MK2049-36SILF - 77.76MHz 3.3V PLL Clock | Renesas
MPN: MK2049-36SILF ✓ چالاکMK2049-36SILF گشتی
A PLL clock synthesizer is a clock-and-timing integrated circuit that compares a reference signal with an internal feedback signal and generates a higher-frequency output with controlled phase relationships. In the broader semiconductor hierarchy, it belongs to clock generation, timing control, and frequency synthesis. Its output can provide a convenient clock source for transceivers, controllers, converters, and other digital systems that cannot directly operate from the crystal reference frequency.
The MK2049-36SILF operates from 3.3 V and produces a 77.76 MHz clock. Its 20-SOIC package supports conventional surface-mount PCB assembly. The manufacturer documentation recommends 0.01 µF decoupling capacitors between VDD and GND near the device, especially near pins 4 and 7, and 15 and 17. It also recommends 33 Ω series termination resistors on clock outputs when PCB traces exceed approximately 1 inch.
The PLL architecture allows the device to derive a higher-frequency communications clock while maintaining controlled frequency relationships. This is useful where a single reference oscillator must serve multiple timing requirements. Because clock edge quality affects downstream data integrity, the output nets should be routed away from high-current switching paths and terminated according to the actual trace geometry and receiver loading.
Typical uses include communications modules, clock-distribution networks, interface controllers, frequency-conversion stages, and digital subsystems requiring a 77.76 MHz reference. The part can also serve as a reference for designs using the Site MPN family of audio converters and interface ICs when their clock architecture requires a compatible source.
Layout is the primary design consideration. Place the 0.01 µF bypass capacitors directly beside their associated supply and ground pins, minimize the distance from the decoupling network to the package, and preserve a continuous ground reference beneath the device. Use short clock traces and add the recommended 33 Ω source termination when a trace approaches or exceeds 1 inch.
This product page combines the device specifications, package details, application guidance, replacement considerations, and practical PCB recommendations into a focused engineering reference. It also distinguishes documented functions from characteristics that still require confirmation in the manufacturer datasheet before production release.
جێگرەوەکانی جێگۆڕکێ بۆ MK2049-36SILF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MK2049-36SILF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
MK2049-34SILF
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2049-37SILF
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2049-38SILF
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2049-36SILF تایبەتمەندییەکان
| Device Type | PLL Clock Synthesizer / VCXO PLL Clock Synthesizer |
| Output Frequency | 77.76 MHz |
| ڤۆڵتیەی دابینکردن | 3.3 V |
| Output Count | 1 |
| پاکێج | 20-SOIC |
| Package Body Width | 7.50 mm |
| Package Width | 0.295 inch |
| جۆری دامەزراندن | Surface Mount |
| Decoupling Capacitor | 0.01 µF |
| Decoupling Placement | Close to pins 4, 7, 15, and 17 |
| Clock Output Series Termination | 33 Ω for traces longer than 1 inch |
ڕێنمایی ڕێکخستنی پینی MK2049-36SILF 0.295 inch
ڕێکخستنی پین بۆ MK2049-36SILF (پاکێجی 0.295 inch). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MK2049-36SILF.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MK2049-36SILF گونجاوە بۆ 6 بەکارھێنانs: Communications Module Clocking, Clock Distribution Network, Frequency Conversion Front End, Interface Controller Timing, Digital Audio Interface Timing, Industrial Control Timing.
Communications Module Clocking
The MK2049-36SILF fits communications modules that require a 77.76 MHz clock generated from a compatible reference through a 3.3 V PLL. The single 77.76 MHz output supports timing architectures where a fixed communications rate is needed downstream. Place 0.01 µF bypass capacitors beside the supply pins and use 33 Ω source termination when a clock trace exceeds approximately 1 inch, helping preserve a clean edge at the receiver.
پێشنیارکراو
Clock Distribution Network
The MK2049-36SILF can serve as the source in a clock-distribution network centered on a 77.76 MHz communications clock. Its 3.3 V operation and single PLL output suit compact interface boards that need a controlled reference rather than an uncontrolled oscillator. Route the source as a short, continuous clock path, add the recommended 33 Ω resistor for traces longer than approximately 1 inch, and keep the network isolated from high-current switching nodes.
پێشنیارکراو
Frequency Conversion Front End
The MK2049-36SILF is applicable where a communications subsystem needs a PLL-derived 77.76 MHz clock ahead of conversion or modulation circuitry. A stable clock simplifies rate coordination between the oscillator reference and downstream digital blocks. Its 20-SOIC package permits conventional surface-mount assembly, while the manufacturer-recommended 0.01 µF local decoupling helps prevent supply transients from disturbing the PLL and its clock output.
پێشنیارکراو
Interface Controller Timing
The MK2049-36SILF can provide the fixed 77.76 MHz timing reference for an interface controller whose internal logic requires a stable communications-rate clock. Operating from 3.3 V, the part avoids introducing a separate higher-voltage clock supply into a compact interface design. Correct decoupling and controlled source impedance are essential: place each 0.01 µF capacitor close to its power pin and terminate long clock traces with 33 Ω to limit ringing.
پێشنیارکراو
Digital Audio Interface Timing
The MK2049-36SILF can supply a stable communications clock to digital audio interfaces that synchronize converters and serial links. A fixed 77.76 MHz output is useful when the audio subsystem expects that specific rate, although the receiving device must support the same clock. Keep the 20-SOIC device close to the local supply bypass network and route the clock away from audio output switching stages to minimize coupled noise.
پێشنیارکراو
Industrial Control Timing
The MK2049-36SILF is suitable for industrial control electronics that need a deterministic 77.76 MHz communication clock from a 3.3 V supply. The surface-mount SOIC package supports compact controller and interface boards, while local bypass capacitors help isolate the PLL from digital switching noise. Confirm the reference-input requirements, output waveform, and temperature limits in the manufacturer datasheet before using the device in a safety-critical or extended-temperature installation.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MK2049-36SILF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MK2049-34SILF | MK2049-37SILF | MK2049-38SILF |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 20-SOIC | 20-SOIC | 20-SOIC | 20-SOIC |
| Product Type | PLL Clock Synthesizer | PLL Clock Synthesizer | PLL Clock Synthesizer | PLL Clock Synthesizer |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
جیاکەرەوە سەرەکییەکان
- Exact 77.76 MHz communications-clock option (بەراورد بەMK2049-34SILF)
- Single 3.3 V clock output (بەراورد بەMK2049-37SILF)
- Defined PCB implementation guidance (بەراورد بەMK2049-38SILF)
تێبینییەکانی دیزاین
Place 0.01 µF decoupling capacitors directly between the associated VDD and GND pins and the chip. The manufacturer specifically identifies pins 4 and 7, and pins 15 and 17, as areas requiring close capacitor placement. Minimize both capacitor-to-pin and capacitor-to-ground-loop length so switching current does not propagate through the same traces that supply the PLL. A solid, continuous ground plane beneath the device will reduce clock-supply coupling.
Use 33 Ω series termination at the clock output when the PCB trace is longer than approximately 1 inch under the manufacturer's 50 Ω trace assumption. Place the resistor close to the driver to isolate the source from the transmission line and reduce edge reflections. Re-evaluate termination if the receiver has a different input impedance or if the trace crosses a split or the board edge; excessive series resistance can degrade rise and fall times.
Route the 77.76 MHz clock as a short, continuous path away from power-conversion switches, clock-buffer outputs, and other high-current edges. Avoid stubs and unnecessary test pads because they create discontinuities that can produce ringing. Maintain a nearby ground reference beneath the clock trace, match the output impedance to the PCB construction, and keep the PLL reference and supply pins away from the clock output and termination resistor.
Do not select a replacement solely because it uses a 20-SOIC package or belongs to the MK2049 family. Confirm the complete pinout, 3.3 V supply compatibility, reference-input frequency, PLL configuration, output frequency, and output logic level before substitution. A package-compatible device can still fail if its reference architecture or frequency ratio differs. Validate the candidate with the manufacturer's timing specifications and perform eye, jitter, and startup measurements on the assembled board.
زانیاری پابەندبوون
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for this exact MPN. Confirm current declarations with Renesas before procurement.