MK2059-01SILF 25.92MHz Clock Translator | Renesas
MPN: MK2059-01SILF ✓ چالاکMK2059-01SILF گشتی
A VCXO-based clock frequency translator belongs to the clock and timing IC hierarchy, where it sits between a low-frequency synchronization reference and the higher-frequency clocks used by communications equipment. Unlike a simple frequency divider, this architecture uses a voltage-controlled crystal oscillator to generate the output clock and phase-lock it to the incoming 8 kHz frame signal. This makes the device relevant where equipment must derive a common reference frequency from an existing frame network.
The MK2059-01SILF is identified as a clock synthesizer and jitter-cleaning device with a 25.92 MHz output. Its 20-pin SOIC package provides a surface-mount implementation for telecommunications and other synchronous electronic systems. The 25.92 MHz result supports clocking roles requiring a substantially higher frequency than the 8 kHz synchronization reference, while the phase-locked architecture provides a defined relationship to the original frame timing.
Technically, the key operating concept is the interaction between the VCXO and the phase-locking loop. The frame reference establishes the target phase relationship, and the controlled oscillator produces the corresponding high-frequency output. Compared with distributing a free-running oscillator alone, this arrangement is intended for equipment that must remain aligned with a wider network timing reference. Detailed loop bandwidth, jitter, supply-voltage limits, and current limits must be confirmed in the manufacturer datasheet before release to production.
Typical applications include telecommunications line-card clocking, frame synchronization, network-interface timing, and embedded communications equipment. It can also be considered wherever an 8 kHz frame reference must be converted into a 25.92 MHz clock without redesigning the surrounding timing architecture. Designers should validate the reference frequency, output frequency, load requirements, and loop behavior against the complete system timing budget.
The primary design consideration is to treat the reference and output clocks as a controlled phase-locked system. Use the manufacturer pin-description table when assigning PCB tracks, and preserve the recommended grounding and decoupling arrangement around the clock and power pins. Because clock translators can amplify supply noise or layout disturbance into timing errors, short return paths and controlled impedance are especially important.
This page organizes the device function, package information, sourcing questions, drop-in comparison limits, and design cautions into a compact engineering reference. It also separates confirmed product facts from parameters that still require verification against the Renesas datasheet, helping designers avoid treating an incomplete clock specification as a production-ready guarantee.
جێگرەوەکانی جێگۆڕکێ بۆ MK2059-01SILF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MK2059-01SILF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Lead-Free Status, RoHS Status, Package.
MK2059-01SI
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MK2059-01SITR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MK2059-01SILFTR
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2059-01SILF تایبەتمەندییەکان
| Device Type | VCXO-based frame-clock frequency translator |
| Output Frequency | 25.92 MHz |
| Reference Input Frequency | 8 kHz |
| ژمارەی دەرچووەکان | 1 |
| Clock Architecture | VCXO-based |
| Phase-Locking Reference | 8 kHz frame-rate input reference clock |
| Device Classification | Clock synthesizer / jitter cleaner |
| پاکێج | 20-SOIC |
| Package Width | 0.295 inch (7.50 mm) |
| جۆری دامەزراندن | Surface mount |
| ژمارەی پینەکان | 20 pins |
| دۆخی RoHS | Compliant |
| Lead-Free Status | Lead-free |
ڕێنمایی ڕێکخستنی پینی MK2059-01SILF 0.295 inch (7.50 mm)
ڕێکخستنی پین بۆ MK2059-01SILF (پاکێجی 0.295 inch (7.50 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MK2059-01SILF.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MK2059-01SILF گونجاوە بۆ 6 بەکارھێنانs: Telecommunications Frame Synchronization, Network Interface Timing, Line-Card Clock Generation, Communications Equipment Reference Clock, Synchronous Test and Measurement Equipment, Industrial Synchronous Control.
Telecommunications Frame Synchronization
The MK2059-01SILF fits telecommunications equipment that must derive a 25.92 MHz operating clock from an 8 kHz frame-rate synchronization reference. Its VCXO-based architecture produces an output clock phase-locked to the frame input, allowing downstream circuits to operate at a higher frequency while maintaining a defined relationship with the network timing source. This is useful in line cards and transport systems where every timing domain must remain coordinated. Before implementation, confirm the reference waveform, allowable jitter, required pull range, loop acquisition behavior, and output load against the manufacturer datasheet. PCB routing should keep the reference path short, provide a stable return plane, and isolate the clock output from noisy switching nodes.
Network Interface Timing
The MK2059-01SILF can provide the 25.92 MHz timing reference for network-interface or communications modules that receive an 8 kHz frame signal from a broader system. Because the generated output is phase-locked to that reference, the design can coordinate a higher-frequency processing domain with the lower-rate network timing hierarchy. The device is particularly relevant where a free-running local oscillator would not preserve the required synchronization relationship. Confirm the required output phase, tolerance, jitter contribution, and load configuration before committing the device to a board. Controlled-impedance routing and a continuous ground reference are important because clock-edge distortion can consume timing margin even when the nominal frequency is correct.
Line-Card Clock Generation
In a telecommunications line card, the MK2059-01SILF converts an 8 kHz frame-rate reference into a 25.92 MHz clock for synchronous processing sections. The phase-locked VCXO architecture gives the board a common timing source without requiring every circuit block to run directly from the low-frequency frame signal. System planners should account for the device's reference sensitivity and loop performance when placing it relative to noisy power-conversion stages. Use solid ground-plane continuity and follow the manufacturer's recommended decoupling layout. The final frequency plan should verify that 25.92 MHz meets the processor, serializer, or memory timing requirements and that startup acquisition is acceptable after the reference becomes stable.
Communications Equipment Reference Clock
The MK2059-01SILF is applicable when communications equipment requires a stable 25.92 MHz reference derived from a shared 8 kHz timing signal. This arrangement supports equipment that must exchange information according to a system-wide frame cadence rather than relying on an unrelated local timebase. The single-output arrangement makes the device particularly relevant to compact designs with one principal logic-clock domain. Review output drive, jitter, startup time, and power-supply requirements in the Renesas document before simulation and release. Keep the crystal and timing loop layout unobstructed, avoid long stubs, and verify the 8 kHz reference amplitude and edge quality at the actual device pin.
Synchronous Test and Measurement Equipment
The MK2059-01SILF can support synchronized test and measurement equipment that distributes a 25.92 MHz clock generated from an 8 kHz frame reference. The resulting phase-locked clock can organize acquisition, modulation, or signal-processing sections around a common timing origin. Such use requires confirming that the device's jitter and frequency tolerance satisfy the measurement floor, which cannot be established from the family description alone. A controlled clock plane, short output path, and careful separation from high-current switching stages can reduce edge degradation. Validate acquisition after power-up and reference restart, and include the clock's phase and timing behavior in the instrument's uncertainty budget.
Industrial Synchronous Control
The MK2059-01SILF can generate a 25.92 MHz processing clock from an 8 kHz frame-rate reference in industrial control equipment where distributed subsystems must maintain a common timing relationship. The phase-locked output may suit motion, communications, or monitoring subsystems that already receive frame timing from a central controller. Engineers should confirm that the clock translator's electrical and environmental limits match the industrial enclosure temperature range and power architecture. Use the manufacturer application information to implement filtering, decoupling, and grounding, and avoid placing the reference input beside high-dv/dt motor-switching traces. Verify startup, loss-of-reference behavior, and phase alignment during fault recovery before using the clock for safety-relevant coordination.
داتای سەرچاوەی ئەندازیاری بۆ MK2059-01SILF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MK2059-01SI | MK2059-01SITR | MK2059-01SILFTR |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 20-SOIC | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Product Family | MK2059-01 | MK2059-01 | MK2059-01 | MK2059-01 |
| Pin Count | 20 pins | 20 pins | 20 pins | 20 pins |
جیاکەرەوە سەرەکییەکان
- Exact 25.92 MHz output from an 8 kHz frame reference (بەراورد بەMK2059-01SILFTR)
- Lead-free procurement configuration (بەراورد بەMK2059-01SI)
- Compliant standard order code for regulated production (بەراورد بەMK2059-01SITR)
تێبینییەکانی دیزاین
Route the 8 kHz reference and 25.92 MHz output as short, controlled-impedance clock traces with continuous ground-plane references. Keep the reference path away from switching-node traces, high-current inductors, and digital bus edges. Use the manufacturer's package and application diagrams for component placement, and avoid adding test-point stubs that can degrade edge quality. If the output must reach a distant circuit, evaluate buffer placement and trace length against the clock's rise and fall requirements.
Follow the Renesas datasheet's power-pin connection and decoupling recommendations exactly. Place the required input and output bypass capacitors at their specified pins with short ground connections, and avoid sharing narrow ground paths between the clock translator and switching regulators. Because clock jitter can rise when supply disturbance reaches the loop, evaluate the power rail under maximum output loading and during adjacent circuit switching rather than checking only quiescent operation.
Do not treat a matching 20-pin SOIC outline as sufficient proof of drop-in equivalence. Verify the complete order code, electrical grade, temperature range, reference configuration, output frequency, and shipment format in the Renesas ordering information. MK2059-01SI and MK2059-01SITR are documented as non-compliant and lead-containing, while MK2059-01SILFTR must be checked for the required commercial and reel configuration before substitution.
Validate the 8 kHz reference amplitude, edge rate, duty cycle, and phase noise at the device pin because phase-locking performance depends on the signal delivered at the actual input. Measure the 25.92 MHz output rise time, overshoot, undershoot, and jitter at the end of the routed path. Compare those measurements with the timing requirements of the receiving logic rather than relying only on the nominal frequency.
زانیاری پابەندبوون
The exact MK2059-01SILF order code is listed as RoHS compliant and lead-free. REACH, halogen-free, and conflict-minerals declarations are not established by the available product records.