MCP602-I/P - 2.8 MHz Dual CMOS Op Amp | Microchip
MPN: MCP602-I/P ✓ چالاکMCP602-I/P گشتی
An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines the gain of a closed-loop circuit. The MCP602 belongs to the hierarchy CMOS operational amplifier, analog amplifier, signal-conditioning IC, and broader power-management and semiconductor categories. Its two independent amplifier channels allow one package to implement functions such as voltage followers, transimpedance amplifiers, active filters, comparators, and level-shifting stages when supply and input ranges are appropriate.
The MCP602-I/P combines several useful low-power characteristics. Its 2.8 MHz gain-bandwidth product provides more bandwidth than typical micropower amplifiers, while the 230 uA typical operating current supports portable and battery-powered designs. Input bias current of 1 pA typical is particularly useful with high-impedance sensors. A unity-gain-stable architecture allows direct voltage-follower use, and the input common-mode range extending to ground simplifies single-supply signal conditioning. The rail-to-rail output improves usable output swing in low-voltage systems.
Microchip advanced CMOS technology provides low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. The device contains two independent amplifiers rather than one channel, making the 8-lead PDIP suitable for dual-stage analog signal paths. Its minimum operating supply of 2.7 V permits use from regulated 3.3 V systems, while the 6.0 V maximum supports conventional 5 V analog rails within the stated operating range.
Typical applications include low-power sensor interfaces, portable measurement systems, industrial process-control circuits, data-acquisition boards, test equipment, and low-end audio amplification or conditioning. In a transimpedance stage, the 1 pA typical input bias current helps limit photocurrent-generated error. In a voltage follower, unity-gain stability and the input range including ground simplify buffering of signals produced by sensors operating near 0 V.
Designers should verify signal amplitude, output swing, input common-mode range, noise, and stability under the intended loading before assigning the amplifier to a circuit. The PDIP package is convenient for prototyping, breadboards, and through-hole industrial assemblies, but its lead spacing differs from surface-mount packages. Decoupling and grounding remain important even though the MCP602-I/P is intended for low-power analog systems.
This product record combines manufacturer specifications, distributor availability, package information, engineering application guidance, and verified drop-in alternatives. It also distinguishes parameter differences among candidate devices so engineers can select a replacement without mistaking a same-family amplifier for a pin-compatible substitute.
جێگرەوەکانی جێگۆڕکێ بۆ MCP602-I/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP602-I/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Gain-Bandwidth Product.
MCP6002-I/P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP602-I/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifier Channels | 2 channels |
| Gain-Bandwidth Product | 2.8 MHz typical |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Operating Current | 230 uA typical per amplifier |
| ئێستای ئارام | Less than 325 uA per amplifier |
| Input Offset Voltage | Less than 2 mV |
| Input Bias Current | 1 pA typical |
| Common-Mode Rejection Ratio | 75 dB minimum |
| Gain Stability | Unity-gain stable |
| Output Swing | Rail-to-rail |
| Input Common-Mode Range | Includes ground |
| Supply Configuration | Single supply |
| Process Technology | Advanced CMOS |
| پاکێج | 8-lead PDIP |
| جۆری دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی MCP602-I/P 8-lead pdip
ڕێکخستنی پین بۆ MCP602-I/P (پاکێجی 8-lead pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP602-I/P.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP602-I/P گونجاوە بۆ 6 بەکارھێنانs: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instruments, Data Acquisition and Instrumentation, Industrial Process-Control Loops, Photodiode and High-Impedance Interfaces, Low-End Audio Conditioning.
Low-Power Sensor Signal Conditioning
The MCP602-I/P fits sensor front ends requiring low bias current and a moderate-bandwidth buffer. Its 1 pA typical input bias current limits the current drawn from high-impedance sources, while the 2.8 MHz typical gain-bandwidth product is substantially higher than that of many micropower amplifiers. The two independent channels can buffer a sensor output and provide a second gain or reference stage. Because the input common-mode range includes ground, the device is practical for sensors operating near 0 V, although source impedance, capacitance, noise, and settling accuracy must be evaluated before finalizing the gain.
Battery-Powered Portable Instruments
The MCP602-I/P is appropriate for battery-powered instruments where each additional microamp affects operating time. Typical operating current is 230 uA per amplifier, the supply can begin at 2.7 V, and the dual configuration can implement two signal-processing channels in one package. Rail-to-rail output operation helps preserve signal amplitude in low-voltage systems. The design should account for regulator efficiency, battery chemistry, output-load current, and leakage from the PCB. Unity-gain stability permits direct voltage-follower use, while the 2.8 MHz bandwidth supports higher-bandwidth acquisition than very-low-frequency micropower amplifiers.
Data Acquisition and Instrumentation
The MCP602-I/P can condition moderate-bandwidth sensor signals in data-acquisition and test-instrument front ends. Its 2.8 MHz typical gain-bandwidth product supports useful closed-loop bandwidth, and the dual amplifier can handle two related channels without requiring two packages. Rail-to-rail output and an input range including ground simplify single-supply instrumentation, while typical operating current of 230 uA per amplifier limits power demand. For accurate measurements, check input offset voltage against the required resolution, compare the 1 pA typical bias current with leakage in the complete analog front end, and verify settling behavior for the selected noise gain.
Industrial Process-Control Loops
The MCP602-I/P suits low-power process-control amplifier stages where sensor signals must be amplified before conversion or control. The device provides two channels, 2.8 MHz typical gain-bandwidth product, rail-to-rail output swing, and operation from a single 2.7 V-to-6.0 V supply. Its input common-mode range including ground supports circuits processing signals near the lower rail. In process applications, the exact ordering code must be checked for temperature range, qualification, and lifecycle requirements. Grounding, input filtering, output isolation, and stable feedback components remain critical because generic amplifier bandwidth alone does not establish control-loop accuracy.
Photodiode and High-Impedance Interfaces
The MCP602-I/P is well suited to high-impedance interfaces because its 1 pA typical input bias current limits amplifier-generated error at the sensing node. The dual package can implement a transimpedance stage and a subsequent voltage amplifier or active filter. Its 2.8 MHz typical gain-bandwidth product is more useful than a very-low-bandwidth micropower device, although it does not establish performance for every photodiode capacitance. The designer must calculate feedback resistance and capacitance based on the required transimpedance gain and settling behavior, and should include guarding and leakage control to prevent PCB contamination from dominating the very small bias-current specification.
Low-End Audio Conditioning
The MCP602-I/P can serve as a low-level audio buffer, gain stage, or active-filter element in entry-level audio equipment. Rail-to-rail output operation maximizes available signal swing in a single-supply design, and the 2.8 MHz typical gain-bandwidth product exceeds the bandwidth of many basic audio preamplifier stages. The dual amplifier allows two related functions to be packaged together. Audio performance nevertheless depends on output-load capability, distortion, noise, and supply decoupling, none of which are completely characterized in the supplied source snippets. The amplifier should therefore be verified against the required audio bandwidth and distortion target rather than treated as a full audio-power output device.
داتای سەرچاوەی ئەندازیاری بۆ MCP602-I/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP6002-I/P |
|---|---|---|
| Package | 8-lead PDIP | 8-lead PDIP |
| Brand | Microchip Technology | Microchip Technology |
| Number of Amplifier Channels | 2 channels | 2 channels |
| Gain-Bandwidth Product | 2.8 MHz typical | 1 MHz |
| Supply Voltage Range | 2.7 V to 6.0 V | 1.8 V to 6 V |
| Unity-Gain Stable | Yes | Yes |
جیاکەرەوە سەرەکییەکان
- Higher gain-bandwidth product (بەراورد بەMCP6002-I/P)
- Higher minimum operating supply (بەراورد بەMCP6002-I/P)
- Documented low-power operating characteristics (بەراورد بەMCP6002-I/P)
تێبینییەکانی دیزاین
Budget the MCP602-I/P supply current from the verified 230 uA typical operating current per amplifier, or less than 325 uA per amplifier as stated in the technical summary. Two active channels can therefore consume approximately 460 uA typical, before input bias current, load current, leakage, and board-level losses. Add regulator quiescent current when comparing complete battery-powered designs. Do not use the LCSC starting price as a power-budget figure; pricing and electrical consumption are independent constraints.
Do not substitute MCP6002-I/P solely because both are dual amplifiers in an 8-lead PDIP. The MCP602-I/P has a 2.8 MHz typical gain-bandwidth product, while the MCP6002 family is identified with 1 MHz bandwidth and a 1.8 V-to-6 V supply range. Before replacing the device, compare the complete manufacturer datasheets for offset voltage, bias current, common-mode range, output swing, noise, stability, and every numbered pin. The lower minimum supply of MCP6002-I/P may help a 1.8 V design, but it does not make all electrical specifications identical.
Route each amplifier's input, feedback components, and output to minimize parasitic capacitance and pickup, especially in the high-impedance applications supported by the 1 pA typical input bias current. Keep the power-supply bypass capacitor close to the device, provide an uninterrupted ground reference, and avoid placing high-current return paths beneath sensitive input traces. The verified source set does not provide the numbered PDIP pin assignments, so obtain the official package drawing before laying out a board or defining a replacement footprint.
زانیاری پابەندبوون
The supplied manufacturer and distributor snippets do not provide explicit compliance declarations for the MCP602-I/P ordering code. Arrow's category snippet contains an AEC-Q100 reference, but that is insufficient to classify this exact device as qualified. Compliance fields are therefore recorded as unknown.