MCP633-E/SN - 24MHz RRIO Op Amp | Microchip Technology
MPN: MCP633-E/SN ✓ چالاکMCP633-E/SN گشتی
An operational amplifier is a high-gain analog building block that compares an input signal with a feedback-defined reference and amplifies the difference between them. Within the semiconductor hierarchy, the MCP633-E/SN belongs to the operational amplifier, analog amplifier, and integrated-circuit families. Its rail-to-rail behavior supports signal acquisition and output stages that operate close to the supply rails.
The MCP63x family provides high gain-bandwidth product and high output short-circuit current, while supported variants include a Chip Select control for low-power operation. For the MCP633-E/SN, key characteristics include 24 MHz typical gain-bandwidth, 10 V/µs typical slew rate, 78 dB CMRR, and a typical 70 mA output short-circuit current. These ratings support faster closed-loop response than general-purpose low-speed amplifiers.
Its operating range of 2.5 V to 5.5 V accommodates 3.3 V and 5 V systems. A typical 10 nV/√Hz voltage-noise density at 1 kHz is useful for sensors and instrumentation, while the 70 mA typical short-circuit current provides drive margin for moderate capacitive and resistive loads. The 8-pin SOIC package also supports conventional surface-mount assembly.
Typical uses include low-voltage sensor conditioning, active filtering, analog buffers, instrumentation, portable measurement systems, and mixed-signal signal processing. The MCP633-E/SN is particularly appropriate where a compact single amplifier, broad bandwidth, and rail-to-rail operation are required without the component count of a dual or quad amplifier.
Design the feedback network for stability, keep sensitive input nodes physically short, and use decoupling capacitors close to the supply pins. Confirm the actual output-current and capacitive-load limits for the operating condition because short-circuit current is not the maximum continuous load-current rating.
This page combines the manufacturer device description with practical package, application, and substitution guidance. It highlights where the MCP633-E/SN fits, which same-package alternatives require further qualification, and which layout and signal-integrity checks should be completed before production release.
جێگرەوەکانی جێگۆڕکێ بۆ MCP633-E/SN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP633-E/SN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Number of Circuits, Slew Rate, Automotive Qualification, Input Bias Current.
MCP631-E/SN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP633T-E/SN
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MCP663T-E/SN
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MCP633-E/SN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Gain-Bandwidth Product | 24 MHz typical |
| Slew Rate | 10 V/µs typical |
| Common-Mode Rejection Ratio | 78 dB |
| Voltage Noise Density | 10 nV/√Hz typical at 1 MHz |
| Output Short-Circuit Current | 70 mA typical |
| Input Bias Current | 0.0050 µA |
| Input Offset Voltage | 150 µV |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Chip Select | Supported by MCP633-E/SN |
| دۆخی RoHS | Compliant |
| Lead-Free Status | Lead-free |
ڕێنمایی ڕێکخستنی پینی MCP633-E/SN 8-pin soic
ڕێکخستنی پین بۆ MCP633-E/SN (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP633-E/SN.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP633-E/SN گونجاوە بۆ 6 بەکارھێنانs: Low-Voltage Sensor Signal Conditioning, Active Analog Filtering, Portable Measurement Front Ends, Analog Buffering and Level Translation, Industrial Instrumentation, Mixed-Signal Interface Circuits.
Low-Voltage Sensor Signal Conditioning
The MCP633-E/SN fits sensor front ends that operate from 2.5 V to 5.5 V and need usable signal range near the supply rails. Its rail-to-rail input and output characteristics provide additional headroom when conditioning signals from resistive dividers, potentiometers, and low-voltage sensors. The 24 MHz typical gain-bandwidth product and 10 V/µs typical slew rate allow reasonably fast closed-loop operation, while the 78 dB CMRR helps reject common-mode noise on the sensor lines. Confirm the sensor's output range and the amplifier's stability with the selected feedback network.
پێشنیارکراو
Active Analog Filtering
The MCP633-E/SN can implement active filters where a 24 MHz typical gain-bandwidth product provides useful bandwidth margin. Its 10 V/µs typical slew rate reduces distortion risk when a filter must preserve a moderately fast transient or waveform. The single-amplifier configuration is especially useful for second-order sections that would otherwise require additional buffers. Select resistor and capacitor values to set the intended pole and zero frequencies, then verify phase margin, output swing, and stability against the application bandwidth.
پێشنیارکراو
Portable Measurement Front Ends
The MCP633-E/SN is appropriate for compact, low-power measurement modules that need more bandwidth than a slow precision amplifier. A 2.5 V to 5.5 V supply range supports low-voltage portable equipment, while rail-to-rail operation improves utilization of the available signal range. The 70 mA typical short-circuit-current specification provides useful drive capability, but it must not be interpreted as a continuous-load rating. Battery-powered designs should also verify shutdown behavior, supply current, leakage, and whether the Chip Select function suits the product's power architecture.
پێشنیارکراو
Analog Buffering and Level Translation
The MCP633-E/SN can buffer a high-impedance source into a moderate resistive or capacitive load when unity-gain stability and output-swing requirements are met. Rail-to-rail output operation is valuable when the source approaches either supply rail, and the 10 V/µs typical slew rate supports higher-frequency signals than conventional low-speed buffers. Keep the feedback connection short and assess capacitive loading because the datasheet's typical short-circuit current does not define unlimited continuous drive capability. Include output-swing and distortion checks in the circuit simulation.
پێشنیارکراو
Industrial Instrumentation
The MCP633-E/SN is suitable for instrumentation modules that must process low-level analog signals from sensors while maintaining a compact surface-mount footprint. Its specified -40 °C to +125 °C operating range covers industrial temperature environments, and the 78 dB CMRR helps maintain signal integrity when the input is exposed to common-mode interference. The 8-pin SOIC package simplifies assembly, but industrial qualification, isolation, surge protection, and functional-safety requirements must be assessed separately for the finished equipment.
پێشنیارکراو
Mixed-Signal Interface Circuits
The MCP633-E/SN is useful between low-voltage sensors or analog sources and higher-impedance mixed-signal stages. Rail-to-rail inputs permit operation near the supply limits, and the 24 MHz typical gain-bandwidth product can accommodate signal paths faster than general-purpose amplifiers. The Chip Select feature can support controlled operating states in multi-amplifier systems, subject to its detailed logic and timing requirements. Validate settling behavior, noise contribution, and interaction with the downstream converter or microcontroller input before releasing the design.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP633-E/SN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP631-E/SN | MCP633T-E/SN | MCP663T-E/SN |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
جیاکەرەوە سەرەکییەکان
- High-speed response within a single-amplifier SOIC (بەراورد بەMCP631-E/SN)
- Closest same-family ordering candidate (بەراورد بەMCP663T-E/SN)
- Rail-to-rail operation in an 8-pin SOIC (بەراورد بەMCP631-E/SN)
تێبینییەکانی دیزاین
Place the input, output, supply, and bypass connections directly on the 8-pin SOIC footprint. Keep the feedback loop short and connect the output-side capacitor to the device ground reference rather than a distant ground plane segment. Because the device supports rail-to-rail operation and uses Chip Select, route the control signal away from sensitive input nodes to reduce coupling during mode changes.
Evaluate gain-bandwidth and slew-rate requirements together rather than using 24 MHz as a standalone signal-frequency limit. The feedback network determines actual bandwidth, phase margin, and output settling. Simulate the intended gain, source impedance, load capacitance, and tolerance of external resistors and capacitors; the 10 V/µs typical slew rate helps reduce large-signal distortion but does not guarantee stability with every load.
Do not use the 70 mA typical short-circuit-current value as a continuous output-load rating. Check output-current limits, output swing, and thermal behavior for the selected load. Also confirm the meaning and polarity of Chip Select in the Microchip MCP633 datasheet before using it for shutdown or power sequencing, because incorrect control logic can interrupt signal operation.
زانیاری پابەندبوون
RoHS-compliant and lead-free status is identified for MCP633-E/SN. Confirm additional environmental declarations for the exact ordering code before regulatory submission.