MCP3551T-E/SN 22-Bit Sigma-Delta ADC | Microchip Technology
MPN: MCP3551T-E/SN ✓ چالاکMCP3551T-E/SN گشتی
A delta-sigma ADC is an analog-to-digital converter that uses continuous-time sampling, noise shaping, and digital filtering to provide high-resolution conversion from a limited-resolution internal converter. The MCP3551 family combines this technique with fully differential inputs, making it suitable for sensor interfaces, pressure measurement, bridge transducers, and other systems where rejecting common-mode noise is valuable. Its 22-bit nominal resolution supports high-precision measurement while maintaining a compact, low-pin-count footprint.
The MCP3551T-E/SN provides an output noise figure listed as 2.5 uVRMS and an effective resolution of 21.9 bits. The product information also identifies automatic internal offset and gain calibration, which helps simplify signal-chain implementation and improve measurement consistency. The serial interface is identified as SPI compatible, allowing connection to a microcontroller or other digital controller for configuration and data transfer.
Because the converter is intended for precision analog measurement, the analog input network, reference voltage, grounding, and digital layout deserve careful attention. Fully differential operation helps reject disturbances common to both inputs, while filtering and calibration influence the final noise performance. The compact 8-pin SOIC package also makes the device suitable for designs where board space is constrained but industrial temperature performance is required.
Typical uses include industrial process control, sensor measurement, data acquisition, and precision instrumentation. When selecting the MCP3551T-E/SN, verify the input range, reference requirements, sampling behavior, calibration sequence, and SPI timing against the complete manufacturer datasheet. This page combines the manufacturer product information with distributor references and practical guidance for evaluating the converter in a new measurement design.
جێگرەوەکانی جێگۆڕکێ بۆ MCP3551T-E/SN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP3551T-E/SN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature Range, Output Noise, Package, Resolution, Analog Input.
MCP3551-E/SN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP3551T-E/SN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Converter Type | 22-bit single-channel delta-sigma ADC |
| Analog Input | 1 fully differential input |
| وردی | 22 bit |
| Effective Resolution | 21.9 bit |
| دەنگی دەرچوون | 2.5 uVRMS |
| ڕێژەی نموونەگرتن | 13.75 samples per second |
| Digital Interface | SPI-compatible serial interface |
| مەودای پلەی گەرمیی کارکردن | -40C to +125C |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Packaging | Tape and reel |
| Input Architecture | Fully differential analog input |
| Calibration | Automatic internal offset and gain calibration |
| Application Category | Industrial and process-control measurement |
| دۆخی RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
ڕێنمایی ڕێکخستنی پینی MCP3551T-E/SN 8-pin soic
ڕێکخستنی پین بۆ MCP3551T-E/SN (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP3551T-E/SN.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP3551T-E/SN گونجاوە بۆ 6 بەکارھێنانs: Industrial process measurement, Pressure transducer acquisition, Bridge sensor measurement, Precision data acquisition, RTD temperature acquisition, Test and measurement instrumentation.
Industrial process measurement
The MCP3551T-E/SN fits low-level industrial measurement circuits that require one differential analog channel rather than a multiplexed converter. Its 22-bit nominal resolution, 21.9-bit effective resolution, and 2.5 uVRMS output noise provide substantial conversion headroom for pressure, level, and process-variable signals. The fully differential input helps reject common-mode noise found near motors, relays, and long cable runs. The -40C to +125C operating range supports industrial environments, while the 8-pin SOIC keeps the analog front end compact. In a practical implementation, pair the converter with an appropriate low-noise reference, input protection, filtering, and carefully separated analog and digital return paths.
پێشنیارکراو
Pressure transducer acquisition
The MCP3551T-E/SN is suitable for bridge-based pressure transducers whose output is small, differential, and susceptible to interference. A 22-bit conversion resolution preserves fine measurement detail, while the fully differential input supports balanced excitation and signal return. The listed 2.5 uVRMS output noise is helpful when the transducer output approaches the converter noise floor. Designers should still calculate the full signal-chain error budget, including transducer sensitivity, excitation noise, reference error, input bias current, and filter tolerances. Use short, shielded sensor wiring where possible and confirm the converter's differential input limits in the manufacturer datasheet before finalizing the bridge network.
پێشنیارکراو
Bridge sensor measurement
The MCP3551T-E/SN can acquire Wheatstone bridge outputs in precision weighing, force, and position systems. Its differential input architecture matches the bridge output topology and helps reduce susceptibility to common-mode voltage and noise coupling. The converter's 22-bit nominal resolution is useful when mechanical resolution is higher than the signal noise and reference-error budget. For a practical design, select a low-noise excitation source, account for bridge imbalance in the allowable input range, and evaluate warm-up and offset behavior during calibration. The SPI-compatible interface also permits digital configuration and result transfer from a compact embedded controller without requiring a parallel data bus.
پێشنیارکراو
Precision data acquisition
The MCP3551T-E/SN supports compact precision data-acquisition modules that need a higher-resolution measurement channel without a wide parallel interface. Its 13.75 samples-per-second conversion capability is appropriate for slowly changing process signals rather than high-bandwidth waveform capture. The 21.9-bit effective resolution and 2.5 uVRMS output-noise figure can improve the dynamic range available from a low-level analog front end. Use the SPI interface for periodic reads and confirm the required data-ready behavior in firmware. Input filtering, reference layout, calibration state, and digital isolation should be designed together because each can affect the final laboratory-grade measurement result.
پێشنیارکراو
RTD temperature acquisition
The MCP3551T-E/SN can be considered for RTD temperature systems where a fully differential input and high nominal resolution are important. The architecture can support a resistive sensor with external excitation and appropriate lead-resistance compensation, provided the input range, excitation scheme, and conversion rate satisfy the application. At 13.75 samples per second, the device favors thermal systems that do not require rapid transient measurement. Engineer the bridge or ratiometric reference carefully because sensor self-heating and reference drift can otherwise dominate the achieved accuracy. Compare this option with an RTD-specific ADC when integrated excitation, IDAC, or two-wire lead compensation would materially simplify the design.
پێشنیارکراو
Test and measurement instrumentation
The MCP3551T-E/SN is appropriate for laboratory and field instrumentation requiring a single high-resolution measurement channel. Its fully differential input is compatible with carefully balanced source circuits, while automatic internal offset and gain calibration supports repeatable setup. The 8-pin SOIC footprint simplifies compact analog boards, and the extended temperature range supports equipment intended for demanding ambient conditions. For instruments, the reference voltage normally deserves separate low-noise regulation and buffering, while analog traces should remain short and surrounded by a continuous ground reference. The SPI interface can share a bus with other peripherals when chip-select, clocking, and digital return paths are handled according to the datasheet timing requirements.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ MCP3551T-E/SN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP3551-E/SN |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology |
| Resolution | 22 bit | 22 bit |
| Converter Architecture | Delta-sigma | Delta-sigma |
| Number of Inputs | 1 | 1 |
| Digital Interface | SPI-compatible serial interface | SPI-compatible serial interface |
| Operating Temperature Range | -40C to +125C | -40C to +125C |
جیاکەرەوە سەرەکییەکان
- High nominal resolution with a compact footprint (بەراورد بەMCP3551-E/SN)
- Differential measurement architecture (بەراورد بەMCP3551-E/SN)
- Low output noise for precision conversion (بەراورد بەMCP3551-E/SN)
تێبینییەکانی دیزاین
Place the converter close to the analog input network and keep the input traces short, symmetric, and surrounded by a continuous ground reference. Connect the analog ground and digital return strategy according to the manufacturer recommended layout, because a split or poorly connected ground can introduce error into the differential measurement. Place input protection and filtering components away from noisy digital clock and SPI return paths.
Use a low-noise reference and adequately decoupled supply rails. The MCP3551T-E/SN is a precision converter, so reference variation, supply noise, and input bias current can reduce the usable resolution of the 22-bit conversion. Verify capacitor voltage ratings and stability requirements in the manufacturer datasheet, and route reference and supply connections away from the SPI clock net.
Do not assume that a 22-bit nominal resolution equals 22-bit usable accuracy. Sensor noise, excitation noise, reference error, calibration residue, input overrange, and PCB leakage all contribute to the total measurement error. Establish the complete error budget for the selected bridge or sensor, and use the manufacturer pin-description table to confirm analog, reference, ground, and SPI connections before fabrication.
The differential input should be driven with balanced impedances and matched routing where practical. Avoid long parallel input traces, excessive connector breaks, and asymmetric filtering that can convert common-mode noise into differential error. The SPI interface is not the primary precision concern, but its clock edge can disturb the analog node through supply or substrate coupling; keep the clock route away from the converter and reference network.
زانیاری پابەندبوون
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is included in the referenced product information. The temperature range indicates industrial capability, but it does not by itself establish AEC-Q100 qualification.