NE5532ANG - Dual Low-Noise 8-PDIP Op Amp | onsemi
MPN: NE5532ANG ✓ چالاکNE5532ANG گشتی
An operational amplifier is a voltage-feedback amplifier that uses external feedback to control gain and signal behavior. A dual operational amplifier combines two amplifier channels in one package, reducing board area compared with separate single-channel devices. In the broader semiconductor hierarchy, the NE5532ANG belongs to the operational-amplifier family, which sits within amplifier ICs and analog signal-conditioning semiconductors. Its internal compensation simplifies implementation by allowing the manufacturer to establish stable operation without requiring a large external compensation network.
The primary engineering benefits are low input noise, dual-channel integration, and an 8-pin PDIP package suitable for conventional through-hole PCB assembly. Two amplifier circuits can implement functions such as preamplification, filtering, buffering, active crossover stages, or audio channel processing in a single package. The onsemi listing identifies the NE5532ANG as a standard general-purpose amplifier, while the manufacturer datasheet describes it as an internally compensated dual low-noise operational amplifier.
The NE5532 family is recognized for audio-focused signal-chain use, but its applications extend beyond simple volume control. Low-noise operation is valuable when the amplifier must preserve small signals without adding excessive broadband noise. Internal compensation supports practical feedback-based amplifier configurations, and the dual format allows a designer to use both amplifier sections for related analog functions rather than placing two separate packages on the board.
Typical uses include stereo audio preamplification, headphone-driver signal stages, active equalizer and crossover circuits, low-level sensor amplification, and general instrumentation buffers. The same package can also support two independent channels in test equipment or measurement interfaces. Selection should be based on the required supply voltage, signal amplitude, output loading, noise target, stability in the selected feedback network, and the surrounding circuit impedance.
For PCB implementation, follow the pin-description table in the manufacturer datasheet when assigning input, output, and supply traces. Place the manufacturer-recommended bypass capacitors close to the supply pins, keep input routing short and away from high-current switching nodes, and provide adequate output-current and thermal margin. Because the NE5532ANG is a through-hole PDIP device, verify the PCB drill pattern and pin-1 orientation rather than assuming a surface-mount footprint.
This page combines the exact manufacturer and distributor identity of NE5532ANG with package-specific pin guidance, application-oriented circuit considerations, drop-in replacement analysis, and an explicit separation of confirmed characteristics from parameters that still require engineering verification.
جێگرەوەکانی جێگۆڕکێ بۆ NE5532ANG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ NE5532ANG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Mounting Type, Slew Rate, Number of Circuits.
NE5532N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5532P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5532P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →OPA2604
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD823ARZ
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5532ANG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Dual internally compensated operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| ڤۆڵتاژی دابینکردنی کارکردن | 3 V to 20 V |
| پاکێج | 8-pin PDIP |
| Total Pin Count | 8 pins |
| جۆری دامەزراندن | Through-hole |
| Noise Classification | Low-noise operational amplifier |
| Compensation | Internal |
| Primary Application Category | Audio and instrumentation amplification |
ڕێکخستنی پینی NE5532ANG
| پین 1 | OUT A — Output of amplifier A |
| پین 2 | IN A- — Inverting input of amplifier A |
| پین 3 | IN A+ — Non-inverting input of amplifier A |
| پین 4 | V- — Negative power supply |
| پین 5 | IN B+ — Non-inverting input of amplifier B |
| پین 6 | IN B- — Inverting input of amplifier B |
| پین 7 | OUT B — Output of amplifier B |
| پین 8 | V+ — Positive power supply |
بەکارهێنانە باوەکان
NE5532ANG گونجاوە بۆ 6 بەکارھێنانs: Stereo Audio Preamplification, Active Crossover and Equalizer, Low-Level Sensor Instrumentation, Audio Test and Measurement Buffer, Headphone Output Driver, General-Purpose Analog Buffering.
Stereo Audio Preamplification
The NE5532ANG fits a stereo preamplifier because it combines two low-noise amplifier channels in one 8-pin PDIP package. According to the onsemi manufacturer datasheet, the device is an internally compensated dual operational amplifier specified from 3 V to 20 V, making it appropriate for conventional audio signal stages that require two channels and low added noise. Each section can amplify a left or right input through a feedback-defined gain network. Keep input traces short, avoid proximity to switching power nodes, and confirm output swing against the intended headphone or line-level load before layout release.
پێشنیارکراو
Active Crossover and Equalizer
The dual-channel structure of the NE5532ANG is useful in active crossover, equalizer, and tone-control boards where low-level audio signals must be shaped before a power amplifier. The onsemi manufacturer datasheet identifies the part as an internally compensated, low-noise dual operational amplifier, so both amplifier sections can be assigned to different filter or gain stages. Its 8-pin PDIP format simplifies through-hole construction and socket-based upgrades. Select resistor and capacitor values from the desired transfer function, then verify the gain, phase, output swing, and stability of each feedback network in simulation.
پێشنیارکراو
Low-Level Sensor Instrumentation
The NE5532ANG can serve as the front-end amplifier in instrumentation that handles low-level sensor signals. According to the onsemi manufacturer datasheet, it provides two internally compensated low-noise amplifier channels in an 8-pin PDIP, allowing a designer to combine signal conditioning and output buffering without two separate packages. The dual arrangement can support differential or single-ended amplifier configurations when the feedback network and source impedances are matched correctly. Check input bias current, common-mode range, offset, output swing, and noise requirements against the sensor before committing to the device.
پێشنیارکراو
Audio Test and Measurement Buffer
A dual NE5532ANG is practical in audio test equipment where two low-noise channels are needed for buffering, gain adjustment, or differential signal conditioning. The onsemi manufacturer datasheet describes an internally compensated dual low-noise operational amplifier with two independent amplifier sections in an 8-pin PDIP package. The dual organization allows a compact implementation while preserving conventional through-hole assembly. Maintain short signal paths, use low-leakage nodes around high-impedance inputs, and confirm output capability for the tester load. Decouple the supply rails according to the manufacturer application guidance.
پێشنیارکراو
Headphone Output Driver
The NE5532ANG can be used in line-level headphone-driver stages when the load and output-swing requirements remain within the device's operating limits. According to the onsemi manufacturer datasheet, the part combines low-noise performance with the output-drive characteristics associated with the NE5532 family and provides two amplifier sections in an 8-pin PDIP. Use one section for voltage gain and the other for buffering when appropriate, or distribute the channels across left and right outputs. Verify load impedance, headroom, distortion, and supply compatibility against the connected headphone before finalizing the circuit.
پێشنیارکراو
General-Purpose Analog Buffering
The NE5532ANG also supports general analog buffering where two low-noise amplifier sections can isolate a source from a following stage. According to the onsemi manufacturer datasheet, its internal compensation removes the need for a discrete compensation network, while the 8-pin PDIP package provides a straightforward through-hole implementation. The two channels may buffer separate signals or be combined into a differential stage when the feedback resistors are balanced. Choose the gain carefully, observe the input and output common-mode limits, and ensure the source impedance does not degrade offset or noise performance.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ NE5532ANG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | NE5532N | NE5532P | NE5532P | OPA2604 | AD823 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
جیاکەرەوە سەرەکییەکان
- Preserves the conventional 8-pin through-hole footprint (بەراورد بەAD823)
- Combines two amplifier channels in one package (بەراورد بەOPA2604)
- Specified for a 3 V to 20 V operating supply range (بەراورد بەTI NE5532P)
- Uses internal compensation for simplified feedback implementation (بەراورد بەNE5532N)
تێبینییەکانی دیزاین
Follow the onsemi datasheet pin-description table when assigning signals to the 8-pin PDIP footprint, and verify pin 1 against the PCB silkscreen or socket orientation before assembly. Keep each non-inverting input route short and away from output and supply traces. This is especially important in audio and instrumentation boards where a nearby high-current return can couple unwanted noise into a high-impedance amplifier input.
Use the supply-decoupling configuration and component recommendations shown in the onsemi datasheet, placing bypass capacitors close to the positive and negative supply pins. The stated operating range is 3 V to 20 V, but this range does not guarantee adequate output swing or common-mode headroom at every supply voltage. Check the selected feedback network and signal amplitude against the minimum and maximum operating conditions before committing the circuit.
Preserve a quiet analog signal path by separating low-level inputs from switching regulators, relay contacts, display drive circuitry, and high-current return paths. Use a compact ground strategy around the two amplifier sections and return output-current and load currents directly to the supply entry point. If a dual-supply circuit is used, provide a stable midpoint reference and account for the offset and noise introduced by that reference.
A matching 8-pin footprint does not by itself make every NE5532-family replacement electrically equivalent. Before substituting a part, compare minimum and maximum supply voltage, common-mode input range, output swing, input bias current, noise density, bandwidth, slew rate, output-current capability, and stability in the intended feedback network. Socketed audio boards are particularly prone to substitutions that change gain, bandwidth, or headroom.
زانیاری پابەندبوون
The product is an 8-pin PDIP general-purpose dual operational amplifier rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed against the current onsemi product documentation or declaration.