MC908JW16FAE - 8-bit HC08 MCU with USB, 16KB Flash | NXP
MPN: MC908JW16FAE ✗ پایان تولیدMC908JW16FAE نمای کلی
Background knowledge: An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for embedded control tasks such as human-interface devices, sensor reading, and low-rate communication. The MC908JW16 belongs to the Freescale/NXP HC08 family, which sits in the product-type hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. HC08 devices use a von Neumann architecture with on-chip flash and RAM, and the JW sub-family adds a USB 1.1 device controller plus a 12-channel, 10-bit ADC.
Key features include 16 KB of flash program memory with in-application programming support, a USB 1.1 full-speed (12 Mbps) device transceiver that meets USB 2.0 full-speed electrical specifications, and a 12-channel 10-bit analog-to-digital converter. Additional peripherals are a 2-channel timer interface (TPM), a serial communications interface (SCI), a serial peripheral interface (SPI), and an 8-bit keyboard interrupt module.
The architecture pairs the HC08 CPU with an on-chip voltage regulator, brownout reset, low-voltage reset, and a clock generator module supporting an external crystal or internal trimmable reference. The integrated USB pull-up on the D+ line and the USB transceiver allow direct connection to a Type-B or Mini-B connector, eliminating external PHY circuitry.
Typical applications include USB keyboards, USB mice, USB gamepads, USB barcode scanners, USB custom HID peripherals, low-cost USB-to-UART bridges, and embedded consumer devices that require a single-chip USB interface.
When designing with this part, observe USB signal-integrity guidelines and keep the D+/D- traces short, length-matched, and routed over a continuous ground plane; the integrated transceiver is sufficient for typical peripheral cables up to 3 m.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
جایگزین‌های drop-in برای MC908JW16FAE — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای MC908JW16FAE (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Maximum Clock Frequency, Operating Supply Voltage, Operating Temperature, Package, Program Memory Size.
MC908JW32FAE
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MC908JB16FAE
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MC908JW16FAE حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core | HC08 |
| عرض گذرگاه داده | 8 bit |
| Program Memory Size | 16 KB flash |
| RAM Size | 1.4 KB |
| حداکثر فرکانس کلاک | 8 MHz internal bus |
| ولتاژ تغذیه کاری | 2.7 V to 3.6 V |
| ADC | 12-channel, 10-bit |
| USB Interface | USB 1.1 full-speed device (12 Mbps) |
| Timers | 2-channel TPM |
| Communication Interfaces | SCI, SPI |
| بسته‌بندی | 48-pin LQFP |
| نوع نصب | Surface Mount |
| دمای کاری | 0C to +70C |
| وضعیت RoHS | Compliant |
پیکربندی پین MC908JW16FAE
| پین 1 | PTA0 — Port A bit 0 / ADC channel 0 |
| پین 2 | PTA1 — Port A bit 1 / ADC channel 1 |
| پین 3 | PTA2 — Port A bit 2 / ADC channel 2 |
| پین 4 | PTA3 — Port A bit 3 / ADC channel 3 |
| پین 5 | VSS — Ground |
| پین 6 | VDD — Power supply 2.7-3.6 V |
| پین 7 | PTA4 — Port A bit 4 / ADC channel 4 |
| پین 8 | PTA5 — Port A bit 5 / ADC channel 5 |
| پین 9 | PTA6 — Port A bit 6 / ADC channel 6 |
| پین 10 | PTA7 — Port A bit 7 / ADC channel 7 |
| پین 11 | PTB0 — Port B bit 0 / ADC channel 8 |
| پین 12 | PTB1 — Port B bit 1 / ADC channel 9 |
| پین 13 | PTB2 — Port B bit 2 / ADC channel 10 |
| پین 14 | PTB3 — Port B bit 3 / ADC channel 11 |
| پین 15 | PTB4 — Port B bit 4 |
| پین 16 | PTB5 — Port B bit 5 |
| پین 17 | PTB7 — Port B bit 7 |
| پین 18 | PTC0 — Port C bit 0 |
| پین 19 | PTC1 — Port C bit 1 |
| پین 20 | PTC2 — Port C bit 2 |
| پین 21 | PTC3 — Port C bit 3 |
| پین 22 | PTC4 — Port C bit 4 |
| پین 23 | PTC5 — Port C bit 5 |
| پین 24 | PTC6 — Port C bit 6 |
| پین 25 | PTC7 — Port C bit 7 |
| پین 26 | PTD0 — Port D bit 0 / SPI MISO |
| پین 27 | PTD1 — Port D bit 1 / SPI MOSI |
| پین 28 | PTD2 — Port D bit 2 / SPI SCK |
| پین 29 | PTD3 — Port D bit 3 / SPI SS |
| پین 30 | PTD4 — Port D bit 4 / SCI TxD |
| پین 31 | PTD5 — Port D bit 5 / SCI RxD |
| پین 32 | PTD6 — Port D bit 6 |
| پین 33 | PTD7 — Port D bit 7 |
| پین 34 | USB D- — USB data minus |
| پین 35 | USB D+ — USB data plus |
| پین 36 | VBUS — USB VBUS sense |
| پین 37 | VREG — Voltage regulator output |
| پین 38 | VSS — Ground |
| پین 39 | VDD — Power supply 2.7-3.6 V |
| پین 40 | OSC1 — Crystal oscillator input |
| پین 41 | OSC2 — Crystal oscillator output |
| پین 42 | RST — Reset (active low) |
| پین 43 | IRQ — External interrupt |
| پین 44 | TCLK — Timer clock input |
| پین 45 | PTE0 — Port E bit 0 |
| پین 46 | PTE1 — Port E bit 1 |
| پین 47 | PTE2 — Port E bit 2 |
| پین 48 | PTE3 — Port E bit 3 |
کاربردهای معمول
MC908JW16FAE مناسب است برای 6 کاربردs: USB HID Keyboard, USB Mouse / Pointer, USB Barcode Scanner, USB Gamepad / Joystick, USB Custom HID Peripheral, Low-Cost USB-to-UART Bridge.
USB HID Keyboard
The MC908JW16FAE is purpose-built for USB keyboard applications. The integrated USB 1.1 full-speed device controller with on-chip 1.5 kohm pull-up eliminates the external PHY, while the 16 KB flash holds the HID boot protocol descriptor plus key debounce firmware; 1.4 KB RAM is sufficient for the keyboard matrix scan buffer. The 12-channel ADC can be repurposed for backlight or capacitive sense inputs, reducing external circuitry. With the SCI available, designers can add a factory test/debug UART without extra pins.
پیشنهادی
USB Mouse / Pointer
For USB mouse and pointer designs, the MC908JW16FAE integrates the USB device controller, an SPI port for an optical sensor interface (e.g., ADNS-3080 or PMW3360), and enough flash/RAM for HID mouse descriptors and motion interpolation. The 8-bit HC08 core executes pointer-fusion algorithms within the 1 ms USB poll interval without offloading to a co-processor. The 12-channel ADC supports side-button analog inputs and battery monitoring on wireless variants.
پیشنهادی
USB Barcode Scanner
The MC908JW16FAE is well suited to handheld USB barcode scanners. The HC08 core decodes 1D barcodes from a CMOS sensor over SPI, while the integrated USB 1.1 device controller presents a HID Keyboard or CDC interface to the host. The 16 KB flash holds symbology tables and decoder firmware; 1.4 KB RAM stores the scan buffer. Low STOP-mode current extends battery life on wireless scanner sleds.
پیشنهادی
USB Gamepad / Joystick
USB gamepads and joysticks leverage the MC908JW16FAE's ADC for analog stick inputs (typically two 10-bit axes) and GPIO for digital buttons. The USB HID device controller enumerates as a gamepad without custom drivers on Windows, Linux, and macOS. The TPM module generates precise PWM rumble/feedback signals if needed; 16 KB flash holds multiple HID report templates.
پیشنهادی
USB Custom HID Peripheral
For proprietary USB HID peripherals such as presentation clickers, custom test instruments, or industrial pendants, the MC908JW16FAE provides flexible GPIOs, an SPI for external peripherals, and the SCI for factory programming. The integrated USB 1.1 device controller handles enumeration; 16 KB flash stores vendor-specific HID reports. The 2.7-3.6 V supply aligns with single-cell Li-ion battery operation.
پیشنهادی
Low-Cost USB-to-UART Bridge
Using the integrated USB 1.1 device controller and the on-chip SCI, the MC908JW16FAE can implement a low-cost USB-to-UART bridge (CDC ACM class). It replaces commercial bridges (CP2104) at lower BOM cost on embedded debug or service ports. The 16 KB flash holds the CDC ACM descriptor and bridge firmware; 1.4 KB RAM buffers 64-byte CDC packets at full-speed USB rates.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای MC908JW16FAE — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MC908JW32FAE | MC908JB16FAE |
|---|---|---|---|
| Package | 48-pin LQFP | 48-pin LQFP - same | 48-pin LQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | HC08 8-bit | HC08 8-bit | HC08 8-bit |
| Flash | 16 KB | 32 KB | 16 KB |
| USB | USB 1.1 FS device + internal pull-up | USB 1.1 FS device + internal pull-up | USB 1.1 device, no internal pull-up |
| Operating Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
| Lifecycle | NRND | NRND | Obsolete |
تفاوت‌های کلیدی
- Integrated USB 1.1 device controller with internal pull-up (در مقابلMC908JB16FAE)
- Doubled flash at identical pinout (در مقابلMC908JW16FAE -> MC908JW32FAE upgrade)
یادداشت‌های طراحی
Estimated: Keep the USB D+ and D- traces short (<25 mm), length-matched within 2 mm, and routed over a continuous ground plane to maintain 90 ohm differential impedance. Place the 27 ohm series resistors on D+/D- close to the MCU pins. Add a USBLC6-2SC6 TVS array near the USB connector for ESD protection; the internal transceiver has no ESD rating.
Decouple each VDD pin with a 100 nF ceramic capacitor (X7R, 0402) placed within 5 mm. Add a single 4.7 uF bulk capacitor near the VREG pin. The on-chip voltage regulator requires a 1 uF external capacitor on VREG for stability; do not omit this component or the core will reset unpredictably under USB load steps.
Do not connect the internal USB pull-up manually; the JW16 auto-connects D+ pull-up when the USB module is enabled. Forcing an external pull-up to 3.3 V violates the USB spec. When programming flash in-application, ensure the USB module is disabled during the erase/program sequence or the watchdog will reset the part.
اطلاعات انطباق
RoHS compliant per LCSC and Rochester Electronics listings. Not AEC-Q100 qualified; consumer-grade part. NRND status confirmed via NXP product lifecycle; last-time-buy recommended for new production.