MC908JW16FAE - 8-bit HC08 MCU with USB, 16KB Flash | NXP
MPN: MC908JW16FAE ✗ کۆتایی ژیانMC908JW16FAE گشتی
Background knowledge: An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for embedded control tasks such as human-interface devices, sensor reading, and low-rate communication. The MC908JW16 belongs to the Freescale/NXP HC08 family, which sits in the product-type hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. HC08 devices use a von Neumann architecture with on-chip flash and RAM, and the JW sub-family adds a USB 1.1 device controller plus a 12-channel, 10-bit ADC.
Key features include 16 KB of flash program memory with in-application programming support, a USB 1.1 full-speed (12 Mbps) device transceiver that meets USB 2.0 full-speed electrical specifications, and a 12-channel 10-bit analog-to-digital converter. Additional peripherals are a 2-channel timer interface (TPM), a serial communications interface (SCI), a serial peripheral interface (SPI), and an 8-bit keyboard interrupt module.
The architecture pairs the HC08 CPU with an on-chip voltage regulator, brownout reset, low-voltage reset, and a clock generator module supporting an external crystal or internal trimmable reference. The integrated USB pull-up on the D+ line and the USB transceiver allow direct connection to a Type-B or Mini-B connector, eliminating external PHY circuitry.
Typical applications include USB keyboards, USB mice, USB gamepads, USB barcode scanners, USB custom HID peripherals, low-cost USB-to-UART bridges, and embedded consumer devices that require a single-chip USB interface.
When designing with this part, observe USB signal-integrity guidelines and keep the D+/D- traces short, length-matched, and routed over a continuous ground plane; the integrated transceiver is sufficient for typical peripheral cables up to 3 m.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
جێگرەوەکانی جێگۆڕکێ بۆ MC908JW16FAE — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MC908JW16FAE (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Maximum Clock Frequency, Operating Supply Voltage, Operating Temperature, Package, Program Memory Size.
MC908JW32FAE
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MC908JB16FAE
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MC908JW16FAE زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Core | HC08 |
| پانی بسێ داتا | 8 bit |
| Program Memory Size | 16 KB flash |
| RAM Size | 1.4 KB |
| زۆرترین فرێکوێنسیی کاتژمێر | 8 MHz internal bus |
| ڤۆڵتاژی دابینکردنی کارکردن | 2.7 V to 3.6 V |
| ADC | 12-channel, 10-bit |
| USB Interface | USB 1.1 full-speed device (12 Mbps) |
| Timers | 2-channel TPM |
| Communication Interfaces | SCI, SPI |
| پاکێج | 48-pin LQFP |
| جۆری دامەزراندن | Surface Mount |
| پلەی گەرمیی کارکردن | 0C to +70C |
| دۆخی RoHS | Compliant |
ڕێکخستنی پینی MC908JW16FAE
| پین 1 | PTA0 — Port A bit 0 / ADC channel 0 |
| پین 2 | PTA1 — Port A bit 1 / ADC channel 1 |
| پین 3 | PTA2 — Port A bit 2 / ADC channel 2 |
| پین 4 | PTA3 — Port A bit 3 / ADC channel 3 |
| پین 5 | VSS — Ground |
| پین 6 | VDD — Power supply 2.7-3.6 V |
| پین 7 | PTA4 — Port A bit 4 / ADC channel 4 |
| پین 8 | PTA5 — Port A bit 5 / ADC channel 5 |
| پین 9 | PTA6 — Port A bit 6 / ADC channel 6 |
| پین 10 | PTA7 — Port A bit 7 / ADC channel 7 |
| پین 11 | PTB0 — Port B bit 0 / ADC channel 8 |
| پین 12 | PTB1 — Port B bit 1 / ADC channel 9 |
| پین 13 | PTB2 — Port B bit 2 / ADC channel 10 |
| پین 14 | PTB3 — Port B bit 3 / ADC channel 11 |
| پین 15 | PTB4 — Port B bit 4 |
| پین 16 | PTB5 — Port B bit 5 |
| پین 17 | PTB7 — Port B bit 7 |
| پین 18 | PTC0 — Port C bit 0 |
| پین 19 | PTC1 — Port C bit 1 |
| پین 20 | PTC2 — Port C bit 2 |
| پین 21 | PTC3 — Port C bit 3 |
| پین 22 | PTC4 — Port C bit 4 |
| پین 23 | PTC5 — Port C bit 5 |
| پین 24 | PTC6 — Port C bit 6 |
| پین 25 | PTC7 — Port C bit 7 |
| پین 26 | PTD0 — Port D bit 0 / SPI MISO |
| پین 27 | PTD1 — Port D bit 1 / SPI MOSI |
| پین 28 | PTD2 — Port D bit 2 / SPI SCK |
| پین 29 | PTD3 — Port D bit 3 / SPI SS |
| پین 30 | PTD4 — Port D bit 4 / SCI TxD |
| پین 31 | PTD5 — Port D bit 5 / SCI RxD |
| پین 32 | PTD6 — Port D bit 6 |
| پین 33 | PTD7 — Port D bit 7 |
| پین 34 | USB D- — USB data minus |
| پین 35 | USB D+ — USB data plus |
| پین 36 | VBUS — USB VBUS sense |
| پین 37 | VREG — Voltage regulator output |
| پین 38 | VSS — Ground |
| پین 39 | VDD — Power supply 2.7-3.6 V |
| پین 40 | OSC1 — Crystal oscillator input |
| پین 41 | OSC2 — Crystal oscillator output |
| پین 42 | RST — Reset (active low) |
| پین 43 | IRQ — External interrupt |
| پین 44 | TCLK — Timer clock input |
| پین 45 | PTE0 — Port E bit 0 |
| پین 46 | PTE1 — Port E bit 1 |
| پین 47 | PTE2 — Port E bit 2 |
| پین 48 | PTE3 — Port E bit 3 |
بەکارهێنانە باوەکان
MC908JW16FAE گونجاوە بۆ 6 بەکارھێنانs: USB HID Keyboard, USB Mouse / Pointer, USB Barcode Scanner, USB Gamepad / Joystick, USB Custom HID Peripheral, Low-Cost USB-to-UART Bridge.
USB HID Keyboard
The MC908JW16FAE is purpose-built for USB keyboard applications. The integrated USB 1.1 full-speed device controller with on-chip 1.5 kohm pull-up eliminates the external PHY, while the 16 KB flash holds the HID boot protocol descriptor plus key debounce firmware; 1.4 KB RAM is sufficient for the keyboard matrix scan buffer. The 12-channel ADC can be repurposed for backlight or capacitive sense inputs, reducing external circuitry. With the SCI available, designers can add a factory test/debug UART without extra pins.
پێشنیارکراو
USB Mouse / Pointer
For USB mouse and pointer designs, the MC908JW16FAE integrates the USB device controller, an SPI port for an optical sensor interface (e.g., ADNS-3080 or PMW3360), and enough flash/RAM for HID mouse descriptors and motion interpolation. The 8-bit HC08 core executes pointer-fusion algorithms within the 1 ms USB poll interval without offloading to a co-processor. The 12-channel ADC supports side-button analog inputs and battery monitoring on wireless variants.
پێشنیارکراو
USB Barcode Scanner
The MC908JW16FAE is well suited to handheld USB barcode scanners. The HC08 core decodes 1D barcodes from a CMOS sensor over SPI, while the integrated USB 1.1 device controller presents a HID Keyboard or CDC interface to the host. The 16 KB flash holds symbology tables and decoder firmware; 1.4 KB RAM stores the scan buffer. Low STOP-mode current extends battery life on wireless scanner sleds.
پێشنیارکراو
USB Gamepad / Joystick
USB gamepads and joysticks leverage the MC908JW16FAE's ADC for analog stick inputs (typically two 10-bit axes) and GPIO for digital buttons. The USB HID device controller enumerates as a gamepad without custom drivers on Windows, Linux, and macOS. The TPM module generates precise PWM rumble/feedback signals if needed; 16 KB flash holds multiple HID report templates.
پێشنیارکراو
USB Custom HID Peripheral
For proprietary USB HID peripherals such as presentation clickers, custom test instruments, or industrial pendants, the MC908JW16FAE provides flexible GPIOs, an SPI for external peripherals, and the SCI for factory programming. The integrated USB 1.1 device controller handles enumeration; 16 KB flash stores vendor-specific HID reports. The 2.7-3.6 V supply aligns with single-cell Li-ion battery operation.
پێشنیارکراو
Low-Cost USB-to-UART Bridge
Using the integrated USB 1.1 device controller and the on-chip SCI, the MC908JW16FAE can implement a low-cost USB-to-UART bridge (CDC ACM class). It replaces commercial bridges (CP2104) at lower BOM cost on embedded debug or service ports. The 16 KB flash holds the CDC ACM descriptor and bridge firmware; 1.4 KB RAM buffers 64-byte CDC packets at full-speed USB rates.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MC908JW16FAE — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MC908JW32FAE | MC908JB16FAE |
|---|---|---|---|
| Package | 48-pin LQFP | 48-pin LQFP - same | 48-pin LQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | HC08 8-bit | HC08 8-bit | HC08 8-bit |
| Flash | 16 KB | 32 KB | 16 KB |
| USB | USB 1.1 FS device + internal pull-up | USB 1.1 FS device + internal pull-up | USB 1.1 device, no internal pull-up |
| Operating Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
| Lifecycle | NRND | NRND | Obsolete |
جیاکەرەوە سەرەکییەکان
- Integrated USB 1.1 device controller with internal pull-up (بەراورد بەMC908JB16FAE)
- Doubled flash at identical pinout (بەراورد بەMC908JW16FAE -> MC908JW32FAE upgrade)
تێبینییەکانی دیزاین
Estimated: Keep the USB D+ and D- traces short (<25 mm), length-matched within 2 mm, and routed over a continuous ground plane to maintain 90 ohm differential impedance. Place the 27 ohm series resistors on D+/D- close to the MCU pins. Add a USBLC6-2SC6 TVS array near the USB connector for ESD protection; the internal transceiver has no ESD rating.
Decouple each VDD pin with a 100 nF ceramic capacitor (X7R, 0402) placed within 5 mm. Add a single 4.7 uF bulk capacitor near the VREG pin. The on-chip voltage regulator requires a 1 uF external capacitor on VREG for stability; do not omit this component or the core will reset unpredictably under USB load steps.
Do not connect the internal USB pull-up manually; the JW16 auto-connects D+ pull-up when the USB module is enabled. Forcing an external pull-up to 3.3 V violates the USB spec. When programming flash in-application, ensure the USB module is disabled during the erase/program sequence or the watchdog will reset the part.
زانیاری پابەندبوون
RoHS compliant per LCSC and Rochester Electronics listings. Not AEC-Q100 qualified; consumer-grade part. NRND status confirmed via NXP product lifecycle; last-time-buy recommended for new production.