MCP3202-CI/SN - 12-Bit Dual-Channel SPI ADC | Microchip
MPN: MCP3202-CI/SN ✓ چالاکMCP3202-CI/SN گشتی
An ADC is a semiconductor that converts an analog voltage into a digital value for processing by a microcontroller or another digital system. The MCP3202 belongs to the SAR ADC hierarchy: successive approximation register architecture compares the input voltage with an internal reference through a sequence of conversion steps, producing a 12-bit result. Its dual input arrangement supports two measurement channels while sharing one SPI interface and a common voltage reference.
Key operating features include a 12-bit resolution, two analog input channels, a 2.7 V to 5.5 V operating-voltage range, and an SPI-compatible serial interface. The MCP3202 supports both single-ended and differential input configurations according to the device data sheet. A 5 V supply permits the maximum 100 ksps conversion rate, while operation at 2.7 V provides a maximum rate of 50 ksps. The interface uses serial clock, data input, data output, and chip-select signals, reducing the number of parallel signal paths required on small embedded boards.
Typical uses include battery-powered environmental sensors, industrial process monitoring, temperature measurement bridges, laboratory data acquisition, and educational microcontroller platforms such as Arduino and Raspberry Pi. In these systems, the ADC can be connected to a host controller through SPI while an external reference establishes the measurement scale. The low active current is useful for portable equipment, although the actual system consumption depends on the host controller, reference circuit, sensor, and digital interface activity.
Designers should pay attention to analog grounding, reference stability, input range, sampling timing, and the relationship between supply voltage and maximum conversion rate. The analog input voltage must remain within the input range allowed by the selected reference configuration, and the reference pins should be decoupled according to the recommended application circuit. Keep SPI traces short, provide a clean return path for the digital signals, and place input and bypass capacitors close to the appropriate device pins. The 8-pin SOIC footprint is also convenient for mixed-signal designs where the ADC must share a board with a microcontroller and regulated supply rails.
جێگرەوەکانی جێگۆڕکێ بۆ MCP3202-CI/SN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP3202-CI/SN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Resolution, Architecture, Number of Analog Input Channels, Input Configuration.
MCP3202-CI/SNVAO
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MCP3202T-CI/SNVAO
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MCP3202T-BI/SN
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MCP3202-CI/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP3201-BI/SN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP3202-CI/SN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| وردی | 12 bit |
| Number of Input Channels | 2 analog input channels |
| ADC Architecture | Successive approximation register (SAR) |
| Conversion Rate at 5 V | 100 ksps |
| Conversion Rate at 2.7 V | 50 ksps |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Typical Standby Current | 500 nA |
| Typical Active Current | 375 uA |
| ڕووکار | SPI-compatible serial interface |
| Input Configuration | Single-ended or differential, according to device data sheet |
| پاکێج | 8-pin SOIC |
| مەودای پلەی گەرمیی کارکردن | -40 C to +85 C |
| جۆری دامەزراندن | Surface mount |
| دۆخی RoHS | Compliant |
| Lead-Free Status | Lead-free |
| Reference Interface | External voltage reference |
| Device Class | Low-power ADC |
ڕێکخستنی پینی MCP3202-CI/SN
| پین 1 | CS — Chip-select input |
| پین 2 | DIN — Serial data input |
| پین 3 | DOUT — Serial data output |
| پین 4 | CLK — Serial clock input |
| پین 5 | VREF- — Negative reference input |
| پین 6 | VREF+ — Positive reference input |
| پین 7 | VDD — Positive supply voltage |
| پین 8 | AGND — Analog ground |
بەکارهێنانە باوەکان
MCP3202-CI/SN گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Environmental Sensor Node, Industrial Process Monitoring, Temperature Measurement Bridge, Lab Data Acquisition Front End, Embedded Control and Feedback System, Arduino and Raspberry Pi Sensor Interface.
Battery-Powered Environmental Sensor Node
The MCP3202-CI/SN is suitable for measuring two low-bandwidth sensor signals in a portable environmental monitor. Its 12-bit SAR conversion provides 4096 digital codes, while the 2.7 V to 5.5 V operating range supports both low-voltage sensor systems and common 5 V supply arrangements. The converter can sample a temperature or humidity transducer and a second analog sensor through its SPI-compatible interface. Low standby current of 500 nA helps conserve energy when the controller wakes the ADC periodically. Keep the reference and analog input paths short, place bypass capacitance near the supply pins, and wake the device only around conversion windows when battery life is the primary constraint.
پێشنیارکراو
Industrial Process Monitoring
Use the MCP3202-CI/SN for two-channel industrial monitoring when the design needs a compact SPI ADC rather than a parallel interface. It can digitize a conditioned pressure, temperature, or level signal and a second reference or status channel. The 12-bit resolution is appropriate for many slow process signals, while the 100 ksps capability at 5 V provides headroom for sampled monitoring loops. The serial interface reduces PCB routing and is convenient for a microcontroller-based control board. Use an external reference with suitable stability, keep the analog trace away from switching nodes, and follow the manufacturer’s grounding and decoupling recommendations for reliable readings.
پێشنیارکراو
Temperature Measurement Bridge
The MCP3202-CI/SN can digitize the output of a resistive bridge or a ratiometric temperature sensor in a compact measurement circuit. The external reference helps define the full-scale input range, and the two input channels can support a sensor measurement plus a complementary or differential reading. At 5 V, the ADC can complete conversions at up to 100 ksps, although thermal applications usually require a much slower sampling rate to reduce noise and power use. Place the sensor and reference components near the analog pins, use a quiet reference path, and calibrate offset and gain in firmware to compensate for sensor and resistor tolerances.
پێشنیارکراو
Lab Data Acquisition Front End
The MCP3202-CI/SN can serve as a small two-channel data-acquisition front end for educational, prototyping, and bench instrumentation. A host microcontroller or single-board computer can read the SPI-compatible output while the ADC handles analog-to-digital conversion at up to 100 ksps at 5 V. The 12-bit resolution is sufficient for many slow laboratory waveforms, voltage observations, and control experiments. For higher bandwidth or lower noise requirements, external filtering, shielding, and a stable reference become increasingly important. The SOIC package also allows several instruments to share a common analog and digital grounding strategy when each channel has adequate isolation.
پێشنیارکراو
Embedded Control and Feedback System
The MCP3202-CI/SN is appropriate for embedded control loops that need two measured analog inputs, such as a setpoint and a feedback signal. Its SPI-compatible interface can share bus resources with other serial peripherals, while the 12-bit SAR conversion is fast enough for many motor, actuator, and thermal-control loops. The 2.7 V minimum supply supports compact battery or portable systems, while operation at 5 V provides the maximum conversion rate. Validate control-loop latency in software, use a regulator with adequate transient performance, and separate analog return currents from switching-node currents to reduce measurement error.
پێشنیارکراو
Arduino and Raspberry Pi Sensor Interface
The MCP3202-CI/SN is well suited to educational and prototyping boards that need more analog input than many built-in controllers provide. It exposes CS, DIN, DOUT, and CLK signals through an SPI-compatible interface, allowing a Raspberry Pi or an Arduino-compatible board to read two analog channels using a suitable voltage level arrangement. The 12-bit resolution improves resolution compared with an 8-bit converter, and the 2.7 V to 5.5 V range supports common board rails. Confirm logic levels, use a common ground, and choose the reference voltage carefully because it determines the digital code range and the maximum allowable input signal.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP3202-CI/SN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP3202-CI/SNVAO | MCP3202T-CI/SNVAO | MCP3202T-BI/SN | MCP3202-CI/ST | MCP3201-BI/SN |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Input Channels | 2 | 2 | 2 | 2 | 2 | 1 |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Interface | SPI-compatible | SPI-compatible | SPI-compatible | SPI-compatible | SPI-compatible | SPI-compatible |
جیاکەرەوە سەرەکییەکان
- Two-channel 12-bit conversion in an 8-pin SOIC (بەراورد بەMCP3201-BI/SN)
- 100 ksps maximum conversion rate at 5 V (بەراورد بەMCP3202-CI/SNVAO)
- Low-power operation for embedded measurements (بەراورد بەMCP3202-CI/ST)
تێبینییەکانی دیزاین
Place the input bypass capacitor and reference components close to the MCP3202-CI/SN supply and reference pins. Route the analog input traces away from SPI clock, digital control, and switching-node paths. Keep the analog ground connection short and return the reference current through a controlled path so digital switching activity does not modulate the conversion result.
Use a supply within the 2.7 V to 5.5 V operating range and account for the conversion-rate relationship: 50 ksps at 2.7 V and 100 ksps at 5 V. The typical active current is 375 uA, while standby current is 500 nA. These values support low-power operation, but the external reference, host controller, and sensor currents must be included in a complete power budget.
Do not assume that any related MCP3202 suffix is automatically interchangeable. Confirm the package code, pinout, temperature range, qualification, reference configuration, and lifecycle requirements against the manufacturer data sheet. Also ensure the analog input remains within the selected reference range; otherwise the ADC code can saturate or lose measurement accuracy.
زانیاری پابەندبوون
The product listing identifies the device as RoHS compliant and lead-free. REACH, halogen-free, and conflict-minerals status are not stated in the product information.