Microchip Technology

MCP616-I/SN - 190 kHz Micropower Op Amp | Microchip

MPN: MCP616-I/SN ✓ چالاک
2.3 V to 5.5 V Vdss 19 µA Id 8-pin SOIC, 0.150 inch, MS-012 Package
MOQ: 1 |

MCP616-I/SN گشتی

The Microchip Technology MCP616-I/SN is a single, general-purpose operational amplifier with a 190 kHz gain-bandwidth product, typical operating current of 19 µA, typical input offset voltage below 150 µV, and an 8-pin SOIC package. It operates from a 2.3 V to 5.5 V single supply and provides a rail-to-rail output swing for low-voltage signal-conditioning systems.

An operational amplifier, commonly called an op amp, is a voltage-feedback amplifier used to amplify weak signals, buffer sensors, compare voltages, and drive analog inputs. The MCP616 belongs to the CMOS operational-amplifier hierarchy within the broader semiconductor and analog-IC categories. Its low operating current makes it especially useful in battery-powered and loop-powered equipment, where every microampere can affect the achievable service interval.

Key characteristics include low input bias current of 15 nA, low input offset voltage of up to ±150 µV, a typical slew rate of 0.08 V/µs, and a typical input noise specification of 2.2 µVP-P to 10 Hz. The rail-to-rail output allows useful signal swing near the supply rails, while the 190 kHz gain-bandwidth product supports low-frequency precision and general-purpose analog conditioning.

The MCP616 uses Microchip's advanced CMOS technology to combine low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. With a nominal operating current of 19 µA, it offers a practical balance between bandwidth, input accuracy, and power efficiency. The 2.3 V minimum supply voltage also makes the device compatible with modern low-energy 3 V and 5 V systems.

Typical applications include battery-operated instrumentation, industrial process-control inputs, portable measurement systems, test equipment, data-acquisition circuits, and low-end audio signal paths. The amplifier can also buffer sensors whose output impedance would otherwise prevent accurate downstream measurement. Selection should account for the 190 kHz bandwidth, output swing, input common-mode behavior, and the noise required by the target signal chain.

For a robust design, use a solid ground reference, decouple the supply close to the device, and confirm that source and load impedances do not degrade offset, bias-current, or noise performance. Because this is a single amplifier in an 8-pin SOIC, PCB layout and stability deserve attention before scaling the circuit into production.

This product page combines manufacturer specifications, application guidance, sourcing information, and a practical comparison of same-family alternatives. It is designed to help engineers confirm package compatibility, assess performance requirements, and select the appropriate amplifier without changing the target PCB footprint.

جێگرەوەکانی جێگۆڕکێ بۆ MCP616-I/SN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP616-I/SN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Supply Voltage Range, Input Common-Mode Range, Number of Channels.

Microchip Technology
Amplifier Type: Single operational amplifier
Package: 8-pin SOIC
Input Common-Mode Range: Rail-to-rail
Texas Instruments
Amplifier Type: Quad, general purpose, rail-to-rail input/output (RRIO)
Package: SOIC-14 (D), 0.154 in (3.90 mm) width
Supply Voltage Range: 2.7 V to 6 V (+/-1.35 V to +/-3 V)

MCP616T-I/SN

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Same 190 kHz gain-bandwidth product, 2.3 V to 5.5 V supply range, single-op-amp architecture, and 8-pin SOIC format; ordering suffix differs.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MCP618T-I/SN

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Same 190 kHz gain-bandwidth product, 2.3 V to 5.5 V supply range, and 8-pin SOIC format; device-specific offset and current limits require comparison.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MCP618T-I/SN

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin SOIC
Same 190 kHz gain-bandwidth product and 8-pin SOIC format as MCP616-I/SN; detailed bias-current and offset differences are not numerically documented here.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MCP616-I/SN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Circuits 1 circuit
Amplifier Type General Purpose
جۆری دەرچوون Rail-to-Rail
Supply Voltage Range 2.3 V to 5.5 V
Gain-Bandwidth Product 190 kHz
Typical Operating Current 19 µA
Typical Input Bias Current 15 nA
Maximum Input Offset Voltage ±150 µV
Typical Input Offset Current 0.3 nA
Slew Rate 0.08 V/µs
Input Noise 2.2 µVP-P typical to 10 Hz
Common-Mode Rejection Ratio 100 dB
مەودای پلەی گەرمیی کارکردن -40°C to +85°C
پاکێج 8-pin SOIC, 0.150 inch, MS-012
Packaging Tube
Technology Advanced CMOS
Lead-Free Status Lead-free
Product Status Active

ڕێنمایی ڕێکخستنی پینی MCP616-I/SN 8-pin soic, 0.150 inch, ms-012

ڕێکخستنی پین بۆ MCP616-I/SN (پاکێجی 8-pin soic, 0.150 inch, ms-012). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pin soic, 0.150 inch, ms-012 بۆ MCP616-I/SN

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP616-I/SN.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MCP616-I/SN گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Sensor Buffering, Industrial Process-Control Input, Portable Data Acquisition, Test and Measurement Equipment, Low-End Audio Signal Path, Loop-Powered Instrumentation.

📱

Battery-Powered Sensor Buffering

The MCP616-I/SN fits sensor-amplifier stages where a 19 µA typical operating current and 15 nA typical input bias current are important. Its 190 kHz gain-bandwidth product provides useful bandwidth for sensors whose output changes relatively slowly, while the maximum input offset voltage of ±150 µV supports accurate measurement of weak signals. Place the amplifier close to the sensor source, keep the input route short, and decouple the supply to reduce noise coupled into the high-impedance measurement path.

🏭

Industrial Process-Control Input

The MCP616-I/SN can condition low-level industrial sensor signals when the design operates from 2.3 V to 5.5 V and requires low amplifier current. Its 190 kHz gain-bandwidth product is suitable for process signals with modest bandwidth, and the ±150 µV maximum input offset specification supports precision-oriented gain stages. Confirm the input common-mode limits against the sensor output range and isolate sensitive inputs from switching equipment to prevent common-mode errors.

🧩

Portable Data Acquisition

The MCP616-I/SN is appropriate for portable data-acquisition front ends where a 19 µA typical operating current helps limit battery drain. Its 15 nA typical input bias current reduces loading on high-impedance transducers, while the 190 kHz bandwidth supports slow industrial, environmental, and physiological measurements. Use a low-leakage protection network, maintain a stable reference ground, and verify that the complete signal path—including ADC input leakage—meets the required error budget.

🔧

Test and Measurement Equipment

With a 190 kHz gain-bandwidth product and 0.08 V/µs slew rate, the MCP616-I/SN can perform low-frequency amplification and buffering in compact test instruments. Its general-purpose architecture suits source monitoring, threshold generation, and signal conditioning rather than demanding high-speed waveform work. For instrument-grade accuracy, check input offset over the full temperature range, account for resistor-network tolerance, and use a low-noise reference or supply arrangement to prevent the amplifier’s own characteristics from limiting measurement resolution.

🎧

Low-End Audio Signal Path

The MCP616-I/SN can support low-end audio buffering, gain control, and low-level mixing stages because it provides a rail-to-rail output and a 190 kHz gain-bandwidth product. Its low operating current is useful in portable audio equipment, while the 2.2 µVP-P typical noise to 10 Hz provides a useful starting point for low-frequency signal assessment. Keep the feedback network stable, avoid driving headphones directly, and confirm output-current requirements against the intended speaker or line-level load.

🏭

Loop-Powered Instrumentation

The MCP616-I/SN’s 2.3 V minimum supply voltage, 19 µA typical operating current, and low input bias current align well with loop-powered instrumentation powered from a restricted supply. The device can buffer the sensor signal before transmission or interface it to a low-power converter. Its 190 kHz bandwidth is sufficient for many slowly varying process variables, while the rail-to-rail output maximizes signal range at low supply voltages. Confirm the exact supply tolerance and transient conditions at the instrumentation node.

کورتەی بەرهەمە پێشنیارکراوەکان

MCP616T-I/SN Same-family low-power op-amp option بەکارهێنراوە لە: Battery-Powered Sensor Buffering, Industrial Process-Control Input, Portable Data Acquisition, Test and Measurement Equipment, Low-End Audio Signal Path, Loop-Powered Instrumentation MCP618T-I/SN Same-family 8-pin SOIC amplifier بەکارهێنراوە لە: Battery-Powered Sensor Buffering, Industrial Process-Control Input, Portable Data Acquisition, Test and Measurement Equipment, Low-End Audio Signal Path, Loop-Powered Instrumentation
What is the operating voltage range of MCP616-I/SN?
The MCP616-I/SN operates from a single supply of 2.3 V to 5.5 V. According to the Microchip Technology MCP616 product page, the device is designed for low-voltage battery, portable, and loop-powered systems. A 3 V or 5 V supply therefore falls within its specified operating range, although the output swing must remain compatible with the selected supply and load.
What are the key specifications of MCP616-I/SN that engineers should know?
The MCP616-I/SN is a single general-purpose op amp with a 190 kHz gain-bandwidth product, typical operating current of 19 µA, input bias current of 15 nA, maximum input offset voltage of ±150 µV, and a 0.08 V/µs slew rate. Microchip also specifies rail-to-rail output operation, a 2.3 V to 5.5 V supply range, and an 8-pin SOIC package.
Is MCP616-I/SN suitable for battery-powered applications?
Yes, the MCP616-I/SN is suitable for battery-powered and loop-powered equipment. Its typical operating current is only 19 µA, while its 2.3 V minimum supply voltage supports low-energy systems. The rail-to-rail output can improve signal utilization near the supply limit, but total system current should also include sensor, ADC, resistor-network, and power-management loads.
Where can I download the MCP616-I/SN datasheet PDF?
The official MCP616-I/SN technical documents are linked from the Microchip Technology MCP616 product page. The device is covered by the manufacturer’s MCP616 datasheet for the 2.3 V to 5.5 V micropower Bi-CMOS operational-amplifier family. Use the product page to access the current PDF and confirm that its ordering information and package details cover the -I/SN configuration.
Where can I find the MCP616-I/SN pinout?
The MCP616-I/SN pin assignment and package drawing are shown in the pin-description section of the Microchip MCP616 datasheet. The device uses an 8-pin SOIC package. Before assigning PCB tracks, use the manufacturer’s pin-description table and dimensional drawing to identify each lead and verify the -I/SN ordering code.
What can replace MCP616-I/SN?
The MCP616T-I/SN is the closest same-family replacement listed for MCP616-I/SN because it retains the 190 kHz gain-bandwidth product, 2.3 V to 5.5 V supply range, 8-pin SOIC format, and single-amplifier configuration. The MCP618T-I/SN is another same-family 8-pin SOIC option with a 190 kHz gain-bandwidth product, but its detailed electrical limits should be checked against the original design before substitution.
Is MCP616-I/SN the same as MCP616T-I/SN?
The MCP616-I/SN and MCP616T-I/SN are closely related Microchip MCP616-series devices with the same single-amplifier architecture, 190 kHz gain-bandwidth product, 2.3 V to 5.5 V supply range, and 8-pin SOIC format. The T designation reflects a different ordering or shipping configuration, so confirm the exact suffix, temperature grade, packaging details, and lifecycle status on the manufacturer page before treating them as identical.
What is the best drop-in replacement for MCP616-I/SN?
MCP616T-I/SN is the most direct same-package candidate identified for MCP616-I/SN. It offers the same 190 kHz gain-bandwidth product, 2.3 V to 5.5 V operating range, general-purpose single-op-amp configuration, and 8-pin SOIC package. A drop-in decision should still verify input bias current, offset voltage, common-mode range, output swing, and electrical test limits against the original circuit requirements.
When should I choose MCP616-I/SN over MCP618T-I/SN?
Choose MCP616-I/SN when a low-power 190 kHz general-purpose amplifier is sufficient and you want the established MCP616 ordering configuration. MCP618T-I/SN also provides a single 8-pin SOIC amplifier with a 190 kHz gain-bandwidth product, so it is attractive when its device-specific electrical limits meet the application better. Compare offset, bias current, noise, common-mode range, and supply behavior before finalizing the selection.
MCP616-I/SN vs MCP618T-I/SN - which is better for low-power sensors?
MCP616-I/SN is a strong choice for a low-power sensor buffer when its 19 µA typical operating current and 15 nA typical input bias current meet the sensor impedance and accuracy requirements. MCP618T-I/SN offers the same 190 kHz bandwidth and 8-pin SOIC package, but it should be selected when its specific offset, noise, and input-current characteristics provide a clearer advantage for the sensor interface.
Where to buy MCP616-I/SN online?
Use the Request a Quote form on this page to request MCP616-I/SN pricing, current inventory, and order handling. The form is the direct route for a quote and confirmed availability. Before ordering, specify the -I/SN suffix, quantity, tube quantity requirements, and destination country so the supplier can confirm the exact configuration and current lead time.
What is the price of MCP616-I/SN?
Current MCP616-I/SN pricing is obtained through the Request a Quote form on this page. The structured quote process reflects current inventory, quantity, and purchasing conditions without presenting a stale list figure. Include your required quantity and whether you need multiple tubes so the returned quotation corresponds to the intended production buy.
What is the lead time for MCP616-I/SN?
Submit MCP616-I/SN requirements through the Request a Quote form on this page to obtain the current lead time and stock position. Lead time can vary with quantity, tube quantity, and supply conditions, so the manufacturer and authorized distribution channels should confirm the production schedule. Requesting a dated commitment is recommended before committing the part to a production schedule.
Is MCP616-I/SN in stock?
The current stock status for MCP616-I/SN should be confirmed through the Request a Quote form on this page. The form supports a direct inquiry for the exact -I/SN ordering code and required quantity. Because inventory levels change, request both quantity and packaging details, and avoid treating a general-family listing as confirmation that the exact 8-pin SOIC configuration is available.
Is MCP616-I/SN compliant with RoHS and REACH?
The MCP616-I/SN is described as a lead-free plastic SOIC device, but its RoHS and REACH declarations should be confirmed for the exact ordering code. Use the Microchip product page and the manufacturer’s current compliance documentation for the authoritative declarations. For regulated production, record the applicable statement and document revision rather than relying only on a distributor classification.

داتای سەرچاوەی ئەندازیاری بۆ MCP616-I/SN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MCP616-I/SN when a low-power, single general-purpose op amp with a 190 kHz gain-bandwidth product, 19 µA typical operating current, and 8-pin SOIC package meets the design requirements. MCP616T-I/SN is the closest same-family alternative because it retains the same stated bandwidth, supply range, amplifier count, and package. Select it when its ordering configuration better matches the planned supply chain. MCP618T-I/SN also uses an 8-pin SOIC package and has a 190 kHz gain-bandwidth product, but its device-specific offset, noise, and bias-current limits should be checked before reuse. None of these choices automatically guarantees equivalence for every design: compare input common-mode range, output swing under load, output current, noise, stability, temperature limits, and production qualification. For a high-impedance sensor, the MCP616-I/SN’s 15 nA typical input bias current is particularly relevant. For battery operation, its 19 µA typical operating current provides a clear efficiency baseline.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MCP616T-I/SN MCP618T-I/SN
Package 8-pin SOIC, 0.150 inch, MS-012 8-pin SOIC 8-pin SOIC
Brand Microchip Technology Microchip Technology Microchip Technology
Number of Circuits 1 circuit 1 circuit 1 circuit
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
Gain-Bandwidth Product 190 kHz 190 kHz 190 kHz
Output Type Rail-to-Rail Rail-to-Rail Rail-to-Rail
Slew Rate 0.08 V/µs 0.08 V/µs 0.08 V/µs
Operating Temperature Range -40°C to +85°C -40°C to +85°C -40°C to +85°C

جیاکەرەوە سەرەکییەکان

  • Direct same-family package match (بەراورد بەMCP616T-I/SN)
  • Low operating current supports portable designs (بەراورد بەMCP618T-I/SN)
  • Low input offset supports precision conditioning (بەراورد بەMCP618T-I/SN)

تێبینییەکانی دیزاین

Route the inverting-input feedback connection directly to the amplifier and keep the non-inverting input trace short, especially when the source impedance is high. Place input protection components close to the connector rather than near the source device. This reduces parasitic pickup and prevents leakage from board contamination from creating errors comparable to the specified ±150 µV maximum input offset voltage.

Decouple the supply at the MCP616-I/SN with a local high-frequency capacitor and place it between the power and ground pins rather than at a distant power-entry point. Keep the ground return short and use a continuous ground plane. The device draws only 19 µA typically, but supply and layout noise can still dominate a high-impedance sensor signal and obscure the amplifier’s low-current capability.

Do not assume that rail-to-rail output means the input common-mode range covers both supply rails. Verify the MCP616-I/SN input common-mode limits against the sensor’s output range. Likewise, confirm output-current capability before driving a low-impedance load; rail-to-rail swing describes voltage range, not unlimited output current. These checks prevent clipping and unexpected common-mode error.

Use feedback resistors that produce the intended noise gain while maintaining stable operation with the chosen source capacitance. If the input source is capacitive, add a small series isolation resistor near the amplifier pin. The 190 kHz gain-bandwidth product is sufficient for many slow sensors and audio paths, but excessive source capacitance or an unsuitable feedback network can still create ringing or oscillation.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The device is identified as a lead-free plastic SOIC. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification declarations are not stated in the source information and remain unconfirmed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-10 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

mcp616 datasheet MCP616-I/SN datasheet MCP616-I/SN pinout MCP616-I/SN equivalent MCP616-I/SN replacement MCP616-I/SN drop-in replacement MCP616-I/SN application circuit MCP616-I/SN SOIC footprint MCP616-I/SN price MCP616-I/SN stock Microchip MCP616-I/SN MCP616-I/SN vs MCP618T-I/SN

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology MCP616-I/SN MCP616T-I/SN MCP618T-I/SN operational amplifier op amp general-purpose amplifier analog integrated circuit semiconductor CMOS advanced CMOS technology Bi-CMOS rail-to-rail output gain-bandwidth product input offset voltage input bias current CMRR slew rate quiescent current 8-pin SOIC MS-012 surface-mount package battery-powered equipment industrial process control data acquisition
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ