevent unwanted bus contention and should observe the datasheet timing limits during transmit-to-receive turnaround.

🤖

Robotics and Motor-Control Networks

The MAX3485ECSA+ can support command, status, and diagnostic communication between robotic controllers, motor controllers, and remote equipment. Differential signaling is valuable in environments containing motor drives, switching power converters, and mechanically generated noise. The transceiver’s 3.3 V supply, 12 Mbps capability, and slew-rate-limited outputs support a compact high-speed interface, provided the wiring, grounding, and termination are engineered for the installation. Keep the bus transceiver close to the connector and maintain short ground paths to reduce susceptibility to common-mode noise.

کورتەی بەرهەمە پێشنیارکراوەکان

MAX211IDBR Texas Instruments بەکارهێنراوە لە: Industrial RS-485 Automation Bus ISO1042BDWR Texas Instruments بەکارهێنراوە لە: Industrial RS-485 Automation Bus, Embedded Controller Communication Port ADM485JNZ Analog Devices بەکارهێنراوە لە: Industrial RS-485 Automation Bus, Robotics and Motor-Control Networks MAX3232IPW Texas Instruments بەکارهێنراوە لە: Point-to-Point RS-422 Data Link, Building Control and HVAC Equipment ISO122JUE4 Texas Instruments بەکارهێنراوە لە: Point-to-Point RS-422 Data Link MAX3490EESA+ Analog Devices بەکارهێنراوە لە: Point-to-Point RS-422 Data Link ADS1254E Texas Instruments بەکارهێنراوە لە: Data-Acquisition Instrumentation ADS1252U Texas Instruments بەکارهێنراوە لە: Data-Acquisition Instrumentation MAX138EPL+ Analog Devices بەکارهێنراوە لە: Data-Acquisition Instrumentation SP485EMN-L/TR MaxLinear بەکارهێنراوە لە: Building Control and HVAC Equipment TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Building Control and HVAC Equipment STM32F103ZGT6J STMicroelectronics بەکارهێنراوە لە: Embedded Controller Communication Port STM32L051K6T6 STMicroelectronics بەکارهێنراوە لە: Embedded Controller Communication Port STPA003HSD-48X STMicroelectronics بەکارهێنراوە لە: Robotics and Motor-Control Networks STPA003CD-48X STMicroelectronics بەکارهێنراوە لە: Robotics and Motor-Control Networks
What are the key specifications of MAX3485ECSA+ that engineers should know?
The MAX3485ECSA+ is a 3.3 V, 12 Mbps half-duplex transceiver with one driver, one receiver, ±15 kV ESD protection, and an 8-pin SOIC package. According to the Analog Devices MAX3485E product page, the device is a production 3.3 V-powered, slew-rate-limited true RS-485/RS-422 transceiver. Its separate DE and active-low RE controls allow the host to select transmit or receive operation, making the device suitable for industrial buses, point-to-point RS-422 links, and embedded data-acquisition equipment.
Where can I download the MAX3485ECSA+ datasheet PDF?
The MAX3485ECSA+ datasheet and product documentation are available through the Analog Devices MAX3485E product page at analog.com. The manufacturer page identifies the MAX3485E as a production 3.3 V-powered, ±15 kV ESD-protected, 12 Mbps slew-rate-limited true RS-485/RS-422 transceiver. Use the manufacturer datasheet for the complete pin-description table, electrical characteristics, timing diagrams, truth table, and recommended application circuit.
Where can I find the MAX3485ECSA+ pinout?
The MAX3485ECSA+ uses an 8-pin SOIC footprint, and its pin assignments are shown in the pin-description table of the manufacturer MAX3485E datasheet. The interface includes supply, ground, driver input, receiver output, driver enable, receiver enable, and the two differential bus conductors. Assign PCB tracks from the datasheet pin-description table rather than relying on package orientation alone, and verify the exposed interface functions against the selected board revision.
Is the MAX3485ECSA+ suitable for 12 Mbps RS-485 communication?
Yes, the MAX3485ECSA+ is rated by Analog Devices for data rates up to 12 Mbps and is identified as a slew-rate-limited true RS-485/RS-422 transceiver. Its 3.3 V supply operation supports modern embedded systems, while the driver edge-rate limitation helps reduce ringing and high-frequency content. Actual link margin still depends on cable length, topology, termination, stub length, grounding, and transceiver placement.
What does the E in MAX3485E provide?
The MAX3485E is the enhanced-ESD version of the MAX3485 family. Analog Devices describes the MAX3485E as a 3.3 V-powered, ±15 kV ESD-protected, 12 Mbps slew-rate-limited true RS-485/RS-422 transceiver. The MAX3485ECSA+ ordering code therefore identifies the enhanced device in an 8-pin SOIC package. ESD protection helps reduce damage from electrostatic discharge on the interface pins, but external surge-protection design may still be required.
How do DE and active-low RE control the MAX3485ECSA+?
The DE input controls the differential driver, while the active-low receiver-enable input controls the receiver output. Driving DE high enables transmission, and holding active-low RE low disables the receiver for applications that want a high-impedance receive state. According to the MAX3485 family description, each device contains one driver and one receiver. Use the manufacturer truth table to define startup, turnaround, and bus-direction sequencing.
Is MAX3485EESA+T a drop-in replacement for MAX3485ECSA+?
The MAX3485EESA+T is a closely related MAX3485E-family device offered in an 8-pin SOIC package, making it the strongest same-brand replacement candidate. The comparison data identifies both parts as 3.3 V-powered, ±15 kV ESD-protected RS-485/RS-422 transceivers. Before substitution, verify the exact temperature grade, pin assignments, electrical limits, and lifecycle status in the manufacturer documentation for the specific ordering code.
Can MAX3430ESA+ replace MAX3485ECSA+ on the same PCB?
MAX3430ESA+ can be evaluated as a same-brand MAX-family replacement in the 8-pin SOIC format, but it should not be treated as automatically identical to MAX3485ECSA+. The cross-reference comparison highlights differences between the two devices in addition to their similarities. Confirm pin functions, maximum data rate, supply range, ESD rating, receiver behavior, and temperature grade against the manufacturer datasheets before approving a substitution.
What is the best cross-brand equivalent for MAX3485ECSA+?
No cross-brand equivalent can be identified conclusively from the available cross-reference information. The records provide a generic cross-reference search rather than a verified list of competitor MPNs with matching 8-pin SOIC footprints, 3.3 V operation, 12 Mbps capability, and ±15 kV ESD protection. Select a candidate only after comparing its official pinout and electrical characteristics, then request a quote through the Request a Quote form on this page.
When should I choose MAX3485ECSA+ over MAX3490EESA+?
Choose MAX3485ECSA+ when the design specifically requires the MAX3485E interface in an 8-pin SOIC package, including its 12 Mbps rating and ±15 kV ESD protection. MAX3490EESA+ belongs to the related MAX3490 family and may offer different bus or protection characteristics, so it should be selected only after confirming the required data rate, topology, protection level, and exact pin configuration. Both are same-brand candidates, but device-level specifications determine the correct choice.
What is the MAX3485ECSA+ used for in industrial automation?
The MAX3485ECSA+ is used as the physical-layer interface between an embedded controller and an RS-485 or RS-422 industrial bus. Its one-driver, one-receiver arrangement supports half-duplex multidrop communication, while 12 Mbps capability supports demanding links when the physical installation permits. The Analog Devices MAX3485 family description specifically identifies RS-485/RS-422 transceiver applications, and slew-rate-limited outputs help control edge-induced EMI.
Does the MAX3485ECSA+ require external termination?
The MAX3485ECSA+ may require external termination resistors depending on the bus topology and transmission rate. Termination is generally placed at the physical ends of a multidrop RS-485 cable, while biasing resistors establish the fail-safe idle state in a multidrop network. The correct values depend on cable length, node count, baud rate, and driver topology, so use the manufacturer application guidance and calculate the network rather than fitting a universal resistor value.
How should I lay out an RS-485 board using MAX3485ECSA+?
Place the MAX3485ECSA+ near the bus connector or transceiver isolation barrier, and route Y and Z as a short, balanced differential pair on the PCB. Keep the ground reference and cable-shield connection close to the connector, avoid long stubs, and keep sensitive analog or high-speed digital traces away from the interface. The MAX3485ECSA+ is a surface-mount 8-pin SOIC, allowing the bus circuitry to remain close to the connector without a through-hole footprint.
Is MAX3485ECSA+ suitable for RS-422 point-to-point links?
Yes, the MAX3485ECSA+ supports true RS-422 as well as RS-485 operation according to the Analog Devices product description. Its one-driver and one-receiver arrangement can form a point-to-point differential link, with DE controlling the transmitter and active-low RE controlling the receiver. For a reliable implementation, follow the datasheet logic levels and confirm the common-mode range, termination method, cable length, and ground-reference strategy.
Where can I buy MAX3485ECSA+ and what is its current lead time?
Use the Request a Quote form on this page to request MAX3485ECSA+ availability, current lead time, and the exact quantity required. The product is shown as a production MAX3485E-family device by Analog Devices, but current inventory and delivery scheduling can vary by ordering code and order volume. Provide the package suffix and required quantity in the request so the quote can be matched to the intended 8-pin SOIC device.

داتای سەرچاوەی ئەندازیاری بۆ MAX3485ECSA+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX3485ECSA+ for a compact 3.3 V RS-485 or RS-422 interface that requires a maximum data rate of 12 Mbps, slew-rate-limited differential signaling, and ±15 kV ESD protection in an 8-pin SOIC package. MAX3485EESA+T is the closest same-family option to evaluate first because it shares the MAX3485E identity and package format; verify its exact temperature grade and qualification before release. MAX3485CSA+T may suit designs that do not require the enhanced E-device ESD rating, while MAX3490EESA+, MAX3430ESA+, MAX3442EASA+T, and MAX3443EASA+T should be selected only after their official data rates, protection ratings, bus features, and control logic match the target system. If the design requires galvanic isolation, long cable runs, severe surge exposure, or a bus topology outside the transceiver’s specified limits, select an isolated or externally protected interface solution instead of relying on the MAX3485ECSA+ alone.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3485EESA+T MAX3485CSA+T MAX3490EESA+ MAX3430ESA+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC

جیاکەرەوە سەرەکییەکان

  • Enhanced 12 Mbps communications interface (بەراورد بەMAX3430ESA+)
  • Enhanced electrostatic-discharge protection (بەراورد بەMAX3485CSA+T)
  • Directly related E-family ordering option (بەراورد بەMAX3485EESA+T)

تێبینییەکانی دیزاین

Place the MAX3485ECSA+ close to the field-wiring connector or isolation barrier, and route Y and Z together as a short differential pair. Keep the interface ground reference near the cable-shield connection, avoid long PCB stubs, and place protection components directly at the connector entry. This arrangement reduces the length of high-frequency transient paths and helps prevent external events from propagating deeper into the equipment.

Treat Y and Z as one controlled impedance pair rather than as independent nets. Match their routing width and spacing, keep both traces over a continuous reference plane, and avoid crossings or splits that create impedance discontinuities. Confirm edge-rate and attenuation requirements against the selected cable. Although the MAX3485ECSA+ uses a slew-rate-limited driver, PCB loss and connector capacitance can still degrade a 12 Mbps signal when long or loosely constructed cables are used.

Do not enable the driver and receiver incorrectly during bus turnaround. Define DE and active-low RE states in firmware, observe the manufacturer timing limits, and avoid leaving multiple nodes driving the bus simultaneously. Also do not assume ±15 kV ESD protection replaces a coordinated surge-protection network; external lightning, switching, and industrial transients can exceed the transceiver's protected levels.

Provide a stable 3.3 V rail and route its return current directly to the transceiver ground reference. Place local high-frequency bypass capacitance at the device power pins according to the manufacturer application circuit, using a short ground path. Keep the supply plane and ground reference continuous under the interface so that driver and receiver currents do not inject large disturbances into the logic ground used by the host controller.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The available manufacturer and distributor records identify the MAX3485E as a production 3.3 V RS-485/RS-422 transceiver, but they do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for this ordering code. Confirm each status with Analog Devices before regulatory submission.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3485ECSA+ datasheet MAX3485ECSA+ pinout MAX3485ECSA+ datasheet pdf MAX3485ECSA+ equivalent MAX3485ECSA+ replacement MAX3485ECSA+ drop-in replacement MAX3485ECSA+ vs MAX3485EESA+T MAX3485ECSA+ vs MAX3430ESA+ MAX3485ECSA+ footprint MAX3485ECSA+ price MAX3485ECSA+ stock Analog Devices MAX3485ECSA+ MAX3485 12Mbps RS-485 transceiver MAX3485ECSA+ industrial RS-485 MAX3485ECSA+ 8-SOIC pinout

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices Maxim Integrated MAX3485ECSA+ MAX3485EESA+T MAX3485CSA+T MAX3490EESA+ MAX3430ESA+ MAX3442EASA+T MAX3443EASA+T RS-485 RS-422 half-duplex transceiver differential communications interface interface IC physical-layer IC semiconductor 3.3 V power supply 12 Mbps data rate ±15 kV ESD protection slew-rate-limited driver 8-pin SOIC SOIC package family surface-mount package industrial automation data-acquisition instrumentation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ